Product
Specification
108-2043
11Mar11 Rev D
Ultra-Fast Fully Insulated FASTON* Receptacle Terminals
1.
1.1.
SCOPE
Content
This specification covers the perform ance requirem ents for Ultra-Fast fully insulated FASTON*
receptacle term inals. These term inals consist of a FASTON receptacle body enclosed in a fully
insulated housing. They m ate with FASTON tabs on devices used in hom e entertainm ent centers,
business m achines, copying equipm ent, com puter peripherals, appliances and other com m ercial
equipm ent
1.2.
Qualification
W hen tests are perform ed on the subject product line, procedures specified in Figure 1 shall be used.
All inspections shall be perform ed using the applicable inspection plan and product drawing.
2.
APPLICABLE DOCUM ENTS
The following docum ents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the docum ent applies. In the event of conflict between the
requirem ents of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirem ents of this specification and the referenced docum ents,
this specification shall take precedence.
2.1.
TE Connectivity (TE) Docum ents
!
!
!
2.2.
109-1: General Requirem ents for Test Specifications
109 Series: Test Specifications as indicated in Figure 1
114-2123: Application Specification
Com m ercial Standards
!
!
!
CSA C22.2 No 153: Quick-Connect Term inals
DIN VDE 0627: Connectors and Plug-And-Socket Devices
UL 310: Quick-Connect Term inals, Standard for
3.
3.1.
REQUIREM ENTS
Design and Construction
Product shall be of the design, construction and physical dim ensions specified on the applicable product
drawing.
3.2.
Materials
!
!
!
!
Receptacle body: Brass or phosphor bronze, tin plated
Housing: Nylon type 6/6, UL 94V-2
Tabs (for test purposes): Brass, tem per 2, CDA alloy
W ire (for test purposes): Com plies with UL 310 Paragraph 7, 600 Volt rating
©2011 Tyco Electronics Corporation, | Indicates change
a TE Connectivity Ltd. Company
*Trademark
All Rights Reserved
TE logo is a trademark.
For latest revision, visit our website at www.te.com/documents.
For Regional Customer Service, visit our website at www.te.com
Other products, logos, and company names might be trademarks of their respective owners.
1 of 5
LOC B
108-2043
3.3.
Ratings
!
!
3.4.
Voltage: 600 volts AC m axim um
Operating Tem perature: 105°C m axim um
Perform ance and Test Description
Product is designed to m eet the electrical, m echanical and environm ental perform ance requirem ents
specified in Figure 1.
3.5.
Test Requirem ents and Procedures Sum m ary
Test Description
Requirem ent
Meets requirem ents of product
drawing and Application Spec 114-
2123.
ELECTRICAL
Procedure
TE Spec 109-1.
Visual, dim ensional and functional
per applicable inspection plan.
Exam ination of Product.
Dielectric W ithstanding Voltage,
Test Condition A.
Dielectric W ithstanding Voltage,
Test Condition C.
Dielectric W ithstanding Voltage,
Receptacle, Tab Entry Position.
No breakdown or flashover when
3400 volts AC are applied for 1
m inute.
No breakdown or flashover at rear
of term inal when 3000 volts AC are
applied for 1 m inute.
Term inal
Applied
Size
Voltage (volts AC)
250
1000
187
1000
110
600
No breakdown or flashover, 1
m inute hold.
W ire Size
Current (am peres)
(AW G)
.110
Others
26
1
1
24
2
2
22
2
3
20
3
4
18
4
7
16
5
10
14
8
15
12
–
20
10
–
24
20°C m axim um tem perature rise.
Figure 1 (continued)
UL 310, 600 Volt Rating.
Test wired term inals in Num ber 12
lead shot.
UL 310, 600 Volt Rating.
Test on flat m etal plate.
See Figure 4.
TE Spec 109-29-1.
Test wired term inals on a flat m etal
plate.
See Figure 5.
Heating (Tem perature Rise).
UL 310.
Stabilize at specified current and
m easure tem perature rise.
Rev D
2 of 5
108-2043
Test Description
Heat Cycling (Current Cycling).
Requirem ent
W ire Size
Current (am peres)
(AW G)
.110
Others
26
2
2
24
4
4
22
4
6
20
6
8
18
8
14
16
10
20
14
15
30
12
–
40
10
–
48
65°C m axim um tem perature rise.
Ä
Tem perature rise between 24 and
500 cycles shall not exceed 15°C
on any conductor.
MECHANICAL
Pull Out (Crim p Tensile).
W ire Size
Tensile
(AW G)
(Lbs m inim um )
26
4
24
6
22
10
20
16
Above values are less than
m axim um withdrawal force. See
Figure 2.
18
20
16
30
14
60
12
70
10
80
UL 310.
