DATA SHEET
MOS INTEGRATED CIRCUIT
µ
PD75P336
4-BIT SINGLE-CHIP MICROCOMPUTER
DESCRIPTION
The
µ
PD75P336 is a version of the
µ
PD75336 in which the on-chip mask ROM is replaced by one-time
PROM.
As the
µ
PD75P336 is user-programmable, it is suitable for preproduction in system development, and for
short-run and multiple device-production.
Detailed function description, etc. are described in the following User's manual. Be sure to read it when
designing.
µ
PD75336 User's Manual: IEU-725
FEATURES
•
µ
PD75336 compatible
•
Memory capacity:
• PROM : 16256
×
8 bits
• RAM : 768
×
4 bits
•
Operable over same supply voltage range as mask ROM
µ
PD75336
• V
DD
= 2.7 to 6.0 V
•
On-chip 8-bits resolution A/D converter (successive approximation type)
•
On-chip LCD controller/driver
ORDERING INFORMATION
Ordering Code
Package
80-pin plastic QFP (
14mm)
80-pin plastic TQFP (fine pitch)( 12mm)
Quality Grade
Standard
Standard
µ
PD75P336GC-3B9
µ
PD75P336GK-BE9
5
Note
Pull-up resistor cannot be incorporated by mask option.
Please refer to “Quality grade on NEC Semiconductor Devices” (Document number IEI-1209) published by
NEC Corporation to know the specification of quality grade on the devices and its recommended applications.
The information in this document is subject to change without notice.
Document No. IC-2980A
(O. D. No. IC-8371A)
Date Published October 1993P
Printed in Japan
The mark
5
shows major revised points.
© NEC Corporation 1993
2
PORT0
4
P00-P03
AN0-AN7*
8
AV
REF
AV
SS
A/D
CONVERT-
ER
BLOCK DIAGRAM
BASIC
INTERVAL
TIMER
PORT 1
4
P10-P13
SP(8)
CY
ALU
PORT 3
4
4
PORT 4
P30-P33
/MD0-MD3
P40-P43
4
PORT 2
4
P20-P23
PROGRAM
COUNTER
(15)
INTBT
TI0/P13
PTO0/P20
TIMER/EVENT
COUNTER
#0
INTT0
TI1/P80
PTO1/P21
PORT 5
TIMER/EVENT
COUNTER
#1
BANK
INTT1
GENERAL REG.
PROGRAM
MEMORY
(ROM)
16256
×
8 BITS
DECODE
AND
CONTROL
DATA
MEMORY
(RAM)
768
×
4 BITS
P50-P53
PORT 6
4
P60-P63
BUZ/P23
WATCH
TIMER
PORT 7
4
P70-P73
INTW
f
LCD
SI/SB1/P03
SO/SB0/P02
SCK/P01
CLOCKED
SERIAL
INTERFACE
PORT 8
4
P80-P83
12
8
4
CPU
CLOCK
f
LCD
PCL/P22
*
XT1 XT2 X1 X2
AN6/P82, AN7/P83
V
PP
V
DD
V
SS
RESET
3
S12-S23
S24/BP0
–S31/BP7
COM0–COM3
V
LC0
–V
LC2
INTCSI
INT0/P10
f
X
/ 2
N
INT1/P11
INT2/P12
INTER-
RUPT
CONTROL
LCD
CONTROL-
LER
/DRIVER
INT4/P00
KR0/P60
–KR3/P63
KR4/P70
–KR7/P73
8
SYSTEM CLOCK
CLOCK
CLOCK
GENERATOR STAND BY
OUTPUT
DIVIDER
SUB MAIN CONTROL
CONTROL
BIT SEQ.
