HCPL-7560
Optically Isolated Sigma-Delta (Σ-∆) Modulator
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
The HCPL-7560 Optically Isolated Modulator and HCPL-
0872 Digital Interface IC or digital filter together form
an isolated programmable two-chip analog-to-digital
converter. The isolated modulator allows direct mea-
surement of motor phase currents in power inverters.
In operation, the HCPL-7560 Isolated Modulator (op-
tocoupler with 3750 V
RMS
dielectric withstand voltage
rating) converts a low-bandwidth analog input into a
high-speed one-bit data stream by means of a Sigma-
Delta (Σ-∆) over-sampling modulator. This modulation
provides for high noise margins and excellent immunity
against isolation-mode transients. The modulator data
and on-chip sampling clock are encoded and transmit-
ted across the isolation boundary where they are recov-
ered and decoded into separate high-speed clock and
data channels.
Features
•
8-bit Linearity
•
200 ns Conversion Time
(Pre-Trigger Mode 2 with HCPL-0872)
•
8-bit Effective Resolution with 5µs Signal Delay
(14-bit with 102
µs)
(with HCPL-0872)
•
Fast 3
µs
Over-Range Detection (with HCPL-0872)
•
± 200 mV Input Range with Single 5 V Supply
•
5% Internal Reference Voltage Matching
•
Offset Calibration (with HCPL-0872)
•
-40°C to +85°C Operating Temperature Range
•
15 kV/µs Isolation Transient Immunity
•
Safety Approval: UL 1577, CSA and
IEC/EN/DIN EN 60747-5-2
Applications
•
Motor Phase and Rail Current Sensing
•
Data Acquisition Systems
•
Industrial Process Control
•
Inverter Current Sensing
•
General Purpose Current Sensing and Monitoring
1
8
2
Input
Curr ent
3
SIGMA-
-
DELTA
MOD./
ENCODE
7
DECODE
6
HCPL-0872
-
or
Digital Filter
MCU
or
DSP
4
5
HCPL-7560
-
NOTE: A 0.1 μF bypass capacitor must be connected between pins VDD1 and GND1 and between pins VDD2 and GND2.
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation, which may be induced by ESD.
Pin Description
ISOLATION
BOUNDARY
Symbol
V
DD1
8 V
DD2
Description
Supply voltage input (4.5 V to 5.5 V)
Positive input (
±
200mV recommended)
Negative input (normally connected to GND1)
Input ground
Supply voltage input (4.5 V to 5.5 V)
Clock output (10 MHz typical)
Serial data output
Output ground
V
DD1
V
IN+
V
IN-
GND1
1
2
3
4
SIGMA-
DELTA
MOD./
ENCODE
V
IN+
V
IN-
GND1
V
DD2
MCLK
MDAT
GND2
7 MCLK
DECODE
6
MDAT
5 GND2
SHIELD
HCPL-7560
Ordering Information
HCPL-7560 is UL Recognized with 3750 Vrms for 1 minute per UL1577.
Option
Part number
HCPL-7560
RoHS
Compliant
-000E
-300E
-500E
-060E
-360E
Non-RoHS
Compliant
No option
-300
-500
-060
-360
X
X
Package
300 mil DIP-8
X
X
X
X
X
X
X
Surface
Mount
Gull
Wing
Tape
& Reel
IEC/EN/DIN EN
60747-5-2
Quantity
50 per tube
50 per tube
1000 per reel
50 per tube
50 per tube
-560E
-560
X
X
X
X
1000 per reel
To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry.
Example 1:
HCPL-7560-560E to order product of Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/
DIN EN 60747-5-2 Safety Approval in RoHS compliant.
Example 2:
HCPL-7560 to order product of 300 mil DIP-8 package in tube packaging and non-RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
2
Package Outline Drawings
8-pin DIP Package
9.80 ± 0.25
(0.386 ± 0.010)
8
7
6
A 7560 Z
YYWW
1
1.19 (0.047) MAX.
2
3
4
1.78 (0.070) MAX.
7.62 ± 0.25
(0.300 ± 0.010)
6.35 ± 0.25
(0.250 ± 0.010)
5
OPTION CODE
DATE CODE
3.56 ± 0.13
(0.140 ± 0.005)
4.70 (0.185) MAX.
0.51 (0.020) MIN.
2.92 (0.115) MIN.
0.20 (0.008)
0.33 (0.013)
1.080 ± 0.320
(0.043 ± 0.013)
0.65 (0.025) MAX.
2.54 ± 0.25
(0.100 ± 0.010)
5˚ TYP.
DIMENSIONS IN MILLIMETERS AND (INCHES).
NOTE: FLOATING LEAD PROTUSION IS 0.5 mm (20 mils) MAX.
* MARKING CODE LETTER FOR OPTION NUMBERS
"V" = OPTION 060
OPTION NUMBERS 300 AND 500 NOT MARKED.
