RHFL4913A
Datasheet
Rad-hard adjustable positive voltage regulator
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Operating input voltage from 3 V to 12 V
Adjustable output voltage
3 A maximum guaranteed output current in SMD5C package, 2 A in FLAT-16
Very low dropout voltage: 350 mV typ. @ 400 mA
Embedded overtemperature and overcurrent protection
Adjustable overcurrent limitation
Very low noise: 40 µV
RMS
(10 Hz-100 kHz)
Output overload monitoring/signalling
Inhibit (ON/OFF) TTL-compatible control
Programmable output short-circuit current
Remote sensing operation
Low quiescent current: 1.5 mA typ. @ no load, 150 µA in shutdown
Rad-hard: guaranteed up to 300 krad Mil Std 883E Method 1019.6 high dose
rate and 0.01 rad/s in ELDRS conditions
Heavy ion, SEL immune.
FLAT-16
SMD5C:
5-connection SMD
Description
The
RHFL4913A
is a high-performance adjustable positive voltage regulator, able to
provide 2 A of maximum current in FLAT-16 package (3 A in the SMD5C package)
from an input voltage ranging from 3 V to 12 V, with a typical dropout voltage of 350
mV.
The
RHFL4913A
features exceptional radiation performances. It is tested in
accordance with Mil Std 883E Method 1019.6, in ELDRS conditions. The device is
available in the FLAT-16 and the SMD5C hermetic ceramic package, and the QML-V
die is suitable for harsh environments. It operates with an input supply of up to 12 V.
The
RHFL4913A
is QML-V qualified, DSCC SMD #5962F02524.
Maturity status link
RHFL4913A
DS3625
-
Rev 21
-
February 2019
For further information contact your local STMicroelectronics sales office.
www.st.com
RHFL4913A
Pin configuration
2
Pin configuration
Figure 2.
Pin configuration (top view for FLAT-16, bottom view for SMD5C)
FLAT-16
SMD5C
AMG081120161301MT
Table 1.
Pin description
Pin name
V
O
V
I
GND
I
SC
OCM
INHIBIT
ADJ
NC
FLAT-16
(1)
1, 2, 6, 7
3, 4, 5
13
8
10
14
15
9, 11, 12, 16
3
2
SMD5C
(2)
1
4
5
1. The upper metallic package lid and the bottom metallization are neither connected to regulator die nor to
package terminals, hence electrically floating.
2. The upper metallic package lid is neither connected to regulator die nor to package terminals, hence
electrically floating.
DS3625
-
Rev 21
page 3/31
RHFL4913A
Maximum ratings
3
Maximum ratings
Table 2.
Recommended maximum operating ratings
Symbol
V
I
V
O
V
ADJ
V
OCM
V
ISC
V
INHIBIT
I
O
I
O
P
D
T
STG
T
OP
E
SD
Parameter
DC input voltage, V
I
- V
GROUND
DC output voltage range
ADJ pin voltage
Over current monitor pin voltage vs. GND
Current limit pin voltage vs. GND
Inhibit pin voltage vs. GND
Output current, RHFL4913KPA
Output current, RHFL4913SCA
T
C
= 25 °C power dissipation
Storage temperature range
Operating junction temperature range
Electrostatic discharge capability
Value
12
1.23 to 9
-0.3 to (V
O
+ 0.3)
-0.3 to (V
I
+ 0.3)
-0.3 to (V
I
+ 0.3)
-0.3 to (V
I
+ 0.3)
2
3
15
-65 to +150
-55 to +150
Class 3
Unit
V
V
V
V
V
V
A
W
°C
°C
Note:
Exceeding maximum ratings may damage the device.
Table 3.
Thermal data
Symbol
R
thJC
T
SOLD
Parameter
Thermal resistance junction-case, FLAT-16 and SMD5C
Maximum soldering temperature, 10 sec.
Value
8.3
300
Unit
°C/W
°C
DS3625
-
Rev 21
page 4/31
RHFL4913A
Electrical characteristics
4
Electrical characteristics
T
J
= 25 °C, V
I
= V
O
+ 2.5 V, C
I
= C
O
= 1 µF, unless otherwise specified.
Table 4.
Electrical characteristics
Symbol
V
I
Parameter
Operating input voltage
Test conditions
I
O
= 1 A, T
J
= -55 to 125 °C
I
O
= 1 A for FLAT-16,
2 A for SMD5C,
V
O
Output voltage
V
O
= V
ADJ
I
O
= 1 A for FLAT-16,
2 A for SMD5C,
V
O
= 9 V
I
SHORT
Output current limit
(1)
Adjustable by mask/external resistor
V
I
= V
O
+2.5 V to 12 V,
I
O
= 5 mA, T
J
= +25 °C
V
I
= V
O
+2.5 V to 12 V,
∆V
O
/∆V
I
Line regulation
I
O
= 5 mA, T
J
= -55 °C
V
I
= V
O
+2.5 V to 12 V,
I
O
= 5 mA, T
J
= +125 °C
V
I
= 3 V to 12 V,
I
O
= 5 mA, T
J
= -55 °C to +125 °C
V
I
= V
O
+ 2.5 V,
I
O
= 5 to 400 mA, T
J
= +25 °C
V
I
= V
O
+ 2.5 V,
I
O
= 5 to 400 mA, T
J
= -55 °C
V
I
= V
O
+ 2.5 V,
I
O
= 5 to 400 mA, T
J
= +125 °C
V
I
= V
O
+ 2.5 V,
∆V
O
/∆I
O
Load regulation
I
O
= 5 mA to 1 A, T
J
= +25 °C
V
I
= V
O
+ 2.5 V,
I
O
= 5 mA to 1 A, T
J
= -55 °C
V
I
= V
O
+ 2.5 V,
I
O
= 5 mA to 1 A, T
J
= +125 °C
V
I
= 3 V,
I
O
= 5 mA to 1 A,
T
J
= -55 °C to +125 °C
Z
OUT
Output impedance
I
O
= 100 mA DC and 20 mA rms
100
mΩ
0.1
0.7
1
4.5
0.07
0.35
A
8.7
9.3
1.19
1.23
1.27
V
Min.
3
Typ.
Max.
12
Unit
V
0.05
0.4
%
0.1
0.4
0.1
0.5
0.04
0.3
0.02
0.5
0.02
0.5
0.08
0.5
%
0.05
0.6
0.04
0.6
DS3625
-
Rev 21
page 5/31
聊聊、笑笑、闹闹
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
