The documentation and process conversion
measures necessary to comply with this
revision shall be completed by 08 October 1999.
INCH-POUND
MIL-PRF-19500/127N
09 July 1999
SUPERSEDING
MIL-S-19500/127M
14 March 1994
PERFORMANCE SPECIFICATION SHEET
SEMICONDUCTOR DEVICES, DIODE, SILICON, VOLTAGE REGULATOR,
TYPES 1N4370A-1 THROUGH 1N4372A-1, AND 1N746A-1 THROUGH 1N759A-1, 1N4370AUR-1 THROUGH 1N4372AUR-1 AND
1N746AUR-1 THROUGH 1N759AUR-1, 1N4370C-1 THROUGH 1N4372C-1, AND 1N746C-1 THROUGH 1N759C-1, 1N4370CUR-1
THROUGH 1N4372CUR-1 AND 1N746CUR-1 THROUGH 1N759CUR-1, 1N4370D-1, THROUGH 1N4372D-1, AND 1N746D-1
THROUGH 1N759D-1, 1N4370DUR-1 THROUGH 1N4372DUR-1 AND 1N746DUR-1 THROUGH 1N759DUR-1,
JAN, JANTX, JANTXV, JANHC, AND JANKC
JANS level (see 6.3).
This specification is approved for use by all Departments
and Agencies of the Department of Defense.
1. SCOPE
1.1 Scope. This specification covers the performance requirements for 500 milliwatt, silicon, voltage regulator diodes with voltage
tolerances of 5, 2, and 1 percent. Three levels of product assurance are provided for each device type as specified in MIL-PRF-19500.
Two level of product assurance is provided for die.
1.2 Physical dimensions. See 3.3 and figure 1 (similar to DO-35) and figure 2 (similar to DO-213AA), and figures 3 and 4 for die.
1.3 Maximum ratings. Maximum ratings are as shown in column 4 table II herein and as follows:
P
T
= 500 mW, (DO-35) at T
L
= +50
°
C, L = .375 inch (9.53 mm); both ends of case or diode body to heat sink at
L = .375 inch (9.53 mm). Derate I
Z
to 0.0 mA dc at +175
°
C.
-65
°
C
≤
T
J
≤
+175
°
C; -65
°
C
≤
T
STG
≤
+175
°
C
P
T
= 500 mW, (DO-213AA) at T
EC
= +125
°
C, derate to 0 at +175
°
C.
1.4 Primary electrical characteristics. Primary electrical characteristics are as shown in columns 2, 9, 12, and 14 table II herein and as
follows:
2.4 V dc
≤
V
Z
≤
12 v dc
1N4370A-1 through 1N4372A-1 and 1N746A-1 through 1N759A-1 are
±
5 percent voltage tolerance.
1N4370C-1 through 1N4372C-1 and 1N746C-1 through 1N759C-1 are
±
2 percent voltage tolerance.
1N4370D-1 through 1N4372D-1 and 1N746D-1 through 1N759D-1 are
±
1 percent voltage tolerance.
Thermal resistance:
R
θ
JL
= 250
°
C/W maximum at L = .375 inch (9.53 mm) (D0-35).
R
θ
JEC
= 100
°
C/W maximum. Junction to end-caps (D0-213AA).
Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document
should be addressed to: Commander, Defense Supply Center Columbus, ATTN: DSCC-VAC, 3990 East Broad St., Columbus, OH
43216-5000, by using the addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this
document or by letter.
AMSC N/A
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
FSC 5961
MIL-PRF-19500/127N
Symbol
Inches
Min
BD
BL
LD
LL
LU
0.055
0.120
0.018
1.000
Max
0.090
0.200
0.023
1.500
0.050
Dimensions
Millimeters
Min
1.40
3.05
0.46
25.40
Max
2.29
5.08
0.56
38.10
1.27
Notes
3
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. Symbol BD shall be measured at the largest diameter.
4. Within LU lead diameter may vary to allow for flash, lead finish build-up, and minor irregularities other than heat slugs.
5. In accordance with ANSI Y14.5M, diameters are equivalent to
φ
X symbology.
FIGURE 1. Physical dimensions for types 1N4370A-1 through 1N4372A-1, 1N4370C-1 through 1N4372C-1, 1N4370D-1 through
1N4372D-1, 1N746A-1 through 1N759A-1, 1N746C-1 through 1N759C-1, and 1N746D-1 through 1N759D-1 (D0-35).
2
MIL-PRF-19500/127N
Symbol
Inches
Min
BL
BD
ECT
S
.130
.063
.016
.001 min
Max
.146
.067
.022
Dimensions
Millimeters
Min
3.30
1.60
0.41
0.03 min
Max
3.70
1.70
0.55
NOTES:
1. Dimensions are in inches.
2. Metric equivalent are given for general information only.
3. In accordance with ANSI Y14.5M, diameters are equivalent to
φ
X symbology.
FIGURE 2. Physical dimensions for types 1N4370AUR-1 through 1N4372AUR-1, 1N4370CUR-1 through 1N4372CUR-1,
1N4370DUR-1 through 1N4372DUR-1, 1N746AUR-1 through 1N759AUR-1, 1N746CUR-1 through 1N759CUR-1,
and 1N746DUR-1 through 1N759DUR-1 (D0-213AA).
3
MIL-PRF-19500/127N
(A – version)
Ltr
Inches
A
B
Min
.021
.013
Max
.025
.017
Dimensions
Millimeters
Min
Max
0.53
0.63
0.33
0.43
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. The physical characteristics of the die thickness are .010
±
.002 (0.25 mm). Metallization is top = (anode)-AL,
back: (cathode)-AU. AL thickness = 25000 Å minimum, AU thickness = 4000 Å minimum.
4. Circuit layout data: For zener operation, cathode must be operated positive with respect to anode.
FIGURE 3. Physical dimensions (JANHCA and JANKCA die dimensions).
4
MIL-PRF-19500/127N
(B – version)
Ltr
Inches
A
B
Min
.024
.017
Max
.028
.021
Dimensions
Millimeters
Min
Max
0.61
0.71
0.43
0.53
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. The physical characteristics of the die thickness are .010
±
.002 (0.25 mm). Metallization is top = (anode)-AL,
back: (cathode)-AU. AL thickness = 40000 Å minimum, AU thickness = 5000 Å minimum.
4. Circuit layout data: For zener operation, cathode must be operated positive with respect to anode.
FIGURE 4. Physical dimensions (JANHCB and JANKCB die dimensions) - Continued.
5
微控制器 MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
