256Mb: x4, x8, x16
SDRAM 3.3V
SYNCHRONOUS DRAM
Features:
•
•
•
•
•
•
•
•
•
•
•
Intel PC133 (3-3-3) compatible
Fully synchronous; all signals registered on positive
edge of system clock
Internal pipelined operation; column address can be
changed every clock cycle
Internal banks for hiding row access precharge time
Programmable burst lengths: 1, 2, or 4 using
Interleaved Burst Addressing
Auto Precharge and Auto Refresh modes
64ms, 8,192-cycle refresh
Self Refresh mode option
1
LVTTL-compatible inputs and outputs
Single +3.3V ±0.3V power supply
The x16 devices are optimized for both single and
dual rank DIMM applications. The x8 devices are
optimized for single rank DIMM applications. The
x4 devices are optimized for registered single-rank
DIMM applications
Options:
Family:
SpecTek Memory
Configuration:
64 Meg x 4 (16 Meg x 4 x 4 banks)
32 Meg x 8 (8 Meg x 8 x 4 banks)
16 Meg x 16 (4 Meg x 16 x 4 banks)
Design ID
SDRAM 256 Megabit Design
(Call SpecTek Sales for details on
availability of “x” placeholders)
Voltage and Refresh:
3.3V, Auto Refresh, 8K refresh
3.3V, Self or Auto Refresh, 8K refresh
Package Types:
54-pin plastic TSOP (400 mil)
60-ball FBGA (8mm x 16mm)
60-ball FBGA (11mm x 13mm)
Timing Types:
PC133 (3-3-3)
Part number example:
(For part numbers prior to December
2004, refer to
page 10
for decoding.)
Designation:
SAA
64M4
32M8
16M16
Yx6x
NOTES: 1. Only when specified. Consult Sales
2. Not available in x16 configuration
L8
M8
1
TK
FB
2
FC
2
-75A
SAA32M8 Y16AL8TK-75A
General Description:
The 256Mb SDRAM is a high-speed CMOS, dynamic
random-access memory containing 268,435,456 bits.
Each is internally configured as a quad-bank DRAM.
Read and write accesses to the SDRAM are burst
oriented; accesses start at a selected location and continue
for a programmed number of locations in a programmed
sequence. Accesses begin with the registration of an
ACTIVE command, which is then followed by a READ
or WRITE command. The address bits registered
coincident with the ACTIVE command are used to select
the bank and row to be accessed (BA0, BA1 select the
bank; A0-A12 select the row). The address bits registered
PDF: 09005aef80457d0d / Source: 09005aef8043e207
256Mb SDRAM
Rev: 11/23/2004
1
www.spectek.com
SpecTek reserves the right to change products or
specifications without notice.
©
2001, 2002, 2004 SpecTek
256Mb: x4, x8, x16
SDRAM 3.3V
coincident with the READ or WRITE commands are used
to select the starting column location for the burst access.
The SDRAM provides for programmable READ or
WRITE burst lengths of 1, 2, or 4 locations with burst
terminate option using the Burst Interleaved Addressing
mode only. An AUTO PRECHARGE function may be
enabled to provide a self-timed row precharge that is
initiated at the end of the burst sequence.
The 256Mb SDRAM uses an internal pipelined
architecture to achieve high-speed operation. This
architecture is compatible with the 2n rule of prefetch
architectures, but it also allows the column address to be
changed on every clock cycle to achieve a high-speed,
fully random access. Precharging one bank while
accessing one of the other three banks will hide the
precharge cycles and provide seamless high-speed,
random-access operation.
The 256Mb SDRAM is designed to operate in 3.3V,
low-power memory systems. An auto refresh mode is
provided, along with a power-saving power-down mode.
All inputs and outputs are LVTTL-compatible.
SDRAMs offer substantial advances in DRAM
operating performance, including the abilities to
synchronously burst data at a high data rate with
automatic column-address generation, to interleave
between internal banks in order to hide precharge time,
and to randomly change column addresses on each clock
cycle during a burst access.
