REVISIONS
LTR
A
DESCRIPTION
Change footnotes in conditions for standby current drain tests. Footnote 1,
table I, change input voltage limits. Add case outline U.
Changes in accordance with N.O.R. 5962-R085-94.
Drawing updated to reflect current requirements. - ro
Add a footnote to the case outline U, TO-257 package as specified under
1.2.2. and figure 1. - ro
Drawing updated to reflect current requirements. -rrp
Update drawing to current MIL-PRF-38535 requirements. -rrp
DATE (YR-MO-DA)
92-01-13
APPROVED
M. A. FRYE
B
C
D
94-03-07
01-04-19
05-01-26
M. A. FRYE
R. MONNIN
R. MONNIN
E
F
11-04-13
17-10-12
C. SAFFLE
C. SAFFLE
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
REV
SHEET
PREPARED BY
JOSEPH A. KERBY
F
1
F
2
F
3
F
4
F
5
F
6
F
7
F
8
F
9
F
10
F
11
F
12
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
CHARLES E. BESORE
APPROVED BY
MICHAEL A. FRYE
DRAWING APPROVAL DATE
89-08-18
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil
MICROCIRCUIT, LINEAR, 8-VOLT POSITIVE
REGULATOR FIXED, MONOLITHIC SILICON
AMSC N/A
REVISION LEVEL
F
SIZE
A
CAGE CODE
67268
SHEET
1 OF 12
5962-89628
DSCC FORM 2233
APR 97
5962-E603-17
DISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited.
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-89628
01
U
A
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
Generic number
7808A
Circuit function
Positive regulator, fixed 8-volt
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
U 1/
X
Y
Z
Descriptive designator
See figure 1
See figure 1
See figure 1
MBFM4-P2
Terminals
3
3
2
2
Package style
TO-257 Single row flange mount with
isolated tab, glass sealed
TO-39 Can
TO-3 Flange mount
TO-66 Flange mount
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
Input voltage:
Operating or input shorted to ground ...................................................
Transient ..............................................................................................
Storage temperature range .....................................................................
Lead temperature (soldering, 10 seconds) ..............................................
Power dissipation (P
D
):
T
C
= +25°C:
Cases U and Z .................................................................................
Case X .............................................................................................
Case Y .............................................................................................
T
A
= +25°C:
Cases U and Z .................................................................................
Case X .............................................................................................
Case Y .............................................................................................
35 V dc
50 V dc 2/
-65°C to +150°C
+300°C
15 W
2W
20 W
3.0 W
1.0 W
4.3 W
_____
1/ For outline letter U, CAGE 34333 manufacturers the TO-257 package with ceramic seal.
2/
The 50-volt input rating refers to the ability of the regulator to withstand high line or transient conditions without damage.
Since the regulator’s maximum current capability is reduced, the output may fall out of regulation at high input voltages
under nominal loading.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-89628
SHEET
F
2
1.3 Absolute maximum ratings – continued.
Junction temperature (T
J
) ........................................................................ +150°C 3/
Thermal resistance, junction-to-case (θ
JC
):
Case U .................................................................................................
Case X..................................................................................................
Case Y..................................................................................................
Case Z ..................................................................................................
Thermal resistance, junction-to-ambient (θ
JA
):
Cases U and Z .....................................................................................
Case X .................................................................................................
Case Y..................................................................................................
1.4 Recommended operating conditions.
Input voltage range (V
IN
) ......................................................................... +11.0 V dc to +25 V dc
Ambient operating temperature range (T
A
) .............................................. -55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 -
MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
4.2°C/W
15°C/W
3°C/W
6°C/W
50°C/W
120°C/W
35°C/W
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at
http://quicksearch.dla.mil/
or from the Standardization Document Order
Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
______
3/ The device is protected by thermal shutdown circuit which is designed to turn off the output transistor whenever the
device junction temperature is in excess of +150°C.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-89628
SHEET
F
3
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used. This drawing has been modified to allow the
manufacturer to use the alternate die/fabrication requirements of paragraph A.3.2.2 of MIL-PRF-38535 or other alternative
approved by the qualifying activity.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outlines. The case outline shall be in accordance with 1.2.2 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. In addition, the manufacturer's PIN may also be
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used. For product built in accordance with A.3.2.2 of
MIL-PRF-38535, or as modified in the manufacturer’s QM plan, the “QD” certification mark shall be used in place of the "Q" or
"QML" certification mark.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and
Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the
requirements of MIL-PRF-38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that
affects this drawing.
3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime's agent, and the acquiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-89628
SHEET
F
4
TABLE I. Electrical performance characteristics.
Conditions 1/
-55°C
≤
T
A
≤
+125°C
unless otherwise specified
Test
Symbol
Group A
subgroups
1
1,2,3
1
2,3
Device
type
01
Limits
Min
7.88
7.76
Max
8.12
8.24
40
60
20
30
Unit
Output voltage
V
OUT
T
A
= +25°C
V
IN
= 11.5 to 23 V 2/
V
Line regulation 3/ 4/
V
RLINE
V
IN
= 10.5 to 25 V
01
mV
V
IN
= 11 to 17 V
1
2,3
Load regulation 3/
V
RLOAD
I
O
= 5.0 mA to 1.0 A 5/
1
2,3
01
70
100
35
50
35
50
mV
I
O
= 250 mA to 750 mA 5/
1
2,3
I
O
= 5.0 mA to 500 mA 6/
1
2,3
Standby current drain
I
SCD
1
2,3
01
6.0
6.5
mA
Standby current drain
change with line
Standby current drain
change with load
∆I
SCD
(line)
∆I
SCD
(load)
V
IN
= 11.5 V to 25 V
I
O
= 5.0 mA to 1.0 A 5/
I
O
= 5.0 mA to 500 mA 6/
∆V
OUT
= 100 mV, 5/
I
O
= 1.0 A
∆V
OUT
= 100 mV, 6/
I
O
= 500 mA
1,2,3
1,2,3
01
01
1.0
0.5
0.5
mA
mA
Dropout voltage
V
DO
1,2,3
01
2.5
V
2.5
Peak output current
I
O(pk)
T
A
= +25°C 5/
T
A
= +25°C 6/
1
01
1.5
0.5
3.3
1.7
A
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-89628
SHEET
F
5
单片机
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
