REVISIONS
LTR
A
B
DESCRIPTION
Changes in accordance with NOR 5962-R071-97. - jak
Incorporate NOR and update boilerplate to latest MIL-PRF-38535
requirements. - CFS
Add device types 02 and 03. Add test circuit to figure 4. Update boilerplate.
Editorial changes throughout. – LTG
Add appendix A to document. - LTG
Correct radiation features for device type 02 and 03 in section 1.5 and add
footnote 8/. Correct footnotes 3/ and 7/ in Table IA. Correct SEP test limits in
table IB. Correct paragraph 4.4.4.1. Update boilerplate paragraphs to current
MIL-PRF-38535 requirements.- MAA
To update test condition of V
OL
and V
OH
in table IA. To change RHA level “H”
to “G” for device type 01. Update radiation features in section 1.5 and table IB.
Update boilerplate paragraphs to current MIL-PRF-38535 requirements.- MAA
DATE (YR-MO-DA)
96-11-25
01-06-11
APPROVED
Monica L. Poelking
Thomas M. Hess
C
04-10-27
Thomas M. Hess
D
07-02-20
Thomas M. Hess
E
09-10-05
Thomas M. Hess
F
11-03-11
David J. Corbett
G
Add footnote 5 to figure 4. Add equivalent test circuit to figure 4. - jak
12-07-09
Thomas M. Hess
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
G
15
G
16
G
17
G
18
REV
SHEET
PREPARED BY
Larry T. Gauder
G
19
G
20
G
21
G
1
G
22
G
2
G
3
G
4
G
5
G
6
G
7
G
8
G
9
G
10
G
11
G
12
G
13
G
14
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
Thanh V. Nguyen
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil
APPROVED BY
Monica L. Poelking
DRAWING APPROVAL DATE
96-05-30
REVISION LEVEL
MICROCIRCUIT, DIGITAL, ADVANCED CMOS,
RADIATION HARDENED, QUAD 2-INPUT NOR
GATE, MONOLITHIC SILICON
SIZE
CAGE CODE
AMSC N/A
G
A
67268
SHEET
1
5962-96514
OF
22
5962-E393-12
DSCC FORM 2233
APR 97
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M)
and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or
Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN.
1.2 PIN. The PIN is as shown in the following examples.
5962
G
96514
01
V
X
C
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
/
\/
Drawing number
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are
marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
02
03
Generic number
54ACS02
54ACS02E
54ACS02E
Circuit function
Radiation hardened, quad 2-input NOR gate
Enhanced, radiation hardened, quad 2-input NOR gate
Enhanced, radiation hardened, quad 2-input NOR gate
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows:
Device class
M
Device requirements documentation
Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN
class level B microcircuits in accordance with MIL-PRF-38535, appendix A
Certification and qualification to MIL-PRF-38535
Q or V
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
C
X
Descriptive designator
GDIP1-T14 or CDIP2-T14
CDFP3-F14
Terminals
14
14
Package style
Dual-in-line
Flat pack
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
G
5962-96514
SHEET
2
1.3 Absolute maximum ratings. 1/ 2/ 3/
Supply voltage range (V
DD
) .................................................................................. -0.3 V dc to +7.0 V dc
DC input voltage range, any pin (V
IN
)................................................................... -0.3 V dc to V
DD
+ 0.3 V dc
DC output voltage range, any pin (V
OUT
) .............................................................. -0.3 V dc to V
DD
+ 0.3 V dc
DC input current, any one input (I
IN
).....................................................................
±10
mA
Latch-up immunity current (I
LU
) ............................................................................
