82C50A
March 1997
CMOS Asynchronous
Communications Element
Description
The 82C50A Asynchronous Communication Element (ACE)
is a high performance programmable Universal Asynchro-
nous Receiver/Transmitter (UART) and Baud Rate Genera-
tor (BRG) on a single chip. Using Intersil’s advanced Scaled
SAJI IV CMOS Process, the ACE will support data rates
from DC to 625K baud (0-10MHz clock).
The ACE’s receiver circuitry converts start, data, stop, and
parity bits into a parallel data word. The transmitter circuitry
converts a parallel data word into serial form and appends
the start, parity, and stop bits. The word length is program-
mable to 5, 6, 7, or 8 data bits. Stop bit selection provides a
choice of 1,1.5, or 2 stop bits.
The Baud Rate Generator divides the clock by a divisor
programmable from 1 to 2
16
-1 to provide standard RS-232C
baud rates when using any one of three industry standard
baud rate crystals (1.8432MHz, 2.4576MHz, or 3.072MHz).
A programmable buffered clock output (BAUDOUT) provides
either a buffered oscillator or 16X (16 times the data rate)
baud rate clock for general purpose system use.
To meet the system requirements of a CPU interfacing to an
asynchronous channel, the modem control signals RTS,
CTS, DSR, DTR, RI, DCD are provided. Inputs and outputs
have been designed with full TTL/CMOS compatibility in
order to facilitate mixed TTL/NMOS/CMOS system design.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Single Chip UART/BRG
DC to 625K Baud (DC to 10MHz Clock)
Crystal or External Clock Input
On Chip Baud Rate Generator 1 to 65535 Divisor
Generates 16X Clock
Prioritized Interrupt Mode
Fully TTL/CMOS Compatible
Microprocessor Bus Oriented Interface
80C86/80C88 Compatible
Scaled SAJI IV CMOS Process
Low Power - 1mA/MHz Typical
Modem Interface
Line Break Generation and Detection
Loopback and Echo Modes
Doubled Buffered Transmitter and Receiver
Single 5V Supply
Ordering Information
PACKAGE
PDIP
PLCC
CERDIP
TEMPERATURE
RANGE (
o
C)
0 to +70
-40 to +85
0 to +70
-40 to +85
0 to +70
-40 to +85
-55 to +125
625K BAUD
CP82C50A-5
IP82C50A-5
CS82C50A-5
IS82C50A-5
CD82C50A-5
ID82C50A-5
MD82C50A-5/B
PKG.
NO.
E40.6
E40.6
N44.65
N44.65
F40.6
F40.6
F40.6
Functional Diagram
CSO
CS1
CS2
ADS
A0
A1
A2
MR
DISTR
DISTR
12
13
14
25
28
27
26
35
22
21
LINE STATUS
AND CONTROL
INTERRUPT
ENABLE,
ID, & CONTROL
MICROPROCESSOR INTERFACE
24
23
30
CSOUT
DDIS
INTRPT
UART
10
RECEIVER
DIVISOR LATCH
AND BAUD RATE
GENERATOR
TRANSMITTER
MODEM
MODEM CONTROL
9
16
17
11
32
33
34
31
36
37
MODEM STATUS
38
39
SIN
RCLK
XTAL1
XTAL2
SOUT
RTS
DTR
OUT1
OUT2
CTS
DSR
DCD
RI
15 BAUDOUT
DOSTR 19
DOSTR 18
D0
D1
D2
D3
D4
D5
D6
D7
1
2
3
4
5
6
7
8
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207
|
Copyright
©
Intersil Corporation 1999
File Number
2958.1
1
82C50A
Pinouts
82C50A (PDIP, CERDIP)
TOP VIEW
D0
D1
D2
D3
D4
D5
D6
D7
RCLK
SIN
SOUT
CS0
CS1
CS2
BAUDOUT
XTAL1
XTAL2
DOSTR
DOSTR
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
40 V
CC
39 RI
38 DCD
37 DSR
36 CTS
35 MR
34 OUT1
33 DTR
32 RTS
31 OUT2
30 INTRPT
29 NC
28 A0
27 A1
26 A2
25 ADS
24 CSOUT
23 DDIS
22 DISTR
21 DISTR
82C50A (PLCC)
TOP VIEW
DCD
DSR
CTS
V
CC
NC
D4
D3
D2
D1
D0
RI
6
5
4
3
2
1 44 43 42 41 40
39
38
37
36
35
34
33
32
31
30
29
D5
D6
D7
RCLK
SIN
NC
7
8
9
10
11
12
13
14
15
16
17
18 19 20 21 22 23 24 25 26 27 28
MR
OUT1
DTR
RTS
OUT2
NC
SOUT
CS0
CS1
CS2
BAUDOUT
INTRP
NC
A0
A1
A2
DOSTR
DOSTR
CSOUT
XTAL1
XTAL2
DISTR
DISTR
DDIS
GND
2
ADS
NC
82C50A
Pin Description
SYMBOL
DISTR,
DISTR
PIN
NUMBER
22
21
TYPE
I
I
ACTIVE
LEVEL
H
L
DESCRIPTION
DATA IN STROBE, DATA IN STROBE: DISTR, DISTR are read inputs which cause
the 82C50A to output data to the data bus (D0-D7). The data output depends upon
the register selected by the address inputs A0, A1, A2. The chip select inputs CS0,
CS1, CS2 enable the DISTR, DISTR inputs.
