Hardware
Documentation
Da t a Sh e et
HAL 556, HAL 566
Two-Wire Hall-Effect Sensors
®
Edition Sept. 18, 2014
DSH000026_006EN
HAL556, HAL566
Copyright, Warranty, and Limitation of Liability
The information and data contained in this document
are believed to be accurate and reliable. The software
and proprietary information contained therein may be
protected by copyright, patent, trademark and/or other
intellectual property rights of Micronas. All rights not
expressly granted remain reserved by Micronas.
Micronas assumes no liability for errors and gives no
warranty representation or guarantee regarding the
suitability of its products for any particular purpose due
to these specifications.
By this publication, Micronas does not assume respon-
sibility for patent infringements or other rights of third
parties which may result from its use. Commercial con-
ditions, product availability and delivery are exclusively
subject to the respective order confirmation.
Any information and data which may be provided in the
document can and do vary in different applications,
and actual performance may vary over time.
All operating parameters must be validated for each
customer application by customers’ technical experts.
Any new issue of this document invalidates previous
issues. Micronas reserves the right to review this docu-
ment and to make changes to the document’s content
at any time without obligation to notify any person or
entity of such revision or changes. For further advice
please contact us directly.
Do not use our products in life-supporting systems,
military, aviation, or aerospace applications! Unless
explicitly agreed to otherwise in writing between the
parties, Micronas’ products are not designed, intended
or authorized for use as components in systems
intended for surgical implants into the body, or other
applications intended to support or sustain life, or for
any other application in which the failure of the product
could create a situation where personal injury or death
could occur.
No part of this publication may be reproduced, photo-
copied, stored on a retrieval system or transmitted
without the express written consent of Micronas.
Micronas Trademarks
–
HAL
DATA SHEET
Third-Party Trademarks
All other brand and product names or company names
may be trademarks of their respective companies.
2
Sept. 18, 2014; DSH000026_006EN
Micronas
DATA SHEET
HAL556, HAL566
Contents
Page
4
4
4
5
5
6
7
7
12
12
12
12
12
13
13
13
14
15
18
18
20
22
22
22
22
23
23
24
Section
1.
1.1.
1.2.
2.
2.1.
3.
4.
4.1.
4.2.
4.3.
4.4.
4.4.1.
4.4.2.
4.5.
4.5.1.
4.6.
4.7.
4.8.
5.
5.1.
5.2.
6.
6.1.
6.2.
6.3.
6.4.
6.5.
7.
Title
Introduction
Features
Family Overview
Ordering Information
Device-Specific Ordering Codes
Functional Description
Specification
Outline Dimensions
Solderability and Welding
Pin Connections and Short Descriptions
Physical Dimension
Sensitive Area
Position
Absolute Maximum Ratings
Storage and Shelf Life
Recommended Operating Conditions
Characteristics
Magnetic Characteristics Overview
Type Description
HAL556
HAL566
Application Notes
Application Circuit
Extended Operating Conditions
Start-up Behavior
Ambient Temperature
EMC and ESD
Data Sheet History
Micronas
Sept. 18, 2014; DSH000026_006EN
3
HAL556, HAL566
Two-Wire Hall-Effect Sensors
Release Note: Revision bars indicate significant
changes to the previous edition.
1.2. Family Overview
DATA SHEET
The types differ according to the mode of switching
and the magnetic switching points.
1. Introduction
This sensor family consists of different two-wire Hall
switches produced in CMOS technology. All sensors
change the current consumption depending on the
external magnetic field and require only two wires
between sensor and evaluation circuit. The sensors of
this family differ in the magnetic switching behavior
and switching points.
The sensors include a temperature-compensated Hall
plate with active offset compensation, a comparator,
and a current source. The comparator compares the
actual magnetic flux through the Hall plate (Hall volt-
age) with the fixed reference values (switching points).
Accordingly, the current source is switched on (high
current consumption) or off (low current consumption).
The active offset compensation leads to constant mag-
netic characteristics in the full supply voltage and tem-
perature range. In addition, the magnetic parameters
are robust against mechanical stress effects.
The sensors are designed for industrial and automo-
tive applications and operate with supply voltages from
4 V to 24 V in the junction temperature range from
40 C
up to 140
C.
All sensors are available in the
SMD-package SOT89B-1 and in the leaded versions
TO92UA-1 and TO92UA-2.
Type
556
566
Switching
Behavior
unipolar
unipolar
inverted
Sensitivity
very high
very high
see
Page
18
20
Unipolar Switching Sensors:
The sensor turns to high current consumption with the
magnetic south pole on the branded side of the pack-
age and turns to low consumption if the magnetic field
is removed. The sensor does not respond to the mag-
netic north pole on the branded side.
Unipolar Inverted Switching Sensors:
The sensor turns to low current consumption with the
magnetic south pole on the branded side of the pack-
age and turns to high consumption if the magnetic field
is removed. The sensor does not respond to the mag-
netic north pole on the branded side.
1.1. Features
– Current output for two-wire applications
– Junction temperature range from
40 C
up to 140
C.
– Operates from 4 V to 24 V supply voltage
– Operates with static magnetic fields and dynamic
magnetic fields up to 10 kHz
– Switching offset compensation at typically 145 kHz
– Overvoltage and reverse-voltage protection
– magnetic characteristics are robust against
mechanical stress effects
– Constant magnetic switching points over a wide
supply voltage range
– The decrease of magnetic flux density caused by
rising temperature in the sensor system is compen-
sated by a built-in negative temperature coefficient
of the magnetic characteristics
– Ideal sensor for applications in extreme automotive
and industrial environments
– EMC corresponding to ISO 7637
4
Sept. 18, 2014; 000026_006ENDSH
Micronas
DATA SHEET
HAL556, HAL566
2.1. Device-Specific Ordering Codes
HAL556, HAL566 is available in the following package
and temperature variants.
Table 2–1:
Available packages
2. Ordering Information
A Micronas device is available in a variety of delivery
forms. They are distinguished by a specific ordering
code:
XXX NNNN PA-T-C-P-Q-SP
Further Code Elements
Temperature Range
Package
Product Type
Product Group
Package Code (PA)
UA
SF
Package Type
TO92UA
SOT89B-1
Table 2–2:
Available temperature ranges
Fig. 2–1:
Ordering Code Principle
For a detailed information, please refer to the brochure:
“Hall Sensors: Ordering Codes, Packaging, Handling”
.
Temperature Code (T)
E
K
Temperature Range
TJ =
40
°C to +100 °C
TJ =
40
°C to +140 °C
The relationship between ambient temperature (T
A
)
and junction temperature (T
J
) is explained in
Section 5.4. on page 29.
For available variants for Configuration (C), Packaging
(P), Quantity (Q), and Special Procedure (SP) please
contact Micronas.
Table 2–3:
Available ordering codes and
corresponding package marking
Available Ordering Codes
HAL556UA-E-[C-P-Q-SP]
HAL556UA-K-[C-P-Q-SP]
HAL566SF-E-[C-P-Q-SP]
HAL566SF-K-[C-P-Q-SP]
Package Marking
556E
556K
566E
566K
Micronas
Sept. 18, 2014; DSH000026_006EN
5
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
