REVISIONS
LTR
A
B
C
D
E
F
G
H
J
DESCRIPTION
Added case outline “F” and made editorial changes to reflect the inclusion. – lgt
Add CAGE 65342 for device type 02 with radiation hardened requirements.
Add case outline X. - ro
Make change to I
I
, t
PLZ
, t
PHZ
, t
PZH
, t
PZL
tests as specified in table - ro
Add device type 03. Editorial changes throughout. - lgt
Make changes to 1.5 and I
CC
and I
CCZ
in table I. - lgt
Add case outline Z. Changes to 1.2.4, 1.3, and figure 1. - lgt
Make changes to 1.5 and to footnote 2/ in table I for device type 01. - lgt
Add appendix A. Update drawing to reflect current requirements. - rrp
Make change to the
JA
limit for case outlines F and Z as specified
under 1.3. - ro
Make change to the input voltage limit under 1.3 for device type 01.
Add a footnote to 1.5 for device type 01. Add the words, “For device type 02
and 03” to Neutron irradiation footnote under 1.5. Make changes to 3.2.3 and
delete Table III entirely. Add paragraphs 2.2, 4.4.4.3, 6.7, and Table IB. - ro
DATE (YR-MO-DA)
97-11-21
00-05-25
01-01-08
01-06-13
01-10-04
02-04-21
02-09-05
04-04-19
06-02-15
APPROVED
R. MONNIN
R. MONNIN
R. MONNIN
R. MONNIN
R. MONNIN
R. MONNIN
R. MONNIN
R. MONNIN
R. MONNIN
K
10-10-05
C. SAFFLE
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
K
15
K
16
K
17
K
18
REV
SHEET
PREPARED BY
SANDRA ROONEY
K
19
K
20
K
1
K
2
K
3
K
4
K
5
K
6
K
7
K
8
K
9
K
10
K
11
K
12
K
13
K
14
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
SANDRA ROONEY
APPROVED BY
MICHAEL A. FRYE
DRAWING APPROVAL DATE
96-05-03
REVISION LEVEL
K
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
MICROCIRCUIT, LINEAR, LVDS QUAD CMOS
DIFFERENTIAL LINE RECEIVER, MONOLITHIC
SILICON
SIZE
A
CAGE CODE
AMSC N/A
67268
SHEET
1 OF 20
5962-95834
DSCC FORM 2233
APR 97
5962-E335-10
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and
M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part
or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN.
1.2 PIN. The PIN is as shown in the following example:
5962
-
95834
01
V
F
A
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
/
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
\/
Drawing number
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are
marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
02
03
Generic number
DS90C032
UT54LVDS032
UT54LVDSC032
Circuit function
Radiation hardened, LVDS quad CMOS
differential line receiver
Radiation hardened, LVDS quad CMOS
differential line receiver
Radiation hardened, LVDS quad CMOS
differential line receiver with cold spare
on LVDS bus
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as
follows:
Device class
M
Device requirements documentation
Vendor self-certification to the requirements for MIL-STD-883 compliant, non-
JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A
Certification and qualification to MIL-PRF-38535
Q or V
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
F
X
Z
2
Descriptive designator
GDFP2-F16 or CDFP3-F16
CDFP4-F16
GDFP1-G16
CQCC1-N20
Terminals
16
16
16
20
Package style
Flat pack
Flat pack
Flat pack with gull wing leads
Square leadless chip carrier
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-95834
SHEET
K
2
1.3 Absolute maximum ratings. 1/
Supply voltage ........................................................................................................... -0.3 V to +6.0 V
Input voltage :
Device type 01 ....................................................................................................... -0.3 V to 5.8 V
Device types 02 and 03 ......................................................................................... -0.3 V to (V
CC
+ 0.3 V)
Enable input voltage (ENABLE,
ENABLE
) ............................................................... -0.3 V to (V
CC
+ 0.3 V)
Output voltage (R
OUT
) ...............................................................................................
Storage temperature range .......................................................................................
Maximum power dissipation (P
D
):
Cases F and Z .......................................................................................................
Case X ...................................................................................................................
Case 2 ...................................................................................................................
Lead temperature (soldering, 10 seconds) ................................................................
Junction temperature (T
J
) ..........................................................................................
Thermal resistance, junction-to-case (
JC
):
Cases F and Z ........................................................................................................
Case X ...................................................................................................................
Case 2 ...................................................................................................................
Thermal resistance, junction-to-ambient (
JA
):
Cases F and Z .......................................................................................................
Case X ...................................................................................................................
Case 2 ...................................................................................................................
1.4 Recommended operating conditions.
Supply voltage ........................................................................................................... 4.5 V to 5.5 V
Receiver input voltage ............................................................................................... GND to 2.4 V
Ambient operating temperature range (T
A
) ............................................................... -55C to +125C
1.5 Radiation features.
Maximum total dose available (dose rate = 50 – 300 rads(Si)/s):
Device type 01 .......................................................................................................
Device type 02 .......................................................................................................
Device type 03 .......................................................................................................
Neutron irradiation :
Device types 02 and 03 .........................................................................................
Single event latch-up (SEL):
Device type 01 .......................................................................................................
-0.3 V to (V
CC
+ 0.3 V)
-65C to +150C
1400 mW 2/
1250 mW 2/
1830 mW 2/
+260C
+150C 3/
19C/W
10C/W
20C/W
145C/W
120C/W
82C/W
50 Krads (Si) 4/
1 Mrads (Si)
300 Krads (Si)
5/
120
MeV-cm /mg
2
2
Device type 02 and 03 ...........................................................................................
100
MeV-cm /mg
Single event functional interrupt (SEFI):
2
Device type 01 only ................................................................................................
100
MeV-cm /mg
______
1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
2/ At T
A
+25C, the derating factor for cases F and Z is 9.3 mW/C, 12.2 mW/C for case 2, and 0.4 mW/C for case X.
3/ For device types 02 and 03, the maximum junction temperature may be increased to +175C during burn-in and life test.
4/ Device type 01 is irradiated at dose rate = 50 - 300 rads(Si)/s in accordance with MIL-STD-883, method 1019, condition A,
and is guaranteed to a maximum total dose specified. The effective dose rate after extended room temperature
anneal = 0.19 rad(Si)/s per MIL-STD-883, method 1019, condition A, section 3.11.2. The total dose specification for this
device only applies to the specified effective dose rate, or lower, environment.
13
2
5/ For device types 02 and 03, neutron irradiation is not tested but guaranteed up to 1 x 10 neutron/cm .
Contact manufacturer for requirements beyond this level.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-95834
SHEET
K
3
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 -
MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at
https://assist.daps.dla.mil/quicksearch/
or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein.
Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.
AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)
ASTM F1192
-
Standard Guide for the Measurement of Single Event Phenomena (SEP) Induced by Heavy Ion
Irradiation of semiconductor Devices.
(Copies of these documents are available online at
http://www.astm.org
or from ASTM International, 100 Barr Harbor Drive,
P.O. Box C700, West Conshohocken, PA, 19428-2959).
2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.1.1 Microcircuit die. For the requirements of microcircuit die, see appendix A to this document.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Radiation exposure table. For device types 01, 02, and 03, the radiation exposure circuit shall be maintained by the
manufacturer under document revision level control and shall be made available to the preparing and acquiring activity upon
request.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-95834
SHEET
K
4
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table IA and shall apply over the
full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table IA.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be
in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of
supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of
MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of
product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing.
3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime 's agent,
and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore
documentation shall be made available onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in
microcircuit group number 77 (see MIL-PRF-38535, appendix A).
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-95834
SHEET
K
5
stm32/stm8
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
