NATIONAL HYBRID INC.
RONKONKOMA, NY 11779
Miniature, Hermetically Sealed
Darlington Optocoupler
NHI 6033
NHI-6033
ANODE
1
CATHODE
2
4
COLLECTOR
3
EMITTER
Features;
·
·
·
·
·
·
-55°c to +125°c Operation
Output Voltage to 30V
Input Current from < 0.2mA
Low Output Saturation Typ < 1.0V
Withstanding Voltage > 1500Vdc
Functionally Compatible with 4N33
Terminal
Number
1
2
3
4
Terminal
Function
ANODE
CATHODE
EMITTER
COLLECTOR
Absolute Maximum Ratings;
Supply Voltage (Vcc) ………………………………….. -0.5 to 30Vdc
Continuous Input Current ……………………………… 60mA
Peak Input Current If (10uS,300Hz) …………….….... 3A
Reverse Input Voltage Vr ……………………………... 5 Vdc
Led Power Dissipation (At Tc=25°c)………………….. 100mW
Output Current ………………………………………….. 100mA
Output Voltage …………………………………………..-0.5 to 35Vdc
Output Power Dissipation ……………………………… 300mW
Storage Temperature ………………………………….. -65°C to 150°C
Lead Solder Temperature ……………………………... 260°C for 10 sec.
Recommended Operating Conditions;
Output Voltage Range .................................................... to 30Vdc
Input Current ................................................................... 0.5 mA to 15mA
Ambient Operating Temperature Range ........................ -55°C to 125°C
Page 1
NHI 6033
Electrical Performance Characteristics;
(At Ta = 25°c unless otherwise specified)
GROUP
A SUB-
GROUP
LIMITS
UNITS
MIN
500
1,2,3
100
200
30
5.0
1,2.3
1,2,3
1,2
1,2,3
5.0
60
7.5
1.0
100
1.7
30
Vdc
Vdc
Vdc
nAdc
Vdc
Vdc
%
TEST
SYM-
BOL
TEST CONDITIONS
Vce = 10V, If =1mA (at Ta = 25°C) _1
MAX
Current Transfer Ratio
Ctr
Vce = 10V, If =1mA (at Ta = -55°C) _1
Vce = 10V, If =1mA (at Ta = 125°C)_1
Collector-Emitter
Breakdown Voltage
Emitter – Collector
Breakdown
Output Saturation
Voltage
High Level Output
Current (dark current)
Input Forward Voltage
Input Reverse Break-
down Voltage
Vceo
Veco
Vce
(sat)
Iceo
Vf
Vbr
Ic = 100uA
Ie = 100Ua
If= 8mA , Ic=2.0mA
Vcc = 10V, If = 0µA
If = 10mA
Ir = 10µA
Turn on time
Turn-off time
Ton
If = 10mA, Ic = 5mA, Vcc = 10V
If = 10mA, Ic = 5mA, Vcc = 10V
9,10,11
9,10,11
5.0
100
uS
uS
Toff
Page 2
NHI 6033
Isolation Characteristics:
(at Ta = 25°C unless otherwise specified)
TEST
Capacitance,
input to output
Common Mode
Transient Immunity,
high output
Common Mode
Transient Immunity,
lo output
Isolation Voltage
SYM-
BOL
Cio
Cmh
CONDITIONS
GROUP
A SUB-
GROUP
_ 3_4
_4_5_7
4
9,10,11
LIMITS
UNITS
MIN
MAX
4
500
pF
V/µs
f = 1Mhz, Ta = 25°C
Vcm = 25v (peak)
Vcc = 5.0v, Rl = 2.0K
If = 0mA,
Vcm = 25v (peak)
Vcc = 5.0v, Rl = 2.0K
If = 0mA,
Ii-o
≤
1uA
Cml
Viso
_4_6_7
_2_4
9,10,11
500
1500
V/µs
Vdc
Notes;
_1 Ctr is defined as the ratio of the Output Collector current (Io) to the LED Forward Current ( If ), times 100%.
_2 Device is considered a two terminal device. Pins 1 and 2 are shorted together and pins 4 and 5 are shorted
together.
_3 Measured between the LED cathode and pins 4 and 5 (shorted together).
_4 Parameters shall be tested as part of the device’s initial characterization . Parameters are guaranteed to the limits
specified for all lots not specifically tested.
_5 Cmh is the maximum common mode transient to assure that the output will remain in a high logic state (Vo > 2.0V).
_6 Cml is the maximum common mode transient to assure that the output will remain in a low logic state (Vo < 0.8V).
_7 In applications where dV/dt may exceed 50,000 Vµs a series resistor must be included in the Vcc line to limit
destructively high surge currents. The recommended value, at If = 0.5mA, is 3.3K
Page 3
NHI 6033
Fig 1 Switching Time Test Circuit
Fig 2 Common Mode Test circuit
Fig 3 Switching Time Test Waveform
Fig 4 Common Mode Test Waveform
Page 4
NHI 6033
GULLWING
OPTION (-X)
0.160
PIN 1
LEADLESS
OPTION (-Z)
0.035
0.050
PIN 1
0.110 MAX
0.032
0.035
0.120
0.075 MAX
0.16
0.04
PIN 1
0.120
2.2984
0.025
TYPICAL P.C. PATTERN
Page 5
Rev October 2005
NHI 6033
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