The x8 devices are optimized for single bank DIMM
applications. The x16 devices are available for both
single and dual bank DIMM applications. The x4 devices
are optimized for registered single-bank DIMM
applications.
CAPACITANCE:
(Note 2)
Parameter
Input Capacitance: CLK
Input Capacitance: All other input-only pins
Input/Output Capacitance: DQs
Symbol
C
I1
C
I2
C
IO
Min
2.5
2.5
4.0
Max
3.5
3.8
6.0
Units
pF
pF
pF
NOTES
29
30
31
____________________________________________
Disclaimer:
Except as specifically provided in this document, SpecTek
makes no warranties, expressed or implied, including, but not
limited to, any implied warranties of merchantability or fitness for
a particular purpose.
Any claim against SpecTek must be made within one year
from the date of shipment from SpecTek, and SpecTek has no
liability thereafter. Any liability is limited to replacement of the
defective items or return of amounts paid for defective items (at
buyer’s election). In no event will SpecTek be responsible for
special, indirect, consequential or incidental damages, even if
SpecTek has been advised for the possibility of such damages.
SpecTek’s liability from any cause pursuant to this specification
shall be limited to general monetary damages in an amount not
to exceed the total purchase price of the products covered by
this specification, regardless of the form in which legal or
equitable action may be brought against SpecTek.
____________________________________
ABSOLUTE MAXIMUM RATINGS:
Voltage on Vdd Supply relative to Vss
Operating Temperature T
A
(Ambient)
Storage Temperature
Power Dissipation
Short Circuit Output Current
-1 to +4.6V
+25° to +70
°C
-55° to +150
°C
1W
50 mA
Stresses beyond these may cause permanent damage to the
device. This is a stress rating only and functional operation of
the device at or beyond these conditions is not implied.
Exposure to these conditions for extended periods may affect
reliability.
PDF: 09005aef80457d0d / Source: 09005aef8043e207
256Mb SDRAM
Rev: 11/23/2004
2
www.spectek.com
SpecTek reserves the right to change products or
specifications without notice.
©
2001, 2002, 2004 SpecTek
256Mb: x4, x8, x16
SDRAM 3.3V
DC ELECTRICAL CHARACTERISTICS AND RECOMMENDED OPERATING CONDITIONS:
(Notes: 1, 5, 6
:
Vdd = 3.3V
±
10%V, Temp.
=
25° to 70
°C)
Parameter
Supply Voltage
Input High (Logic 1) Voltage, All inputs
Input Low (Logic 0) Voltage, All inputs
Input Leakage Current Any input = 0V < VIN < Vdd All other pins not under test =
0V
Output Leakage Current DQs are disabled; 0V < VOUT < VddQ
Output High Voltage (I
OUT
= -4 mA)
Output Low Voltage (I
OUT
= 4 mA)
Symbol
Vdd/Vddq
V
IH
V
IL
I
I
I
OZ
V
OH
V
OL
Min
3.0
2.2
-0.3
-10
-10
2.4
Max
3.6
Vdd + .3
0.8
10
10
0.4
Units
V
V
V
µA
µA
V
V
Units
22
22
Idd OPERATING CONDITIONS AND MAXIMUM LIMITS
(Notes: 1, 5, 6, 11, 13
:
Vdd = 3.3V
±
10%V, Temp.
=
25° to 70
°C)
Supply Current
OPERATING CURRENT:
ACTIVE mode, burst = 1, READ or WRITE, tRC > tRC
(MIN), one bank active, CL=3
STANDBY CURRENT:
POWER-DOWN mode, CKE = LOW,
Standard parts
no accesses in progress
Self refresh parts
STANDBY CURRENT:
CS# = HIGH, CKE = HIGH, all banks idle
STANDBY CURRENT:
CS# = HIGH, CKE = HIGH, all banks active after tRCD
met, no accesses in progress.