NOTE: INITIAL OR CONTINUED VARIATION IN THE COLOR OF THE HCPL-7560’S WHITE MOLD COMPOUND IS NORMAL AND DOES NOT
AFFECT DEVICE PERFORMANCE OR RELIABILITY.
8-pin Gull Wing Surface Mount Option 300
LAND PATTERN RECOMMENDATION
9.80 ± 0.25
(0.386 ± 0.010)
8
7
6
5
1.02 (0.040)
6.350 ± 0.25
(0.250 ± 0.010)
10.9 (0.430)
MOLDED
1
2
3
4
1.27 (0.050)
1.780
(0.070)
MAX.
9.65 ± 0.25
(0.380 ± 0.010)
7.62 ± 0.25
(0.300 ± 0.010)
3.56 ± 0.13
(0.140 ± 0.005)
2.0 (0.080)
1.19
(0.047)
MAX.
0.255 (0.075)
0.010 (0.003)
1.080 ± 0.320
(0.043 ± 0.013)
2.540
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
TOLERANCES (UNLESS OTHERWISE SPECIFIED):
0.51 ± 0.130
(0.020 ± 0.005)
0.635 ± 0.25
(0.025 ± 0.010)
12
˚
NOM.
xx.xx = 0.01
xx.xxx = 0.005
LEAD COPLANARITY
MAXIMUM: 0.102 (0.004)
NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.
3
Solder Reflow Temperature Profile
300
PREHEATING RATE 3˚C + 1˚C/-0.5˚C/SEC.
REFLOW HEATING RATE 2.5˚C ± 0.5˚C/SEC.
PEAK
TEMP.
245˚C
PEAK
TEMP.
240˚C
200
TEMPERATURE (˚C)
160˚C
150˚C
140˚C
PEAK
TEMP.
230˚C
2.5˚C ± 0.5˚C/SEC.
30
SEC.
30
SEC.
SOLDERING
TIME
200˚C
3˚C + 1˚C/-0.5˚C
100
PREHEATING TIME
150˚C, 90 + 30 SEC.
50 SEC.
TIGHT
TYPICAL
LOOSE
ROOM
TEMPERATURE
0
0
50
100
TIME (SECONDS)
Note: Use of non-chlorine-activated fluxes is highly recommended.
150
200
250
Recommended Pb-Free IR Profile
tp
T
p
TEMPERATURE (˚C)
T
L
T
smax
T
smin
t
s
PREHEAT
60 to 180 SEC.
25
t 25˚C to PEAK
TIME (SECONDS)
NOTES:
THE TIME FROM 25 C to PEAK TEMPERATURE = 8 MINUTES MAX.
T
smax
= 200˚C, T
smin
= 150˚C
Note: Use of non-chlorine-activated fluxes is highly recommended.
t
L
60 to 150 SEC.
260 +0/-5˚C
217˚C
RAMP-UP
3˚C/SEC. MAX.
150 - 200
˚C
RAMP-DOWN
6˚C/SEC. MAX.
TIME WITHIN 5˚C of ACTUAL
PEAK TEMPERATURE
20-40 SEC.
4
Regulatory Information
The HCPL-7560 has been approved by the following organizations:
IEC/EN/DIN EN 60747-5-2
Approved under:
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01.
UL
Approval under UL 1577, component recognition program up to V
ISO
= 3750 V
RMS
. File E55361.
CSA
Approval under CSA Component Acceptance Notice #5, File CA 88324.
IEC/EN/DIN EN 60747-5-2 Insulation Characteristics
[1]
Description
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage
≤
300 Vrms
for rated mains voltage
≤
450 Vrms
for rated mains voltage
≤
600 Vrms
Climatic Classification
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b
[2]
V
IORM
x 1.875=V
PR
, 100% Production Test with t
m
=1 sec,
Partial discharge < 5 pC
Input to Output Test Voltage, Method a
[2]
V
IORM
x 1.5=V
PR
, Type and Sample Test, t
m
=60 sec,
Partial discharge < 5 pC
Highest Allowable Overvoltage
(Transient Overvoltage t
ini
= 10 sec)
Safety-limiting values - maximum values allowed in the event of a failure,
also see Figure 13.
Case Temperature
Input Current
[3]
Output Power
[3]
Insulation Resistance at T
S
, V
IO
= 500 V
V
IORM
V
PR
Symbol
HCPL-7560
I - IV
I - III
I - II
40/85/21
2
891
1670
V
peak
V
peak
Unit
V
PR
V
IOTM
1336
6000
V
peak
V
peak
T
S
I
S, INPUT
P
S, OUTPUT
R
S
175
400
600
>10
9
°C
mA
mW
W
Notes:
1. Insulation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits within the
application. Surface Mount Classifications is Class A in accordance with CECC00802.
2. Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section, (IEC/
EN/DIN EN 60747-5-2) for a detailed description of Method a and Method b partial discharge test profiles.
3. Refer to the following figure for dependence of P
S
and I
S
on ambient temperature.
5
ST传感器与低功耗无线技术论坛
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
