REVISIONS
LTR
A
B
C
D
E
DESCRIPTION
Add case outline 2. Editorial changes throughout.
Changes in accordance with NOR 5962-R027-95.
Update boilerplate to meet current requirements. -rrp
Update drawing as part of 5 year review. -rrp
Update drawing as part of 5 year review. - jt
DATE (YR-MO-DA)
90-06-20
94-11-04
00-11-02
05-12-20
10-11-17
APPROVED
Monica Poelking
Michael Frye
Raymond Monnin
Raymond Monnin
C. SAFFLE
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
REV
SHEET
PREPARED BY
JOSEPH A. KERBY
E
1
E
2
E
3
E
4
E
5
E
6
E
7
E
8
E
9
E
10
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
D. A. DiCENZO
APPROVED BY
MICHAEL A. FRYE
DRAWING APPROVAL DATE
87-12-08
REVISION LEVEL
E
SIZE
A
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
MICROCIRCUIT, LINEAR, PROGRAMMABLE GAIN
INSTRUMENTATION AMPLIFIER,
MONOLITHIC SILICON
CAGE CODE
AMSC N/A
67268
SHEET
1 OF 10
5962-87719
DSCC FORM 2233
APR 97
5962-E083-11
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-87719
01
E
A
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device type. The device type identify the circuit function as follows:
Device type
01
Generic number
AD625
Circuit function
Programmable gain instrumentation amplifier
1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
Package style
E
2
GDIP1-T16 or CDIP2-T16
CQCC1-N20
16
20
Dual-in-line
Square leadless chip carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
Supply voltage (V
S
) .....................................................................................
Internal power dissipation ...........................................................................
Input voltage ................................................................................................
Storage temperature range .........................................................................
Lead temperature (soldering, 10 seconds) ..................................................
Thermal resistance:
Junction-to-case (θ
JC
) ..............................................................................
Junction-to-ambient (θ
JA
) .........................................................................
±18
V dc
280 mW
±V
S
maximum
-55°C to +150°C
+300°C
See MIL-STD-1835
95°C/W
1.4 Recommended operating conditions.
Supply voltage range (V
S
) ...........................................................................
±6
V dc to
±18
V dc
Ambient operating temperature range (T
A
) ................................................. -55°C to +125°C
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-87719
SHEET
E
2
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 -
MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at
https://assist.daps.dla.mil/quicksearch/
or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Functional diagram. The functional diagram shall be as specified on figure 2.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD
PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
SIZE
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
A
REVISION LEVEL
5962-87719
SHEET
E
3
TABLE I. Electrical performance characteristics.
Conditions 1/
-55°C
≤
T
A
≤+125°C
unless otherwise specified
G=1
G = 10 2/ 3/
G = 100 2/ 3/
G = 1000 2/ 3/
G = 1 2/ 3/
G = 10 2/ 3/
G = 100 2/ 3/
G = 1000 2/ 3/
V
IN
= 0
V
IN
= 0
V
IN
= 0
V
IN
= 0
Test
Symbol
Group A
subgroups
1
1
1
1
1
1
1
1
1
2, 3
1
2, 3
Device
type
Min
01
01
01
01
01
01
01
01
01
01
01
01
Limits
Max
±0.05
±0.05
±0.05
±0.05
±5
±5
±5
±5
±200
±2
±5
±50
±50
±20
70
70
90
90
100
100
110
110
5
70
Unit
Gain error 1
Gain error 10
Gain error 100
Gain error 1000
Gain error drift 1
Gain error drift 10
Gain error drift 100
Gain error drift 1000
Input offset voltage
Input offset voltage drift
Output offset voltage
Output offset voltage
drift
Input bias current
Input offset current
Common mode rejection
Common mode rejection
Common mode rejection
Common mode rejection
Common mode rejection
Common mode rejection
Common mode rejection
Common mode rejection
Power supply current
Power supply rejection
GE1
GE10
GE100
GE1000
TCGE1
TCGE10
TCGE100
TCGE1000
V
OS
TCV
OS
V
OSO
TCV
OSO
%
%
%
%
ppm/°C
ppm/°C
ppm/°C
ppm/°C
µV
µV/°C
mV
µV/°C
I
B
I
OS
CMRR
-CMRR
CMRR
-CMRR
CMRR
-CMRR
CMRR
-CMRR
I
CC
PSRR
G=1
I
OS
= (I
B
+) – (I
B
-)
G=1
G=1
G = 10 2/
G = 10 2/
G = 100 2/
G = 100 2/
G = 1000
G = 1000
G=1
G=1
1
1
1
1
1
1
1
1
1
1
1
1
01
01
01
01
01
01
01
01
01
01
01
01
nA
nA
dB
dB
dB
dB
dB
dB
dB
dB
mA
dB
See footnotes at end of table.
SIZE
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
A
REVISION LEVEL
5962-87719
SHEET
E
4
TABLE I. Electrical performance characteristics – Continued.
Conditions 1/
-55°C
≤
T
A
≤+125°C
unless otherwise specified
G = 10 2/
G = 100 2/
G = 1000
Test
Symbol
Group A
subgroups
1
1
1
Device
type
01
01
01
Min
85
95
100
Limits
Max
Unit
Power supply rejection
Power supply rejection
Power supply rejection
PSRR
PSRR
PSRR
dB
dB
dB
1/
2/
3/
V
S
=
±15
V, R
L
= 2 kΩ, unless otherwise specified.
Guaranteed if not tested to the limits specified.
Gain error is a function of external resistors.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and
Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the
requirements of MIL-PRF-38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that
affects this drawing.
3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime’s agent, and the acquiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-87719
SHEET
E
5
stm32/stm8
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
