REVISIONS
LTR
A
B
C
DESCRIPTION
Changes in accordance with N.O.R. 5962-R180-94.
Drawing updated to reflect current requirements. -ro
Update boilerplate paragraphs to current MIL-PRF-38535 requirements.
Replace reference to MIL-STD-973 with reference to MIL-PRF-38535. -rrp
DATE (YR-MO-DA)
94-06-14
00-09-15
09-08-05
APPROVED
M. A. FRYE
R. MONNIN
C. SAFFLE
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
REV
SHEET
PREPARED BY
RICK C. OFFICER
C
1
C
2
C
3
C
4
C
5
C
6
C
7
C
8
C
9
C
10
C
11
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
CHARLES E. BESORE
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
APPROVED BY
MICHAEL A. FRYE
MICROCIRCUIT, LINEAR, PRECISION, LOW
DRIFT, OPERATIONAL AMPLIFIER, MONOLITHIC
SILICON
DRAWING APPROVAL DATE
92-10-29
AMSC N/A
REVISION LEVEL
C
SIZE
A
SHEET
CAGE CODE
67268
1 OF
11
5962-90842
DSCC FORM 2233
APR 97
5962-E143-08
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and
M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part
or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN.
1.2 PIN. The PIN is as shown in the following example:
5962
-
90842
01
M
G
X
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
/
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
\/
Drawing number
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are
marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
02
Generic number
LT1012
LT1012A
Circuit function
Precision, low drift, operational amplifier
Precision, low drift, operational amplifier
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as
follows:
Device class
M
Device requirements documentation
Vendor self-certification to the requirements for MIL-STD-883 compliant,
non-JAN class level B microcircuits in accordance with MIL-PRF-38535,
appendix A
Certification and qualification to MIL-PRF-38535
Q or V
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
G
P
Descriptive designator
MACY1-X8
GDIP1-T8 or CDIP2-T8
Terminals
8
8
Package style
Can
Dual-in-line
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-90842
SHEET
C
2
1.3 Absolute maximum ratings. 1/
Supply voltage (V
S
) .......................................................................
±20
V
Differential input current ................................................................
±10
mA 2/
Input voltage (V
IN
) .........................................................................
±20
V
Power dissipation (P
D
) ..................................................................
Output short circuit duration ...........................................................
Storage temperature range ............................................................
Lead temperature (soldering, 10 seconds) ....................................
Thermal resistance, junction-to-case (θ
JC
) ....................................
24 mW
Indefinite
-65°C to +150°C
+300°C
See MIL-STD-1835
Thermal resistance, junction-to-ambient (θ
JA
):
Case G ....................................................................................... +150°C/W
Case P ....................................................................................... +100°C/W
1.4 Recommended operating conditions.
Supply voltage (V
S
) .......................................................................
±15
V
Ambient operating temperature range (T
A
) ................................... -55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 -
MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at
http://assist.daps.dla.mil/quicksearch/
or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
1/
2/
Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
Differential input voltages greater than 1 V will cause excessive current to flow through the input protection diodes unless
limiting resistance is used.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-90842
SHEET
C
3
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.3 Electrical performance characteristics and post irradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and post irradiation parameter limits are as specified in table I and shall apply over the full
ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be
in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this
drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and
herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2
herein) involving devices acquired to this drawing is required for any change that affects this drawing.
3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in
microcircuit group number 49 (see MIL-PRF-38535, appendix A).
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-90842
SHEET
C
4
TABLE I. Electrical performance characteristics.
Conditions
-55°C
≤
T
A
≤
+125°C
V
S
=
±15
V, V
CM
= 0 V
unless otherwise specified
Input offset voltage
V
OS
4
2,3
4
2,3
2/
1
2,3
1
2,3
Input offset current
I
OS
1
2,3
2/
1
2,3
Input bias current
I
B
1
2,3
2/
1
2,3
Common mode rejection
ratio
CMRR
V
CM
=
±13.5
V
1
2,3
1
2,3
Power supply rejection
ratio
PSRR
V
S
=
±1.2
V to
±20
V
V
S
=
±1.5
V to
±20
V
1
2,3
All
01
02
02
01
All
All
02
01
02
01
Test
Symbol
Group A
subgroups
Device
type
Limits 1/
Unit
Min
-35
-180
-25
-60
-90
-250
-90
-180
-100
-250
-150
-350
-100
-600
-150
-800
114
108
114
110
114
108
110
Max
35
180
25
60
90
250
90
180
100
250
150
350
100
600
150
800
µV
pA
pA
dB
dB
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-90842
SHEET
C
5
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