BUFFER (16)
BIAS
LCDCL/P30
SYNC/P31
µ
PD75P336
µ
PD75P336
PIN CONFIGURATION (Top View)
q
80-pin plastic QFP (s 14mm)
s
q
80-pin plastic TQFP (fine pitch) (s 12mm)
s
P73/KR7
P72/KR6
P71/KR5
P70/KR4
P63/KR3
P62/KR2
P61/KR1
P60/KR0
RESET
X2
AV
REF
AV
SS
AN5
AN4
AN3
5
X1
V
PP
*
XT2
XT1
S31/BP7
S30/BP6
S29/BP5
S28/BP4
S27/BP3
S26/BP2
S25/BP1
S24/BP0
S23
S22
S21
S20
S19
S18
S17
S16
S15
S14
S13
S12
1
2
3
4
5
6
7
8
9
8079787776 757473 7271 70696867666564636261
V
DD
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
AN2
AN1
AN0
P83/AN7
P82/AN6
P81
P80/TI1
P33/MD3
P32/MD2
P31/SYNC/MD1
P30/LCDCL/MD0
P23/BUZ
P22/PCL
P21/PTO1
P20/PTO0
P13/TI0
P12/INT2
P11/INT1
P10/INT0
P03/SI/SB1
µ
PD75P336GC-3B9
µ
PD75P336GK-BE9
10
11
12
13
14
15
16
17
18
19
20
2122232425 262728 2930 31323334353637383940
P53
P00/INT4
*
In normal operation, V
PP
should be connected to V
DD
directly.
P01/SCK
P02/SO/SB0
COM0
COM1
COM2
COM3
BIAS
V
LC0
V
LC1
V
LC2
P41
P42
P43
V
SS
P40
P50
P51
P52
3
µ
PD75P336
PIN NAME
P00 to 03
P10 to 13
P20 to 23
P30 to 33
P40 to 43
P50 to 53
P60 to 63
P70 to 73
P80 to 83
BP0 to 7
KR0 to 7
AV
REF
AV
SS
AN0 to 7
SCK
SI
SO
MD0 to 3
V
PP
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Port 0
Port 1
Port 2
Port 3
Port 4
Port 5
Port 6
Port 7
Port 8
Bit Port
Key Return
Analog Reference
Analog Ground
Analog Input 0 to 7
Serial Clock
Serial Input
Serial Output
Mode Selection
Programming/Verifying
Power Supply
SB0, 1
RESET
S12 to 31
COM0 to 3
V
LC0 to 2
BIAS
LCDCL
SYNC
TI0, 1
PTO0, 1
BUZ
PCL
INT0, 1, 4
INT2
X1, 2
XT1, 2
V
DD
V
SS
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Serial Bus 0,1
Reset Input
Segment Output 12 to 31
Common Output 0 to 3
LCD Power Supply 0 to 2
LCD Power Supply Bias Control
LCD Clock
LCD Synchronization
Timer Input 0, 1
Programmable Timer Output 0, 1
Buzzer Clock
Programmable Clock
External Vectored Interrupt 0, 1, 4
External Test Interrupt 2
Main System Clock Oscillation 1, 2
Subsystem Clock Oscillation 1, 2
Positive Power Supply
Ground
4
µ
PD75P336
CONTENTS
1. PIN FUNCTIONS ......................................................................................................................................... 6
1.1
1.2
1.3
PORT PINS ............................................................................................................................................................. 6
OTHER PINS .......................................................................................................................................................... 8
PIN INPUT/OUTPUT CIRCUITS ...........................................................................................................................10
2. DIFFERENCES BETWEEN
µ
PD75P336 AND
µ
PD75336 ......................................................................... 13
2.1
2.2
PROGRAM MEMORY (PROM) 16256 WORDS
×
8 BITS .................................................................................. 14
DATA MEMORY (RAM) 768 WORDS
×
4 BITS .................................................................................................. 15
3. INSTRUCTION SET AND INSTRUCTION OPERATIONS ....................................................................... 16
4. ONE-TIME PROM (PROGRAM MEMORY) WRITE AND VERIFY OPERATIONS .................................. 25
4.1
4.2
4.3
PROGRAM MEMORY WRITE/VERIFY OPERATING MODES ........................................................................... 26
PROGRAM MEMORY WRITE PROCEDURE ....................................................................................................... 27
PROGRAM MEMORY READ PROCEDURE ......................................................................................................... 28
5. ELECTRICAL SPECIFICATIONS ................................................................................................................ 29
6. PACKAGE INFORMATION ........................................................................................................................ 48
7. RECOMMENDED SOLDERING CONDITIONS ......................................................................................... 50
APPENDIX A. LIST OF FUNCTIONS.............................................................................................................. 51
APPENDIX B. DEVELOPMENT TOOLS ......................................................................................................... 52
5
MicroPython开源版块
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