OPERATING CURRENT:
BURST mode after tRCD met, continuous burst, READ,
WRITE, all banks active, CL=3
AUTO REFRESH CURRENT
tRC > tRC (MIN)
CL = 3
AUTO REFRESH CURRENT
tRC= 7.8µs
SELF REFRESH CURRENT
(Self refresh parts only, part M)
CL = 3
Symbol
Idd1
Idd2
Idd2
Idd3
Idd4
Idd5
Idd6
Idd7
Idd8
-75A
165
9
3
75
75
165
265
50
3
Units
mA
mA
mA
mA
mA
mA
mA
mA
mA
3, 18, 19,
32
3, 12, 18,
19, 33
3, 12, 18,
19, 33
Notes
3, 19, 32
32
32
3, 12, 19,
32
PDF: 09005aef80457d0d / Source: 09005aef8043e207
256Mb SDRAM
Rev: 11/23/2004
3
www.spectek.com
SpecTek reserves the right to change products or
specifications without notice.
©
2001, 2002, 2004 SpecTek
256Mb: x4, x8, x16
SDRAM 3.3V
AC ELECTRICAL CHARACTERISTICS:
(Notes: 5, 6, 8, 9, 11. Vdd = 3.3V
±
10%V, Temp. = 25° to 70°C)
AC CHARACTERISTICS
PARAMETER
Access time from CLK (positive edge) CL = 3
Access time from CLK (positive edge) CL = 2
Address hold time
Address setup time
CLK high level width
CLK low level width
Clock cycle time CL = 3
CKE hold time
CKE setup time
CS#, RAS#, CAS#, WE#, DQM hold time
CS#, RAS#, CAS#, WE#, DQM setup time
Data-in hold time
Data-in setup time
Data-out high impedance time
Data-out low impedance time
Data-out hold time
ACTIVE to PRECHARGE command period
AUTO REFRESH to ACTIVE command period
ACTIVE to READ or WRITE delay
Refresh period (8,192 cycles)
PRECHARGE command period
ACTIVE bank A to bank B command period
Transition time
Write recovery time
Exit SELF REFRESH to ACTIVE command
SYMBOL
tAC
tAC
tAH
tAS
tCH
tCL
tCK
tCKH
tCKS
tCMH
tCMS
tDH
tDS
tHZ
tLZ
tOH
tRAS
tRC
tRCD
tREF
tRP
tRRD
tT
tWR
tXSR
-75A
MIN
-75A
MAX
5.4
N/A
UNITS
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
ns
ns
ns
ns
tCK
NOTES
27
0.8
1.5
2.5
2.5
7.5
0.8
1.5
0.8
1.5
0.8
1.5
9
1
2.7
44
60
22.5
22.5
15
0.3
20
8
23
10
16K
64
2
7
15
20
AC ELECTRICAL CHARACTERISTICS:
(Notes: 5, 6, 7, 8, 9, 11. Vdd = 3.3V
±
10%V, Temp. = 25° to 70°C)
PARAMETER
READ/WRITE command to READ/WRITE command
CKE to clock disable or power down entry mode
CKE to clock enable or power down exit setup
DQM to input data delay
WRITE command to input data delay
Data-in to ACTIVATE command w/ Auto precharge
Data-in to precharge
Last data-in to precharge command
LOAD MODE REGISTER command to command
Data-out to high impedance from precharge
SYMBOL
tCCD
tCKED
tPED
tDQD
tDWD
tDAL
tDPL
tRDL
tMRD
tROH
-75A
1
1
1
0
0
5
2
2
2
3
UNITS
tCK
tCK
tCK
tCK
tCK
tCK
tCK
tCK
tCK
tCK
NOTES
17
14
14
17
17
15, 21
16, 21
16,21
26
17
PDF: 09005aef80457d0d / Source: 09005aef8043e207
256Mb SDRAM
Rev: 11/23/2004
4
www.spectek.com
SpecTek reserves the right to change products or
specifications without notice.
©
2001, 2002, 2004 SpecTek
256Mb: x4, x8, x16
SDRAM 3.3V
NOTES
1.
2.
3.
4.
5.
6.
