DATA SHEET
µ
PD120Nxx Series
THREE-TERMINAL LOW-DROPOUT POSITIVE-VOLTAGE REGULATOR
(OUTPUT CURRENT: 0.3 A)
MOS INTEGRATED CIRCUIT
DESCRIPTION
The
µ
PD120Nxx series provides low-voltage output regulators with the output current capacitance of 0.3 A. The
output voltage varies according to the product (1.5 V, 1.8 V, 2.5 V, or 3.3 V). The circuit current is low due to the
CMOS structure, so the power consumption in the ICs can be reduced. Moreover, since ICs are mounted in the small
package of the
µ
PD120Nxx series, this contributes to the miniaturization of the application set.
FEATURES
•
Output current: 0.3 A
•
On-chip overcurrent protection circuit
•
On-chip thermal protection circuit
•
Small circuit operation current: 60
µ
A TYP.
APPLICATIONS
Digital TV, Audio, HDD, DVD, etc.
PIN CONFIGURATION (Marking Side)
SC-74A
SC-62
N.C.
GND
GND
5
1
2
4
3
1
2
3
OUTPUT
GND
INPUT
OUTPUT
GND
INPUT
The information in this document is subject to change without notice. Before using this document, please
confirm that this is the latest version.
Not all products and/or types are available in every country. Please check with an NEC Electronics
sales representative for availability and additional information.
Document No. S17145EJ2V0DS00 (2nd edition)
Date Published February 2005 NS CP(K)
Printed in Japan
2005
µ
PD120Nxx Series
BLOCK DIAGRAM
INPUT
Overcurrent
Protection Circuit
Reference
Voltage
Circuit
+
Error
Amp.
−
OUTPUT
Thermal
Protection Circuit
GND
2
Data Sheet
S17145EJ2V0DS
µ
PD120Nxx Series
ORDERING INFORMATION
Part Number
Package
SC-74A
SC-62
SC-74A
SC-62
SC-74A
SC-62
SC-74A
SC-62
Output Voltage
1.5 V
1.5 V
1.8 V
1.8 V
2.5 V
2.5 V
.3.3 V
3.3 V
Marking
K71
7D
K72
7E
K73
7F
K74
7G
µ
PD120N15TA
µ
PD120N15T1B
µ
PD120N18TA
µ
PD120N18T1B
µ
PD120N25TA
µ
PD120N25T1B
µ
PD120N33TA
µ
PD120N33T1B
Remark
-E1 or -E2 is suffixed to the end of the part number of taping products, and -A or -AZ to that of Pb-free
products. See the table below for details.
Part Number
Note1
Package
SC-74A
SC-74A
SC-74A
•
Unit
•
Unit
Package Type
µ
PD120NxxTA
Note2
µ
PD120NxxTA-A
µ
PD120NxxTA-E1
•
8 mm wide embossed taping
•
Pin 1 on take-up side
•
3000 pcs/reel (MAX.)
µ
PD120NxxTA-E1-A
Note2
SC-74A
•
8 mm wide embossed taping
•
Pin 1 on take-up side
•
3000 pcs/reel (MAX.)
µ
PD120NxxTA-E2
SC-74A
•
8 mm wide embossed taping
•
Pin 1 on draw-out side
•
3000 pcs/reel (MAX.)
µ
PD120NxxTA-E2-A
Note2
SC-74A
•
8 mm wide embossed taping
•
Pin 1 on draw-out side
•
3000 pcs/reel (MAX.)
µ
PD120NxxT1B
Note3
µ
PD120NxxT1B-AZ
µ
PD120NxxT1B-E1
SC-62
SC-62
SC-62
•
Unit
•
Unit
•
12 mm wide embossed taping
•
Pin 1 on take-up side
•
1000 pcs/reel (MAX.)
µ
PD120NxxT1B-E1-AZ
Note3
SC-62
•
12 mm wide embossed taping
•
Pin 1 on take-up side
•
1000 pcs/reel (MAX.)
µ
PD120NxxT1B-E2
SC-62
•
12 mm wide embossed taping
•
Pin 1 on draw-out side
•
1000 pcs/reel (MAX.)
µ
PD120NxxT1B-E2-AZ
Note3
SC-62
•
12 mm wide embossed taping
•
Pin 1 on draw-out side
•
1000 pcs/reel (MAX.)
Notes 1.
xx stands for symbols that indicate the output voltage.
2.
Pb-free (This product does not contain Pb in external electrode and other parts.)
3.
Pb-free (This product does not contain Pb in external electrode.)
Data Sheet
S17145EJ2V0DS
3
µ
PD120Nxx Series
ABSOLUTE MAXIMUM RATINGS (T
A
= 25°C, unless otherwise specified.)
Parameter
Symbol
Rating
Unit
µ
PD120NxxTA
Input Voltage
Power Dissipation
Note1
µ
PD120NxxT1B
−0.3
to +6
V
400/2000
–40 to +85
–40 to +150
–55 to +150
Note3
V
IN
P
T
T
A
T
J
T
stg
R
th(J-A)
695/245
Note2
180/510
Note2
mW
°C
°C
°C
Operating Ambient Temperature
Operating Junction Temperature
Storage Temperature
Thermal Resistance (junction to ambient)
315/62.5
Note3
°C/W
Note 1.
Internally limited. When the operating junction temperature rises over 150°C, the internal circuit shuts down
the output voltage.
2
2.
Mounted on ceramic substrate of 75 mm x 0.7 mm
3.
Mounted on ceramic substrate of 16 cm
2
x 0.7 mm
Caution Product quality may suffer if the absolute maximum rating is exceeded even momentarily for any
parameter. That is, the absolute maximum ratings are rated values at which the product is on the
verge of suffering physical damage, and therefore the product must be used under conditions that
ensure that the absolute maximum ratings are not exceeded.
