MX21 INSTA-MOUNT™
|
SERIES
MODULAR INCREMENTAL ROTARY OPTICAL ENCODER
Introduction
By the time you have read this first sentence, you could have installed
the model MX21 INSTA-MOUNT™ modular optical encoder. In addition
to its quick and easy installation, the MX21 is designed to operate with
jitter-free output signals without tight controls on shaft endplay, runout,
or perpendicularity. The new INSTA-MOUNT™ encoder is capable of
operating within a temperature range of -10°to +70°C, requiring less
than 30 milliamps of L.E.D. current, without degradation of output
signals and is short circuit protected.
The MX21 is perfectly suited for motor manufacturers and other high
volume OEMs. The INSTA-MOUNT™ Series encoder offers 5V TTL
compatible quadrature outputs with index and complements as options.
Axial shaft movements during operation, of ±0.010”, will not adversely
affect the output signals. Shaft runouts of 0.005” TIR can also be
absorbed by this device without affecting output signal performance.
SPECIFICATIONS
Mechanical
Dimensions
Weight
Moment of Inertia
Bore Size
See Figure 1
2.1 oz. (Approx.)
2.6 x 10
-5
oz in sec
2
see “Ordering Options”
Motor Interface
Mount Holes
Mount Hardware
Perpendicularity Shaft to Mount
Shaft Runout
Shaft Endplay Dynamic or Static
Shaft Finish
Shaft Tolerance
Shaft Length
#4-40 or M3 x 0.5 @ 180° on 1.812” dia. B.C.
2 socket head cap screws
0.002” TIR
0.005” max (each 0.0001 degrades accuracy by 0.5 arc minutes)
±0.010”
16 micro inches or better. End must be chamfered or rounded
nominal -0.0002”/-0.0007”
0.56” minimum (remove cover button for motor through-shafts)
Page 1
Copyright © 2018 Sensata Technologies, Inc.
www.sensata.com
Electrical
Code
Pulses per revolutions (PPR)
Index Pulse Options
Supply Voltage
Output Format
Incremental
See Ordering Options
MX212: No Index
MX213, MX216: U = Ungated Index, G = Gated Index
5 volts ±5% @ 80mA max.
MX212: Dual channel in quadrature
MX213: Dual channel in quadrature with index
MX216: Dual channel in quadrature with index and complements
MX212 & 213 :
square wave TTL. 16mA sink 500ΩA source.
Short circuit protected
MX216:
TTL differential line driver (26LS31 or equiv.) should be
terminated into a line receiver (26LS32, or equivalent circuit)
Frequency (kHz) = (RPM X PPR)/60
1.0μ sec. max.
Output Type
Frequency Response
Rise Time
Enviromental
Temperature
Operating: -10°C to +70°C
Storage: -40°C to +125°C
Terminations
Ribbon
Round Cable
*NOTE: See pinout tables, under “Terminations” section.
28 AWG flat ribbon cable with 10 position connector Berg P/N 65863-165
or equiv. Mates with Berg P/N65863-165 or equiv) (mating connector not
provided)
28AWG 8 Conductor shielded cable
DIMENSIONS
All dimensions are in: inches .xx = ±0.02, .xxx = ±0.005
Fig.1
Page 2
Copyright © 2018 Sensata Technologies, Inc.
www.sensata.com
INSTALLATION INSTRUCTIONS
Preparation
1. Inspect motor interface per MX21 Data Sheet or specification drawing.
2. Motor shaft must be free of burrs & other surface defects.
Installation
1. Motor shaft should NOT be rotating during initial encoder installation.
2. Hold encoder perpendicular to motor shaft. Guide the encoder onto the motor shaft, pushing encoder STRAIGHT on until it is flush against
the mount surface. Do NOT rock side to side.
3. Install two #4-40 mount screws. Do not fully tighten at this point. (Note: A thread sealant should be applied to the screw threads)
4. Rotate the motor shaft (300 RPM, minimum). Press the air-gap button until it bottoms to the top of the encoder momentarily, then release.
CAUTION: DO NOT press air-gap button while motor shaft is stationary. Button should only be pressed for one or two seconds while shaft
is rotating.
5. Tighten mounting screws fully. (recommended torque is 30 to 40 ounce inches.)
6. This completes the mechanical installation. Proceed with electrical connections as indicated on product data sheet or specification
drawing.