All voltages referenced to V
SS
.
This parameter is sampled. V
DD
, V
DD
Q = +3.3V; F =
1 MHz, T
A
= 25°C; pin under test biased at 1.4V.
I
DD
is dependent on output loading and cycle rates.
Specified values are obtained with minimum cycle time
and the outputs open.
Enables on-chip refresh and address counters.
The minimum specifications are used only to indicate
cycle time at which proper operation over the full
temperature range is ensured; (25°C ≤T ≤+70°C).
A
An initial pause of 100µs is required after power-up,
followed by two AUTO REFRESH commands, before
proper device operation is ensured. (V
DD
and V
DD
Q
must be powered up simultaneously. V
SS
and V
SS
Q must
be at same potential.) The two AUTO REFRESH
command wake-ups should be repeated any time the
t
REF refresh requirement is exceeded.
AC characteristics assume
t
T = 1ns.
In addition to meeting the transition rate specification,
the clock and CKE must transit between V
IH
and V
IL
(or
between V
IL
and V
IH
) in a monotonic manner.
Outputs measured at 1.5V with equivalent load:
14. Timing actually specified by
t
CKS; clock(s)
specified as a reference only at minimum cycle rate.
15. Timing actually specified by
t
WR plus
t
RP; clock(s)
specified as a reference only at minimum cycle rate.
16. Timing actually specified by
t
WR.
17. Required clocks are specified by JEDEC
functionality and are not dependent on any timing
parameter.
18. The I
DD
current will increase or decrease
proportionally according to the amount of frequency
alteration for the test condition.
19. Address transitions average one transition every two
clocks.
20. CLK must be toggled a minimum of two times
during this period.
21. Based on
t
CK = 10ns for –75A.
22. V
IH
overshoot: V
IH
(MAX) = V
DD
Q + 2V for a pulse
width
≤
3ns, and the pulse width cannot begreater
than one third of the cycle rate. V
IL
undershoot: V
IL
(MIN) = -2V for a pulse width ≤3ns.
23. The clock frequency must remain constant (stable
clock is defined as a signal cycling within timing
constraints specified for the clock pin) during access
or precharge states (READ, WRITE, including
t
WR,
and PRECHARGE commands). CKE may be used
to reduce the data rate.
24. Auto precharge mode only. The precharge timing
budget (
t
RP) begins 7.5ns for –75A after the first
clock delay, after the last WRITE is executed. May
not exceed limit set for precharge mode.
25. Precharge mode only.
26. JEDEC and PC100 specify three clocks.
27.
t
AC for –75A at CL = 3 with no load is 4.6ns and is
guaranteed by design.
28. Parameter guaranteed by design.
29. PC100 specifies a maximum of 4pF.
30. PC100 specifies a maximum of 5pF.
31. PC100 specifies a maximum of 6.5pF.
32. For –75A, CL = 3 and
t
CK = 7.5ns.
33. CKE is HIGH during refresh command period
t
RFC
(MIN) else CKE is LOW. The I
DD
6 limit is actually
a nominal value and does not result in a fail value.
7.
8.
9.
10.
t
HZ defines the time at which the output achieves the
open circuit condition; it is not a reference to V
OH
or
V
OL
. The last valid data element will meet
t
OH before
going High-Z.
11. AC timing and I
DD
tests have V
IL
= 0V and V
IH
= 3V,
with timing referenced to 1.5V crossover point. If the
input transition time is longer than 1 ns, then the timing
is referenced at V
IL
(MAX) and V
IH
(MIN) and no
longer at the ISV crossover point.
12. Other input signals are allowed to transition no more
than once every two clocks and are otherwise at valid
V
IH
or V
IL
levels.
13.
I
DD
specifications are tested after the device is properly
initialized.
PDF: 09005aef80457d0d / Source: 09005aef8043e207
256Mb SDRAM
Rev: 11/23/2004
5
www.spectek.com
SpecTek reserves the right to change products or
specifications without notice.
©
2001, 2002, 2004 SpecTek
单片机
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
