2.1 OPTIONS AND PART IDENTIFICATION (Left blank if standard)
ASL - Frequency -
Operating Temp. Range
-
-
-
-
-
Packaging
Overall Frequency Stability
I
D
E
F
N
L
0°C to +50°C
-10°C to +60°C
-20°C to +70°C
-30°C to +70°C
-30°C to +85°C
-40°C to +85°C
J*
R
K
H
C
±20ppm
±25ppm
±30ppm
±35ppm
±50ppm
Blank
T
Bulk
Tape and Reel
(1,000pcs/reel
*Temp. option I, D, E, and -10°C to +70°C only
Power down
Blank
B
Symmetry
Tri-state
Tri-state with PD
Output Load
S
S1
45/55%@1/2Vdd
45/55%@1/4Vdd
50
50pF
3.0 SPECIAL REQUIREMENT
This product is RoHS compliant and Pb free.
NOTE: The information contained in this Source Control Drawing is subject to Abracon’s standard Terms and Conditions of Sale. The full text can be found at http://www.abracon.com/Support/terms.pdf.
Drawing No. :
400687
Rev. J
Page 3 of 9
4.0 Marking
Frequency MHz
Frequency Stability option
Symmetry option
XX.X RS
ASL ZYW
Traceability code
Last digit of year (7 for 2007)
Month (A to L)
Month
January
February
March
April
May
June
July
August
September
October
November
December
Code
A
B
C
D
E
F
G
H
I
J
K
L
4.1 Marking Method : Laser Marking
NOTE: The information contained in this Source Control Drawing is subject to Abracon’s standard Terms and Conditions of Sale. The full text can be found at http://www.abracon.com/Support/terms.pdf.
Drawing No. :
400687
Rev. J
Page 4 of 9
5.0 Outline dimensions
PIN
1
2
3
4
FUNCTION
Tristate Enable/Disable
GND/Case
Output
Vdd
Note: Recommend using an approximately
0.01uF bypass capacitor between PIN 2 and 4.
Dimension : Inches (mm)
TOLERANCES:
UNLESS OTHERWISE SPECIFIED:
.X: ± 0.1 (0.25)
.XX: ± 0.01 (0.025)
.XXX: ± 0.005 (0.013)
NOTE: The information contained in this Source Control Drawing is subject to Abracon’s standard Terms and Conditions of Sale. The full text can be found at http://www.abracon.com/Support/terms.pdf.
Drawing No. :
400687
Rev. J
Page 5 of 9
6.0 Reliability Test
No.
1
Test Items
Temperature Cycling:
Test Conditions
The component shall remain within the electrical specification
(± 5 ppm max) after 3 cycles of high and low temperature
testing (-40°C to +85°C) for 2 hours max.
The component shall remain within the electrical specification
after exposure at extreme temperature -40°C to +85°C for 5
minutes for 3 cycles.
The component shall remain within the electrical specification after
loaded vibration at 10Hz to 55Hz, amplitude 1.5mm, within 1 minute
for 2 hours minimum on each axis (X,Y,Z).
2
Thermal Shock:
3
Vibration:
4
Drop Test:
5
Humidity:
The component shall remain within the electrical
specifications after a natural drop (3X) on a hard wooden
board at 75 cm.
The component shall remain within the electrical
specifications after being kept at a condition of ambient
temperature +85°C, 85% RH for 96 hours minimum.
Expose samples to 60PSIG Helium gas for 2 hours.
Max leak rate 2X10-8atmcc/s.
Submerge samples in 100% De-ionized water or
Perfluorocarbon at 85°C for at least 1 minute. Check for
bubbles.
Solderability of terminals shall be kept at more than 95% after
dipped in solder flux at 260°C ± 5°C for 5 seconds.
6
Fine Leak Test:
7
Gross Leak Test:
8
Solderability:
6.1 Reflow Profile
NOTE: The information contained in this Source Control Drawing is subject to Abracon’s standard Terms and Conditions of Sale. The full text can be found at http://www.abracon.com/Support/terms.pdf.
SynQor推出超小的病人全接触型400W医疗电源模块，该电源模块的封装为3×5×1.44，功率密度高达18.3W/立方英寸，转换效率达91%。 SynQor通过推出首款专门针对医疗应用而研制的AC/DC电源模块，使得公司的多元化战略持续成功地延伸至新的医疗领域。ACuQor模块系列实现了在3×5×1.44有限尺寸上提供400W的有用功率。SynQor可以提供48V，36V or 24V的...[详细]
便携式医疗设备的特殊性决定了它们应该是对用户友好的、必须工作在无菌环境下，并且空间占用小、耗能低。 同时，便携式医疗设备还需要足够的计算能力以便处理医疗数据，能够连接到无线或有线接口以便记录和发送数据。从设计人员的角度考虑，上述需求需要低功耗的单片机（MCU）和数字信号控制器（Digital Signal Controller，DSC）。 正是有了嵌入式处理器，设计人员才有可能设...[详细]
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