Removal
1. Motor shaft may be stationary or rotating up to 1000 RPM during encoder removal.
2. Remove two mounting screws.
3. Grasp encoder firmly and pull STRAIGHT off of the motor shaft. Do NOT rock side to side.
Page 3
Copyright © 2018 Sensata Technologies, Inc.
www.sensata.com
OUTPUT WAVEFORM
TERMINATIONS
Pinout MX212/213
PIN #
1
2
3
4
5
Signal
Channel A
+5 volts
Ground
NC
NC
PIN #
6
7
8
9
10
Signal
NC
NC
Channel B
NC
Index (213)
PIN #
1
2
3
4
5
NC
Pinout MX216
Signal
+5 volts
Ground
NC
Channel A
PIN #
6
7
8
9
10
Signal
Channel A
Channel B
Channel B
Index
Index
Color Codes
Red
Black
White
Green
Orange
Blue
White/Black
Red/Black
+5 volts
Ground
A
B
Index
A
B
Index
Page 4
Copyright © 2018 Sensata Technologies, Inc.
www.sensata.com
ORDERING OPTIONS
MX21
X
Example : MX213-38-512-G-R18
Use this diagram, working from left to right to construct your model number
-
XX
-
XXXX
-
X
-
XXX
Output Format
2 =
Quadrature
3 =
Quadrature w / index
6 =
Quadrature w / index & complements
Bore Size
25 =
.25”
38 =
.375”
6M =
6mm
8M =
8mm
10M =
10mm
Pulses Per Revolution (PPR)
200, 400, 500, 512, 1000, 1024
Index Option
*For Output Formats 3 and 6 ONLY
G =
gated to data A & B
U =
ungated
Electrical Termination
Cxx =
Round Shielded Cable
Rxx =
Ribbon Cable with 10 Pin Socket Header
(xx = length of cable in inches; 18 inches standard)
Page 5
Sensata Technologies, Inc. (“Sensata”) data sheets are solely intended to assist designers (“Buyers”) who are developing systems that
incorporate Sensata products (also referred to herein as “components”). Buyer understands and agrees that Buyer remains responsible
for using its independent analysis, evaluation and judgment in designing Buyer’s systems and products. Sensata data sheets have
been created using standard laboratory conditions and engineering practices. Sensata has not conducted any testing other than that
specifically described in the published documentation for a particular data sheet. Sensata may make corrections, enhancements,
improvements and other changes to its data sheets or components without notice.
Buyers are authorized to use Sensata data sheets with the Sensata component(s) identified in each particular data sheet. HOWEVER, NO
OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER SENSATA INTELLECTUAL PROPERTY RIGHT, AND
NO LICENSE TO ANY THIRD PARTY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT, IS GRANTED HEREIN. SENSATA DATA SHEETS
ARE PROVIDED “AS IS”. SENSATA MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO THE DATA SHEETS OR USE
OF THE DATA SHEETS, EXPRESS, IMPLIED OR STATUTORY, INCLUDING ACCURACY OR COMPLETENESS. SENSATA DISCLAIMS
ANY WARRANTY OF TITLE AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, QUIET
ENJOYMENT, QUIET POSSESSION, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS WITH REGARD
TO SENSATA DATA SHEETS OR USE THEREOF.
All products are sold subject to Sensata’s terms and conditions of sale supplied at
www.sensata.com
SENSATA ASSUMES NO LIABILITY
FOR APPLICATIONS ASSISTANCE OR THE DESIGN OF BUYERS’ PRODUCTS. BUYER ACKNOWLEDGES AND AGREES THAT IT IS SOLELY
RESPONSIBLE FOR COMPLIANCE WITH ALL LEGAL, REGULATORY AND SAFETY-RELATED REQUIREMENTS CONCERNING ITS PRODUCTS,
AND ANY USE OF SENSATA COMPONENTS IN ITS APPLICATIONS, NOTWITHSTANDING ANY APPLICATIONS-RELATED INFORMATION
OR SUPPORT THAT MAY BE PROVIDED BY SENSATA.
Mailing Address: Sensata Technologies, Inc., 529 Pleasant Street, Attleboro, MA 02703, USA.
CONTACT US
Americas
+1 (800) 350 2727
sales.beisensors@sensata.com
Europe, Middle East & Africa
+33 (3) 88 20 8080
position-info.eu@sensata.com
Asia Pacific
sales.isasia@list.sensata.com
China
+86 (21) 2306 1500
Japan
+81 (45) 277 7117
Korea
+82 (31) 601 2004
India
+91 (80) 67920890
Rest of Asia
+886 (2) 27602006
ext 2808
Copyright © 2018 Sensata Technologies, Inc.
No. 02122-001 Rev: 05/09/2018
www.sensata.com
消费电子
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