STANDARD CONNECTION
D
1
INPUT
C
IN
µ
PD120Nxx
C
OUT
D
2
OUTPUT
C
IN
: 0.1
µ
F or higher. Set this value according to the length of the line between the regulator and INPUT pin. Be sure
to connect C
IN
to prevent parasitic oscillation. If using a laminated ceramic capacitor, it is necessary to ensure
that C
IN
is 0.1
µ
F or higher for the voltage and temperature range to be used.
C
OUT
: 10
µ
F or higher. Be sure to connect C
OUT
to prevent oscillation and improve excessive load regulation. Place
C
IN
and C
OUT
as close as possible to the IC pins (within 2 cm). Be sure to use the capacitor of 10
µ
F or higher
of capacity values and 1 to 8
Ω
of equivalent series resistance under an operating condition.
D
1
: If the OUTPUT pin has a higher voltage than the INPUT pin, connect a diode.
D
2
: If the OUTPUT pin has a lower voltage than the GND pin, connect a schottky barrier diode.
Caution Make sure that no voltage is applied to the OUTPUT pin from external.
4
Data Sheet
S17145EJ2V0DS
µ
PD120Nxx Series
RECOMMENDED OPERATING CONDITIONS
Parameter
Input Voltage
Symbol
V
IN
Type Number
MIN.
3.0
3.2
4.5
4.5
0
−
40
−
40
TYP.
MAX.
5.5
5.5
5.5
5.5
0.3
+
85
+
125
Unit
V
V
V
V
A
°C
°C
µ
PD120N15
µ
PD120N18
µ
PD120N25
µ
PD120N33
Output Current
I
O
All
All
All
Operating Ambient Temperature T
A
Operating Junction Temperature T
J
Caution Use of conditions other than the above-listed recommended operating conditions is not a problem
as long as the absolute maximum ratings are not exceeded. However, since the use of such
conditions diminishes the margin of safety, careful evaluation is required before such conditions are
used. Moreover, using the MAX. value for all the recommended operating conditions is not
guaranteed to be safe.
ELECTRICAL CHARACTERISTICS
µ
PD120N15 (T
J
= 25°C, V
IN
= 5.0 V, I
O
= 0.15 A, C
IN
= 0.1
µ
F, C
OUT
= 10
µ
F, unless otherwise specified.)
Parameter
Output Voltage
Line Regulation
Load Regulation
Quiescent Current
Quiescent Current Change
Output Noise Voltage
Ripple Rejection
Dropout Voltage
Short Circuit Current
Peak Output Current
Temperature Coefficient of
Output Voltage
Symbol
V
O1
V
O2
REG
IN
REG
L
I
BIAS
3.0 V
≤
V
IN
≤
5.5 V, 0 A
≤
I
O
≤
0.3 A
3.0 V
≤
V
IN
≤
5.5 V
0 A
≤
I
O
≤
0.3 A
I
O
= 0 A
3.0 V
≤
V
IN
≤
5.5 V
10 kHz
≤
f
≤
100 kHz
f = 1 kHz, 3.0 V
≤
V
IN
≤
5.5 V
I
O
= 0.15 A
I
O
= 0.3 A
I
Oshort
I
Opeak
V
IN
= 5 V
V
IN
= 5 V
I
O
= 0 A, 0°C
≤
T
J
≤
125°C
Conditions
MIN.
1.47
1.455
−
−
−
−
−
−
−
−
−
0.3
−
TYP.
1.5
−
1
2
60
−
100
63
0.6
1.0
0.2
−
0.01
MAX.
1.53
1.545
30
30
120
25
−
−
0.9
−
−
−
−
Unit
V
V
mV
mV
µ
A
µ
A
µ
V
r.m.s.
dB
V
V
A
A
mV/°C
∆
I
BIAS
V
n
R•R
V
DIF
∆
V
O
/
∆
T
µ
PD120N18 (T
J
= 25°C, V
IN
= 5.0 V, I
O
= 0.15 A, C
IN
= 0.1
µ
F, C
OUT
= 10
µ
F, unless otherwise specified.)
Parameter
Output Voltage
Line Regulation
Load Regulation
Quiescent Current
Quiescent Current Change
Output Noise Voltage
Ripple Rejection
Dropout Voltage
Short Circuit Current
Peak Output Current
Temperature Coefficient of
Output Voltage
Symbol
V
O1
V
O2
REG
IN
REG
L
I
BIAS
3.2 V
≤
V
IN
≤
5.5 V, 0 A
≤
I
O
≤
0.3 A
3.2 V
≤
V
IN
≤
5.5 V
0 A
≤
I
O
≤
0.3 A
I
O
= 0 A
3.2 V
≤
V
IN
≤
5.5 V
10 kHz
≤
f
≤
100 kHz
f = 1 kHz, 3.2 V
≤
V
IN
≤
5.5 V
I
O
= 0.15 A
V
IN
= 5 V
V
IN
= 5 V
I
O
= 0 A, 0°C
≤
T
J
≤
125°C
Conditions
MIN.
1.764
1.746
−
−
−
−
−
−
−
−
0.3
−
TYP.
1.8
−
1
2
60
−
120
63
0.4
0.2
−
0.01
MAX.
1.836
1.854
30
30
120
25
−
−
0.65
−
−
−
Unit
V
V
mV
mV
µ
A
µ
A
µ
V
r.m.s.
dB
V
A
A
mV/°C
∆
I
BIAS
V
n
R•R
V
DIF
I
Oshort
I
Opeak
∆
V
O
/
∆
T
Data Sheet
S17145EJ2V0DS
5
电子竞赛
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
