INTEGRATED CIRCUITS
DATA SHEET
For a complete data sheet, please also download:
•
The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications
•
The IC06 74HC/HCT/HCU/HCMOS Logic Package Information
•
The IC06 74HC/HCT/HCU/HCMOS Logic Package Outlines
74HC/HCT85
4-bit magnitude comparator
Product specification
File under Integrated Circuits, IC06
December 1990
Philips Semiconductors
Product specification
4-bit magnitude comparator
FEATURES
•
Serial or parallel expansion without extra gating
•
Magnitude comparison of any binary words
•
Output capability: standard
•
I
CC
category: MSI
GENERAL DESCRIPTION
The 74HC/HCT85 are high-speed Si-gate CMOS devices
and are pin compatible with low power Schottky TTL
(LSTTL). They are specified in compliance with JEDEC
standard no. 7A.
The 74HC/HCT85 are 4-bit magnitude comparators that
can be expanded to almost any length. They perform
comparison of two 4-bit binary, BCD or other monotonic
codes and present the three possible magnitude results at
the outputs (Q
A>B
, Q
A=B
and Q
A<B
). The 4-bit inputs are
QUICK REFERENCE DATA
GND = 0 V; T
amb
= 25
°C;
t
r
= t
f
= 6 ns
74HC/HCT85
weighted (A
0
to A
3
and B
0
to B
3
), where A
3
and B
3
are the
most significant bits.
The operation of the “85” is described in the function table,
showing all possible logic conditions. The upper part of the
table describes the normal operation under all conditions
that will occur in a single device or in a series expansion
scheme. In the upper part of the table the three outputs are
mutually exclusive. In the lower part of the table, the
outputs reflect the feed forward conditions that exist in the
parallel expansion scheme.
For proper compare operation the expander inputs (I
A>B
,
I
A=B
and I
A<B
) to the least significant position must be
connected as follows: I
A<B
= I
A>B
= = LOW and
I
A=B
= HIGH.
For words greater than 4-bits, units can be cascaded by
connecting outputs Q
A<B
, Q
A>Β
and Q
A=B
to the
corresponding inputs of the significant comparator.
TYPICAL
SYMBOL
t
PHL/
t
PLH
PARAMETER
propagation delay
A
n
, B
n
to Q
A>B
, Q
A<B
A
n
, B
n
to Q
A=B
I
A<B,
, I
A=B
, I
A>B
to Q
A<B
, Q
A>B
I
A=B
to Q
A=B
C
I
C
PD
Notes
1. C
PD
is used to determine the dynamic power dissipation (P
D
in
µW):
P
D
= C
PD
×
V
CC2
×
f
i
+ ∑
(C
L
×
V
CC2
×
f
o
) where:
f
i
= input frequency in MHz
f
o
= output frequency in MHz
∑
(C
L
×
V
CC2
×
f
o
) = sum of outputs
C
L
= output load capacitance in pF
V
CC
= supply voltage in V
2. For HC the condition is V
I
= GND to V
CC
For HCT the condition is V
I
= GND to V
CC
−
1.5 V
ORDERING INFORMATION
See
“74HC/HCT/HCU/HCMOS Logic Package Information”.
input capacitance
power dissipation capacitance per package
notes 1 and 2
CONDITIONS
HC
C
L
= 15 pF; V
CC
= 5 V
20
18
15
11
3.5
18
22
20
15
15
3.5
20
ns
ns
ns
ns
pF
pF
HCT
UNIT
December 1990
2
ADI 工业技术
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
