Release
by
PARALIGHTDCC
PARA LIGHT ELECTRONICS CO., LTD.
4F, No.1, Lane 93, Chien Yi Road, Chung Ho City, Taipei, Taiwan,
Tel: 886-2-2225-3733
Fax: 886-2-2225-4800
http://www.para.com.tw
E-mail: para@para.com.tw
DATA SHEET
PART NO. : A431G-N G/W
REV :
A/3
CUSTOMER’S APPROVAL : _______________
DRAWING NO. : DS-11-03-0119
DCC : ____________
Page : 1
DATE : 2013-04-11
Release
by
PARALIGHTDCC
0.43
INCH SINGLE
DIGIT DISPLAY
REV:A / 3
A431G-N G/W
PACKAGE DIMENSIONS
NOTES : 1. All dimensions are in millimeters. (inches)
2. Tolerance is
6
0.25(0.010") unless otherwise specified.
3.Pls. contact with us when your production need to be
operated under the Pb free process.
DRAWING NO. : DS-11-03-0119
DATE : 2013-04-11
Page : 2
Release
by
PARALIGHTDCC
0.43
INCH SINGLE
DIGIT DISPLAY
REV:A / 3
A431G-N G/W
FEATURES
Û
Û
Û
Û
Û
Û
Û
10.92mm (0.43 inch ) DIGIT HEIGHT
COMMON ANODE
I.C. COMPATIBLE
LOW POWER CONSUMPTION
Pb FREE PRODUCTS
ROHS COMPLIANCE
GRAY FACE, WHITE SEGMENTS
Raw Material : GaAlInP/GaAs
ABSOLUTE MAXIMUM RATING : ( Ta = 25BC )
SYMBOL
PAD
VR
IAF
IPF
-
Topr
Tstg
PARAMETER
Power Dissipation Per Segment
Reverse Voltage Per Segment
Continuous Forward Current Per Segment
Peak Forward Current Per Segment (Duty-
0.1,1KHz)
Derating Linear From 25BC Per Segment
Operating Temperature Range
Storage Temperature Range
YELLOW GREEN
75
5
25
100
0.33
UNIT
mW
V
mA
mA
mA/BC
-35BC
to 85BC
-35BC
to 85BC
Solder Temperature 1/16 inch Below Seating Plane for 3 Seconds at 250BC
ELECTRO-OPTICAL CHARACTERISTICS : ( Ta = 25BC )
SYMBOL
VF
IR
lP
lD
Δl
IV
PARAMETER
Forward Voltage , Per Segment
Reverse Current , Per Segment
Peak Emission Wavelength
Dominant Wavelength
Spectral Line Half-Width
Luminous Intensity Per Segment
TEST
CONDITION
IF = 20mA
VR = 5V
IF = 20mA
IF = 20mA
IF = 20mA
IF = 10mA
568
570
30
2.0
MIN.
TYP.
2.1
MAX.
2.8
100
UNIT
V
mA
nm
nm
nm
mcd
DRAWING NO. : DS-11-03-0119
DATE : 2013-04-11
Page : 3
Release
by
PARALIGHTDCC
0.43
INCH SINGLE
DIGIT DISPLAY
REV:A / 3
A431G-N G/W
DRAWING NO. : DS-11-03-0119
DATE : 2013-04-11
Page : 4
Release
by
PARALIGHTDCC
0.43
—SOLDERING
METHOD
INCH SINGLE DIGIT DISPLAY
A431G-N G/W
REV:A / 0
SOLDERING CONDITIONS
REMARK
—
Solder no closer than 2mm from
DIP
SOLDERING
Bath temperature: 250 max
Immersion time: within 3 sec
the base of the package
—
Using soldering flux,” RESIN FLUX”
is recommended.
—
During soldering, take care not to
Soldering iron: 30W or smaller
press the tip of iron against the
SOLDERING
Temperature at tip of iron: 260
℃
or lower PIN.
IRON
Soldering time: within 5 sec.
(To prevent heat from being
transferred directly to the PIN.)
1) When soldering the PIN of Display in a jig that the package is fixed with a panel (See fIg.1), be
careful not to stress the PIN with iron tip. When soldering Display in a condition that the package
is fixed with a panel, be careful not to cling and stress the surface of Display on the panel to avoid
damaging the Display.
Fig.1
Regarding solution in the tinning oven for product-tinning, compound sub-solution made of tin &
copper and sliver is proposed with the temperature of Celsius 260. The proportion of the
alloyed solution is tin 95.5: copper 3.5: silver 0.5 by percentage. The time of tinning is constantly
3 seconds.
DRAWING NO. : DS-11-03-0119
DATE : 2013-04-11
Page : 5