±150
mA
Storage temperature range (T
STG
) ....................................................................... -65°C to +150°C
Lead temperature (soldering, 5 seconds) ............................................................ +300°C
Thermal resistance, junction-to-case (θ
JC
):
Case outlines C and X (device type 01) ............................................................. See MIL-STD-1835
Case outline X (device types 02 and 03) ........................................................... 15°C/W
Junction temperature (T
J
) .................................................................................... +175°C
Maximum package power dissipation (P
D
):
Device type 01 ................................................................................................... 1.0 W
Device type 02 and 03 ....................................................................................... 3.2 W 4/
1.4 Recommended operating conditions. 2/ 3/
Supply voltage range (V
DD
):
Device type 01 ................................................................................................... +4.5 V dc to +5.5 V dc
Device types 02 and 03 ..................................................................................... +3.0 V dc to +5.5 V dc
Input voltage range (V
IN
) ...................................................................................... +0.0 V dc to V
DD
Output voltage range (V
OUT
)................................................................................. +0.0 V dc to V
DD
Case operating temperature range (T
C
) ............................................................... -55°C to +125°C
Maximum input rise and fall time at V
DD
= 4.5 V (t
r
, t
f
) ......................................... 1 ns/V 5/
1.5 Radiation features. 6/
Maximum total dose available:
Device type 01 (dose rate = 50 – 300 rads (Si)/s) ............................................ 5 x 10
5
rads (Si) 7/
Device type 02 (effective dose rate = 1rad (Si)/s) ............................................ 1 x 10
6
rad (Si) 8/
Device type 03 (dose rate = 50 – 300 rads (Si)/s) ............................................ 5 x 10
5
rads (Si) 7/
Single event phenomenon (SEP):
Device type 01:
No SEU occurs at effective LET (see 4.4.4.4) .................................................≤ 80 MeV/(mg/cm
2
) 9/
No SEL occurs at effective LET (see 4.4.4.4)..................................................≤ 120 MeV/(mg/cm
2
) 9/
Device types 02 and 03:
No SEU occurs at effective LET (see 4.4.4.4) .................................................≤108 MeV/(mg/cm
2
) 9/
No SEL occurs at effective LET (see 4.4.4.4).................................................. ≤ 120 MeV/(mg/cm
2
) 9/
Dose rate upset (20 ns pulse) (device types 01, 02 and 03) ............................... ≥ 1 x 10
9
rad (Si)/s 9/ 10/
Dose rate induced latch-up .................................................................................
None 9/
Dose rate survivability (device types 01, 02 and 03) ........................................... ≥ 1 x 10
12
rad(Si)/s 9/
1/
Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum
levels may degrade performance and affect reliability.
2/ Unless otherwise specified, all voltages are referenced to V
SS
.
3/ The limits for the parameters specified herein shall apply over the full specified V
DD
range and case temperature range
of -55°C to +125°C unless otherwise specified.
4/ Per MIL-STD-883 method 1012.1 section 3.4.1, P
D
(Package) = (T
J
(max) - T
C
(max)) .
θ
JC
5/ Derate system propagation delays by difference in rise time to switch point for t
r
or t
f
> 1 ns/V.
6/ Radiation testing is performed on the standard evaluation circuit.
7/ Device types 01 and 03 are tested in accordance with MIL-STD-883, method 1019, condition A.
8/ Device type 02 is irradiated at dose rate = 50 - 300 rads (Si)/s in accordance with MIL-STD-883, method 1019, condition A, and is
guaranteed to a maximum total dose specified. The effective dose rate after extended room temperature anneal = 1 rad (Si)/s per
MIL-STD-883, method 1019, condition A, section 3.11.2. The total dose specification for this device only applies to the specified
effective dose rate, or lower, environment.
9/ Limits are guaranteed by design or process, but not production tested unless specified by the customer through the purchase order
or contract.
10/ This limit is applicable for device types 01, 02, 03 with V
DD
≥ 4.5 V. Device types 02 and 03 do not meet this limit at V
DD
< 4.5 V.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
G
5962-96514
SHEET
3
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those
cited in the solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 -
MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at
https://assist.dla.mil/quicksearch
or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein.
Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.
ASTM INTERNATIONAL (ASTM)
ASTM F1192 - Standard Guide for the Measurement of Single Event Phenomena (SEP) Induced by Heavy Ion
Irradiation of semiconductor Devices.
(Copies of these documents are available online at
http://www.astm.org
/
or from ASTM International, 100 Barr Harbor Drive,
P.O. Box C700, West Conshohocken, PA, 19428-2959).
2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific
exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.1.1 Microcircuit die. For the requirements of microcircuit die, see appendix A to this document.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Truth table. The truth table shall be as specified on figure 2.
3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
G
5962-96514
SHEET
4
3.2.6 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document
revision level control and shall be made available to the preparing and acquiring activity upon request.
3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical
performance characteristics and postirradiation parameter limits are as specified in table IA and shall apply over the full case
operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical
tests for each subgroup are defined in table IA.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in
accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of
supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-
PRF-38535 and herein, or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or
for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of
product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing.
3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime's agent,
and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore
documentation shall be made available onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit
group number 36 (see MIL-PRF-38535, appendix A).
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
G
5962-96514
SHEET
5
stm32/stm8
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