Apply a direct and gradual pull at a
rate of 1 inch per m inute, 1 m inute
hold at specified load.
Procedure
UL 310.
Subject sam ples to 500 current
cycles of 45 m inutes ON and 15
m inutes OFF.
Secureness of Insulation
(Unassem bled).
No separation of the insulation from UL 310.
the term inal body.
Subject unwired term inals to a 3
pound pull between the insulation
and term inal for 1 m inute.
No separation of the insulation from UL 310.
the term inal body.
Subject wired term inals to a 6
pound pull between the insulation
and term inal for 1 m inute.
See Figure 2.
UL 310.
Engage and disengage term inals
and tabs 6 tim es.
Secureness of Insulation
(Assem bled).
Engagem ent-Disengagem ent
(Engaging-Separating).
ENVIRONMENTAL
Heat Age, 136°C.
Meet Dielectric W ithstanding
Voltage, Test Condition A; and
Secureness of Insulation
(assem bled and unassem bled).
Meet Dielectric W ithstanding
Voltage, Test Condition A.
UL 310.
Subject term inals to 136°C for 7
days.
UL 310.
Subject unwired term inals to 100EC
for 7 days followed by 85% RH at
30EC for 24 hours.
Heat Age/Hum idity.
Figure 1 (end)
Rev D
3 of 5
108-2043
Force (pounds)
First
First
Tab Size
Term inal Insertion
W ithdrawal
(Plain Brass) Plating Individual Individual Average Individual
(m ax)
(m ax)
(m in)
(m in)
.250
.205/.187
.110
Tin
17
15
12
17
20
14
5
5
3
3
3
2
Sixth
W ithdrawal
Average
(m in)
4
3
2
Individual
(m in)
3
2
1
Figure 2
Engagem ent and Disengagem ent Forces
3.6.
Term inal Tests and Sequences
Test Group (a)
Test or Exam ination
1
2
3
4
5
6
7
8
9
10
11
12
Test Sequence (b)
Exam ination of Product
Dielectric W ithstanding Voltage,
Test Condition A
Dielectric W ithstanding Voltage,
Test Condition C
Dielectric W ithstanding Voltage,
Receptacle, Tab Entry Position
Heating (Tem perature Rise)
Heat Cycling (Current Cycling)
Pull Out (Crim p Tensile)
Secureness of Insulation
(Unassem bled)
Secureness of Insulation
(Assem bled)
Engagem ent-Disengagem ent
(Engaging-Separating)
Heat Age, 136EC
Heat Age/Hum idity
NOTE
(a)
(b)
(c)
2
2
2
2
2
2
3
3
2
2
3
3
3(c)
2
1
1
2
1
3
1
3(c)
2
2
1
1
1
1
1
1
1
1
See paragraph 4.1.A.
Numbers indicate sequence in which tests are performed.
Uncrimped terminals and wires in test groups 4 and 11 shall be conditioned in the
environments indicated. After conditioning, each sample is crimped to the appropriate
wire and the electrical or mechanical test is performed.
Figure 3
Rev D
4 of 5
108-2043
4.
4.1.
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
Sam ple Selection
Term inals and tabs shall be prepared in accordance with applicable Instruction Sheets and shall
be selected at random from current production. Test groups 1, 2, 3 and 4 shall each consist of 20
sam ples of each wire size and term inal type per group. Test groups 5, 6, 7, 8, 9, 10, 11 and 12
shall each consist of 20 sam ples of each term inal type per group. All sam ples to be term inated
shall be crim ped to appropriate tin plated test conductors.
B.
Test Sequence
Qualification inspection shall be verified by testing sam ples as specified in Figure 3.
C.
Acceptance
1.
Requirem ents put on the test sam ples, as indicated in the Requirem ents portion of Figure 1,
exist as either the upper or lower statistical tolerance lim it (95% confidence, 98% reliability).
All sam ples tested in accordance with this specification shall m eet the stated tolerance lim it.
Failures attributed to equipm ent, test setup or operator deficiencies shall not disqualify the
product. W hen product failure occurs, corrective action shall be taken and sam ples
resubm itted for qualification.
2.
4.2.
Quality Conform ance Inspection
The applicable inspection plan will specify the sam pling acceptable quality level to be used. Dim ensional
and functional requirem ents shall be in accordance with the applicable product drawing and this
specification.
4.3.
Certification
This product has been recognized under the Com ponent Recognition Program of Underwriters
Laboratories Inc., Electrical File Num ber E-66717 and certified by Canadian Standards Association File
Num bers LR-7189. Also, VDE Testing and Certification Institute, Reference No. 4751_1431_1047.
Figure 4
Metal Plate Test Fixture
Figure 5
Tab, Receptacle Entry Position
Rev D
5 of 5
Microchip MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