Only an active DISTR or DISTR, not both, is used to receive data from the 82C50A
during a read operation. If DISTR is used as the read input, DlSTR should be tied
high. If DISTR is used as the active read input, DISTR should be tied low.
DOSTR,
DOSTR
19
18
I
I
H
L
DATA OUT STROBE, DATA OUT STROBE: DOSTR, DOSTR are write inputs which
cause data from the data bus (D0-D7) to be input to the 82C50A. The data input de-
pends upon the register selected by the address inputs A0, A1, A2. The chip select
inputs CS0, CS1, CS2 enable the DOSTR, DOSTR inputs.
Only an active DOSTR or DOSTR, not both, is used to transmit data to the 82C50A
during a write operation. If DOSTR is used as the write input, DOSTR should be tied
high. If DOSTR is used as the write input, DOSTR should be tied low.
D0-D7
1-8
I/O
DATA BITS 0-7: The Data Bus provides eight, three-state input/output lines for the
transfer of data, control and status information between the 82C50A and the CPU.
For character formats of less than 8 bits, D7, D6 and D5 are “don’t cares” for data
write operations and 0 for data read operations. These lines are normally in a high
impedance state except during read operations. D0 is the Least Significant Bit (LSB)
and is the first serial data bit to be received or transmitted.
H
REGISTER SELECT: The address lines select the internal registers during CPU
bus operations. See Table 1.
CRYSTAL/CLOCK: Crystal connections for the internal Baud Rate Generator.
XTAL1 can also be used as an external clock input, in which case XTAL2 should be
left open.
SERIAL DATA OUTPUT: Serial data output from the 82C50A transmitter circuitry. A
Mark (1) is a logic one (high) and Space (0) is a logic zero (low). SOUT is held in the
Mark condition when the transmitter is disabled, MR is true, the Transmitter Register
is empty, or when in the Loop Mode. SOUT is not affected by the CTS input.
L
I
L
GROUND: Power supply ground connection (V
SS
).
CLEAR TO SEND: The logical state of the CTS pin is reflected in the CTS bit of the
(MSR) Modem Status Register (CTS is bit 4 of the MSR, written MSR (4)). A change
of state in the CTS pin since the previous reading of the MSR causes the setting of
DCTS (MSR(O)) of the Modem Status Register. When CTS pin is ACTIVE (low), the
modem is indicating that data on SOUT can be transmitted on the communications
link. If CTS pin goes INACTIVE (high), the 82C50A should not be allowed to transmit
data out of SOUT. CTS pin does not affect Loop Mode operation.
DATA SET READY: The logical state of the DSR pin is reflected in MSR(5) of the
Modem Status Register. DDSR (MSR(1)) indicates whether the DSR pin has
changed state since the previous reading of the MSR. When the DSR pin is ACTIVE
(low), the modem is indicating that it is ready to exchange data with the 82C50A,
while the DSR Pin INACTIVE (high) indicates that the modem is not ready for data
exchange. The ACTIVE condition indicates only the condition of the local Data Com-
munications Equipment (DCE), and does not imply that a data circuit as been estab-
lished with remote equipment.
