Approval sheet
RFCPL Series – 1608(0603)- RoHS Compliance
MULTILAYER CERAMIC COUPLER
Halogens Free Product
LTE Band RF Application
P/N: RFCPL1608070P08Q1C
*Contents in this sheet are subject to change without prior notice.
Page 1 of 7
ASC_RFCPL1608070P08Q1C_V02
Aug. 2016
Approval sheet
FEATURES
1.
2.
3.
4.
Miniature footprint: 1.6X 0.8 X 0.7 mm
Low Profile Thickness
Low Insertion loss
LTCC process
3
APPLICATIONS
1.
2.
3.
For TDD_LTE/FDD_LTE applications
For DCS/PCS applications
For Bluetooth, Wireless LAN 802.11b/g/ n, HomeRF
CONSTRUCTION
Top view
P3
P2
P1
PIN
1
2
3
Connection
Input
GND
Output
PIN
4
5
6
Connection
Termination
GND
Coupling
P4
DIMENSIONS
P5
P6
Figure
Symbol
L
W
T
A
B
C
D
Dimension (mm)
1.60 ± 0.15
0.80 ± 0.15
0.70 max.
0.175 ± 0.15
0.25 ± 0.15
0.25 ± 0.15
0.50 ± 0.15
0.20 ± 0.15
Top view
Bottom view
Side view
E
Page 2 of 7
ASC_RFCPL1608070P08Q1C_V02
Aug. 2016
Approval sheet
ELECTRICAL CHARACTERISTICS
RFCPL1608070P08Q1C
Frequency range
Insertion Loss
698 ~ 2690 MHz
0.20 dB max. at 698 ~ 960 MHz
0.22 dB max. at 1427.9 ~ 2170 MHz
0.25 dB max. at 2300 ~ 2690 MHz
23.0 ~ 27.0 dB @ 698 ~ 915 MHz
Coupling in BW
Directivity in BW
VSWR
Impedance
Power Capacity
Operation Temperature Range
Moisture sensitivity levels
Typical Electrical Chart
21.5 ~ 26.5 dB @ 1427.9 ~ 2025 MHz
22.5 ~ 27.5 dB @ 2300 ~ 2620 MHz
20.0 min. dB @ 698 ~ 2690 MHz
1.5 max.
50
Ω
3W
-40C ~ +85C
MSL is LEVEL 1 (Refer to : IPC/JEDEC J-STD-020)
Specification
SOLDER LAND PATTERN
SOLDER LAND PATTERN
Unit : mm
Line width to be designed to match 50 Ω characteristic impedance, depending on PCB material and thickness.
Page 3 of 7
ASC_RFCPL1608070P08Q1C_V02
Aug. 2016
Approval sheet
RELIABILITY TEST
Test item
Solderability
JIS C 0050-4.6
JESD22-B102D
Leaching
(Resistance to
dissolution of
metallization)
IEC 60068-2-58
Resistance to soldering
heat
JIS C 0050-5.4
1 minute.
*Solder temperature：2705C
*Immersion time：101 sec
Solder：Sn3Ag0.5Cu for lead-free
Loss of metallization on the edges of each
Measurement to be made after keeping at
room temperature for 242 hrs
Drop Test
JIS C 0044
Customer’s specification.
*Height：75 cm
*Test Surface：Rigid surface of concrete or
steel.
*Times：6 surfaces for each units；2 times
for each side.
Vibration
JIS C 0040
*Frequency：10Hz~55Hz~10Hz(1min)
*Total amplitude：1.5mm
*Test times：6hrs.(Two hrs each in three
mutually perpendicular directions)
Adhesive Strength
of Termination
JIS C 0051- 7.4.3
Bending test
JIS C 0051- 7.4.1
*Pressurizing force：
5N(≦0603)；10N(>0603)
*Test time：10±1 sec
The middle part of substrate shall be
No mechanical damage.
No mechanical damage.
Electrical specification shall satisfy the
descriptions in electrical characteristics under
the operational temperature range within -40
~ 85°C.
No mechanical damage.
Electrical specification shall satisfy the
descriptions in electrical characteristics under
the operational temperature range within -40
~ 85°C.
No remarkable damage or removal of the
termination.
electrode shall not exceed 25%.
*Preheating temperature：120~150℃,
No mechanical damage.
Electrical specification shall satisfy the
descriptions in electrical characteristics under
the operational temperature range within -40
~ 85°C.
Test condition / Test method
*Solder bath temperature：235
5C
*Immersion time：2
0.5 sec
Solder：Sn3Ag0.5Cu for lead-free
*Solder bath temperature：260
5C
*Leaching immersion time：30
0.5 sec
Solder : SN63A
Loss of metallization on the edges of each
electrode shall not exceed 25%.
Specification
At least 95% of a surface of each terminal
electrode must be covered by fresh solder.
pressurized by means of the pressurizing rod Electrical specification shall satisfy the
at a rate of about 1 mm/s per second until the descriptions in electrical characteristics under
deflection becomes 1mm/s and then pressure the operational temperature range within -40
shall be maintained for 51 sec.
~ 85°C.
Measurement to be made after keeping at
room temperature for 242 hours
Page 4 of 7
ASC_RFCPL1608070P08Q1C_V02
Aug. 2016
Approval sheet
Temperature cycle
JIS C 0025
1.
2.
3.
4.
303 minutes at -40C3C,
10~15 minutes at room temperature,
303 minutes at +85C3C,
10~15 minutes at room temperature,
No mechanical damage.
Electrical specification shall satisfy the
descriptions in electrical characteristics
under the operational temperature range
within -40 ~ 85°C.
Total 100 continuous cycles
Measurement to be made after keeping at
room temperature for 242 hrs
High temperature
JIS C 0021
*Temperature：85C2C
*Test duration：1000+24/-0 hours
Measurement to be made after keeping at
room temperature for 242 hrs
Humidity
(steady conditions)
JIS C 0022
*Time：1000+24/-0 hrs.
Measurement to be made after keeping at
room temperature for 242 hrs
※
500hrs measuring the first data then
1000hrs data
Low temperature
JIS C 0020
*Temperature：-40C2C
*Test duration：1000+24/-0 hours
Measurement to be made after keeping at
room temperature for 242 hrs
*Humidity：90% to 95% R.H.
*Temperature：402C
No mechanical damage.
Electrical specification shall satisfy the
descriptions in electrical characteristics under
the operational temperature range within -40
~ 85°C.
No mechanical damage.
Electrical specification shall satisfy the
descriptions in electrical characteristics under
the operational temperature range within -40
~ 85°C.
No mechanical damage.
Electrical specification shall satisfy the
descriptions in electrical characteristics under
the operational temperature range within -40
~ 85°C.
Page 5 of 7
ASC_RFCPL1608070P08Q1C_V02
Aug. 2016
聊聊、笑笑、闹闹
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
