SHOULDER
SPECIFICATION
Item:
Type:
CRYSTAL
SMD0503
Optional
SHOULDER
SMD0503 CRYSTAL
Scope
This specification shall cover the characteristics of SMD 5x3.2 crystal.
Ultra small package
Wide Frequency Range
Electrical Specification
Parameter
Nominal Frequency
Frequency Tolerance (at 25°C)
Frequency Stability
Oscilation Mode
Equivalent Series resistance
Drive Level
Operating Temperature Range
Storage Temperature
Load Capacitance
Shunt Capacitance
Aging (at 25°C)
Insulation Resistance
Value
10.00 to 80.000 MHz
+ 30 PPM (Maximum)
+30 PPM (Maximum)
Fundamental
50Ω
1.0 mW (Maximum)
-20 to + 70ºC Standard (or Optional)
-40 to + 85ºC
10 pF to Series
<
7 PF
+ 3 ppM per year
>
500 MΩ at DC 100V
Mechanical Dimensions (All in mm) SMD0503
SHOULDER INDÚSTRIA ELETRÔNICA LTDA
Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema)
CEP 37640-000 Extrema / MG
Page 2 of 5
www.hdshoulder.com.br
SHOULDER
SMD0503 CRYSTAL
Mechanical Specification
Conditions
1. Vibration test
Frequency
Amplitude
Sweep
Duration
2. Drop test
Method of drop
Dropping floor
Height
Number of drops
Natural drop
Hard wood board
30cm
3 times
Frequency and wave form of tested products
must remain within specifications.
Results
10 ~ 55Hz
0.762mm
1.0 minute
2 hours
Frequency and wave form of tested products
must remain within specifications.
Environmental Specification
Conditions
1. Temperature test
1) at -55°C, 30 minutes
2) at +25°C, 10~15 minutes
Steps of cycle
Temperature cycling test
3) at +85°C, 30 minutes
4) at +25°C, 10~15 minutes
Number of cycles 3 times
2. Aging test
Temperature
+85°C ±20°C
Length of test
96 hours
3. Salt spray test
Temperature
+35°C ±2°C
Length of test
48 hours
NaCI %
5%
4. Humidity test
Temperature
+40°C ±2°C
Relative humidity 90 ~ 95%
Length of test
96 hours
Frequency and wave form of tested products
must remain within specifications.
Results
Deviation of frequency must be less
than ±3ppM.
There should be no stain on surface of
products.
a) Insulation resistance must be
500 MΩ/100 Vac minimum.
b) Resistance and wave form must remain
within specifications.
Soldering
SHOULDER INDÚSTRIA ELETRÔNICA LTDA
Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema)
CEP 37640-000 Extrema / MG
Page 3 of 5
www.hdshoulder.com.br
SHOULDER
SMD0503 CRYSTAL
Tape Specifications (All in mm)
Reeling Quantity - 1000pcs / reel
Carrier Tape Dimensions
W
16+
0.3
F
5.5+
0.05
P0
4.0+
0.1
P1
9.0+
0.1
D0
∅1.5+
0.1
D1
∅1.6
+
0.25
t1
0.3+
0.03
t2
1.7+
0.1
A
4.2+
0.1
B
6+
0.1
SMD0503 CRYSTAL Part Numbering System (Example)
SHOULDER INDÚSTRIA ELETRÔNICA LTDA
Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema)
CEP 37640-000 Extrema / MG
Page 4 of 5
www.hdshoulder.com.br
SHOULDER
SMD0503 CRYSTAL
SMD0503
11.0592
F
20
30
30
A
T
Type
Nominal Frequency
(in MHz)
Vibration
Mode
Load
Capacitance
Frequency
Tolerance
Frequency
Stability
Operating
Temperature
Range
A
-20°C to 70°C
-10°C to 60°C
0°C to 50°C
-30°C to 80°C
-40°C to 85°C
Option
(can be blank)
SMD0503
49S-SMD
49S2-SMD
SMD0804
SMD0705
SMD0603
SMD0402
Enter the
nominal frequency
(3 digits after dot)
or up to last significant
digit (different
than zero)
S = Series
F = Fund
Or enter load
capacitance:
10 to 33 for
parallel
Indicate the
tolerance value
in ± PPM
Indicate the
stability over
temperature
range value
in ± PPM
B
C
D
E
S= Standard
X= Additional
Specifications
T= Tape and Reel
SHOULDER INDÚSTRIA ELETRÔNICA LTDA
Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema)
CEP 37640-000 Extrema / MG
Page 5 of 5
www.hdshoulder.com.br