DATA TERMINAL READY: The DTR pin can be set (low) by writing a logic 1 to
MCR(0), Modem Control Register bit 0. This signal is cleared (high) by writing a logic
0 to the DTR bit (MCR(0)) or whenever a MR ACTIVE (high) is applied to the
82C50A. When ACTIVE (low), DTR pin indicates to the DCE that the 82C50A is
ready to receive data. In some instances, DTR pin is used as a power on indicator.
The INACTIVE (high) state causes the DCE to disconnect the modem from the tele-
communications circuit.
A0, A1,
A2
XTAL1,
XTAL2
28, 27,
26
16
17
I
I
I
O
SOUT
11
O
GND
CTS
20
36
DSR
37
I
L
DTR
33
O
L
3
82C50A
Pin Description
SYMBOL
RTS
PIN
NUMBER
32
(Continued)
ACTIVE
LEVEL
L
TYPE
O
DESCRIPTION
REQUEST TO SEND: The RTS signal is an output used to enable the modem. The
RTS pin is set low by writing a logic 1 to MCR (1) bit 1 of the Modem Control Regis-
ter. The RTS pin is reset high by Master Reset. When ACTIVE, the RTS pin indicates
to the DCE that the 82C50A has data ready to transmit. In half duplex operations,
RTS is used to control the direction of the line.
BAUDOUT: This output is a 16X clock out used for the transmitter section (16X =
16 times the data rate). The BAUDOUT clock rate is equal to the reference oscillator
frequency divided by the specified divisor in the Baud Rate Generator Divisor Latch-
es DLL and DLM. BAUDOUT may be used by the Receiver section by tying this out-
put to RCLK.
BAUDOUT
15
O
OUT1
34
O
L
OUTPUT 1: This is a general purpose output that can be programmed ACTIVE
(low) by settingVCR(2) (OUT1) of the Modem Control Register to a high level. The
OUT1 pin is set high by Master Reset. The OUT1 pin is INACTIVE (high) during loop
mode operation.
OUTPUT 2: This is a general purpose output that can be programmed ACTIVE
(low) by setting MCR(3) (OUT1) of the Modem Control Register to a high level. The
OUT2 pin is set high by Master Reset. The OUT2 signal is INACTIVE (high) during
loop mode operation.
RING INDICATOR: When low, RI indicates that a telephone ringing signal has been
received by the modem or data set. The RI signal is a modem control input whose
condition is tested by reading MSR(6) (RI). The Modem Status Register output TERI
(MSR(2)) indicates whether the RI input has changed from a Low to High since the
previous reading of the MSR. If the interrupt is enabled (IER (3) = 1) and RI changes
from a Low to High, an interrupt is generated. The ACTIVE (low) state of RI indicates
that the DCE is receiving a ringing signal. RI will appear ACTIVE for approximately
the same length of time as the ACTIVE segment of the ringing cycle. The INACTIVE
state of RI will occur during the INACTIVE segments not detected by the DCE. This
circuit is not disabled by the INACTIVE condition of DTR.
DATA CARRIER DETECT: When ACTIVE (low), DCD indicates that the data carrier
has been detected by the modem or data set. DCD is a modem input whose condi-
tion can be tested by the CPU by reading MSR(7) (DCD) of the Modem Status Reg-
ister. MSR(3) (DDCD) of the Modem Status Register indicates whether the DCD
input has changed since the previous reading of the MSR. DOD has no effect on the
receiver. If the DCD changes state with the modem status interrupt enabled, an in-
terrupt is generated.
When DCD is ACTIVE (low), the received line signal from the remote terminal is
within the limits specified by the DCE manufacturer. The INACTIVE (high) signal in-
dicates that the signal is not within the specified limits, or is not present.
OUT2
31
O
L
RI
39
1
L
DCD
38
I
L
MR
35
1
H
MASTER RESET: The MR input forces the 82C50A into an idle mode in which all
serial data activities are suspended. The Modem Control Register (MCR) along with
its associated outputs are cleared. The Line Status Register (LSR) is cleared except
for the THRE and TEMT bits, which are set. The 82C50A remains in an idle state
until programmed to resume serial data activities. The MR input is a Schmitt trigger
input. See the DC Electrical Characteristics for Schmitt trigger logic input voltage
levels. See Table 7 for a summary of Master Reset’s effect on 82C50A operation.
INTERRUPT REQUEST: The lNTRPT output goes ACTIVE (high) when one of the
following interrupts has an ACTIVE (high) condition and is enabled by the Interrupt
Enable Register: Receiver Error flag, Received Data Available, Transmitter Holding
Register Empty, and Modem Status. The lNTRPT is reset low upon appropriate ser-
vice or a MR operation. See Figure 1. Interrupt Control Structure.
SERIAL DATA INPUT: The SIN input is the serial data input from the communication
line or modem to the 82C50A receiver circuits. A mark (1) is high, and a space (0)
is low. Data inputs on SIN are disabled when operating in the loop mode.
lNTRPT
30
O
H
SIN
10
I
H
4
82C50A
Pin Description
SYMBOL
V
CC
CS0, CS1,
CS2
PIN
NUMBER
40
(Continued)
ACTIVE
LEVEL
H
TYPE
DESCRIPTION
V
CC
: +5V positive power supply pin. A 0.1µA decoupling capacitor from V
CC
(pin
40) to GND (pin 20) is recommended.
CHIP SELECT: The Chip Select inputs act as enable signals for the write (DOSTR,
DOSTR) and read (DlSTR, DlSTR) input signals. The Chip Select inputs are latched
by the ADS input.
Do Not Connect
12,13,
14
I
I
H, H,
L
NC
CSOUT
29
24
O
H
CHIP SELECT OUT: When ACTIVE (high), this pin indicates that the chip has been
selected by active CS0, CS1, and CS2 inputs. No data transfer can be initiated until
CSOUT is a logic 1, ACTIVE (high).
DRIVER DISABLE: This output is INACTIVE (low) when the CPU is reading data
from the 82C50A. An ACTIVE (high) Dells output can be used to disable an external
transceiver when the CPU is reading data.
ADDRESS STROBE: When ACTIVE (low), ADS latches the Register Select (A0,
A1, A2) and Chip Select (CS0, CS1, CS2) inputs. An active ADS is required when
the Register Select pins are not stable for the duration of the read or write operation,
multiplexed mode. If not required, the ADS input should be tied low, non-multiplexed
mode.
This input is the 16X Baud Rate Clock for the receiver section of the 82C50A. This
input may be provided from the BAUDOUT output or an external clock.
DDIS
23
O
H
ADS
25
I
L
RCLK
9
I
Block Diagram
(1 - 8)
D7 - D0
+5V
GND
A0
A1
A2
CS0
CS1
CS2
ADS
MR
DISTR
DISTR
DOSTR
DOSTR
DDIS
CSOUT
XTAL1
XTAL2
(40)
(20)
(28)
(27)
(26)
(12)
(13)
(14)
(25)
(35)
(22)
(21)
(19)
(18)
(23)
(24)
(16)
(17)
DATA BUS
BUFFER
POWER
SUPPLY
RECEIVER BUFFER
REGISTER
LINE CONTROL
REGISTER
DIVISOR
LATCH (LS)
DIVISOR
LATCH (MS)
SELECT
&
CONTROL
LOGIC
LINE STATUS
REGISTER
TRANSMITTER
HOLDING REGISTER
RECEIVER SHIFT
RECEIVER
RECEIVER TIMING
& CONTROL
(10)
(9)
SIN
RCLK
BAUD RATE
GENERATOR
(15)
BAUDOUT
TRANSMITTER
TIMING & CONTROL
TRANSMITTER
SHIFT REGISTER
(11)
SOUT
MODEM CONTROL
REGISTER
MODEM
CONTROL
LOGIC
MODEM STATUS
REGISTER
(32)
(33)
(34)
(31)
(36)
(37)
(38)
(39)
RTS
DTR
OUT1
OUT2
CTS
DSR
DCD
RI
SCRATCH
REGISTER
INTERRUPT ENABLE
REGISTER
INTERRUPT IO
REGISTER
INTERRUPT
CONTROL
LOGIC
(30)
INTRPT
5
电源技术
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
