12 Vin single output
DC-DC CONVERTERS
POLA Non-isolated
NEW Product
1
•
6 A output current
•
12 V input voltage
•
Wide-output voltage adjust
•
1.2 Vdc to 5.5 Vdc for suffix ‘W’ and
0.8 Vdc to 1.8 Vdc for suffix ‘L’
•
Auto-track™ sequencing*
•
Pre-bias start-up
•
Efficiencies up to 93%
•
Output ON/OFF inhibit
•
Output voltage sense
•
Point-of-Load-Alliance (POLA) compatible
•
Available RoHS compliant
The PTH12050 is a next generation series of non-isolated dc-dc converters offering
some of the most advanced POL features available in the industry. The primary new
feature provides for sequencing between multiple modules, a function, which is
becoming a necessity for powering advanced silicon including DSP’s, FPGA’s and
ASIC’s requiring controlled power-up and power-down Other industry leading features
include efficiencies up to 93%. The PTH12050 has an input voltage of
10.8 Vdc to
13.2 Vdc
and offers a wide output voltage range adjustable with external trim resistor,
allowing for maximum design flexibility and a pathway for future upgrades.
All specifications are typical at nominal input, full load at 25 °C unless otherwise stated
C
in
= 100 µF, C
out
= 0 µF
OUTPUT SPECIFICATIONS
Voltage adjustability
(See Note 4)
Setpoint accuracy
Line regulation
Load regulation
Total regulation
Minimum load
Ripple and noise
20 MHz bandwidth
Suffix ‘W’
Suffix ‘L’
V
o
V
o
V
o
V
o
≤ 2.5 V
> 2.5 V
≤ 1.0 V
> 1.0 V
Suffix ‘W’
Suffix ‘L’
1.2-5.5 Vdc
0.8-1.8 Vdc
±2.0% Vo
±5 mV typ.
±5 mV typ.
±3.0% Vo
0A
25 mV pk-pk
1% V
o
20 mV pk-pk
30 mV pk-pk
±0.5% Vo
EMC CHARACTERISTICS
Electrostatic discharge
Conducted immunity
Radiated immunity
EN61000-4-2, IEC801-2
EN61000-4-6
EN61000-4-3
PTH12050
2 YEAR WARRANTY
SPECIFICATIONS
GENERAL SPECIFICATIONS
Efficiency
Insulation voltage
Switching frequency
Over V
in
and I
o
ranges
Approvals and
standards
Material flammability
Dimensions
Weight
MTBF
Telcordia SR-332
(L x W x H)
Suffix ‘W’
Suffix ‘L’
See Tables on Page 2
Non-isolated
320 kHz typ.
250 kHz typ.
EN60950
UL/cUL60950
UL94V-0
22.10 x 12.57 x 8.50 mm
0.870 x 0.495 x 0.335 in
2.9 g (0.10 oz)
7,092,000 hours
Temperature co-efficient -40 ºC to +85 ºC
Transient response
(See Note 5)
Margin adjustment
INPUT SPECIFICATIONS
Input voltage range
Input current
Remote ON/OFF
Start-up time
Undervoltage lockout
Track input voltage
Pin 8 (See Note 6)
(See Note 3)
No load
(See Note 1)
70 µs recovery time
Overshoot/undershoot 100 mV
±5.0% Vo
ENVIRONMENTAL SPECIFICATIONS
10.8-13.2 Vdc
10 mA typ.
Positive logic
1 V/ms
8.8-0.4 V typ.
±0.3 Vin
PROTECTION
Short-circuit
Auto reset
14 A typ.
Thermal performance
(See Note 2)
MSL (‘Z’ suffix only)
Operating ambient,
temperature
Non-operating
JEDEC J-STD-020C
-40 ºC to +85 ºC
-40 ºC to +125 ºC
Level 3
International Safety Standard Approvals
UL/cUL CAN/CSA-C22.2 No. 60950-1-03/UL 60950-1,
File No. E174104
TÜV Product Service (EN60950) Certificate No. B 04 06 38572 044
CB Report and Certificate to IEC60950, Certificate No.
US/8292/UL
*Auto-track™ is a trade mark of Texas Instruments
File Name: pth12050.pdf Rev: 6 Nov 2006
12 Vin single output
DC-DC CONVERTERS
POLA Non-isolated2
NEW Product
2
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
OUTPUT
POWER
(MAX.)
33 W
33 W
OUTPUT
CURRENT
(MIN.)
0A
0A
OUTPUT
CURRENT
(MAX.)
6A
6A
PTH12050
INPUT
VOLTAGE
10.8-13.2 Vdc
10.8-13.2 Vdc
OUTPUT
VOLTAGE
0.8-1.8 Vdc
1.2-5.5 Vdc
EFFICIENCY
(MAX.)
88%
93%
REGULATION
LINE
±5 mV
±5 mV
LOAD
±5 mV
±5 mV
MODEL
NUMBER
(9,10)
PTH12050L
PTH12050W
Part Number System with Options
PTH12050WAST
Packaging Options
No Suffix = Trays
T = Tape and Reel
(7)
Mounting Option
(9)
D = Horizontal Through-Hole (Matte Sn)
H = Horizontal Through-Hole (Sn/Pb)
S = Surface-Mount (63/37 Sn/Pb
pin solder material)
Z = Surface-Mount (96.5/3.0/0.5 Sn/Ag/Cu
pin solder material)
Pin Option
A = Through-Hole Std. Pin Length (0.140”)
A = Surface-Mount Tin/Lead Solder Ball
Output Voltage Code
W = Wide. L = Low Voltage
Product Family
Point of Load Alliance
Compatible
Input Voltage
12 = 12 V
Output Current
05 = 6 A
Mechanical Package
Always 0
Output Voltage Adjustment of the PTH12050 Series
The ultra-wide output voltage trim range offers major advantages to users who
select the PTH12050. It is no longer necessary to purchase a variety of modules
in order to cover different output voltages. The output voltage can be trimmed
in a range of 1.2 V to 5.5 V for suffix ‘-W’ and 0.8 V to 1.8 V for suffix ‘-L’.
When the PTH12050 converter leaves the factory the output has been adjusted
to the default voltage of 1.2 V for the PTH12050W and 0.8V for the
PTH12050L.
Notes
Remote ON/OFF. Positive Logic
Pin 3 open; or V > Vin - 0.5 V
ON:
OFF:
Pin 3 GND; or V < 0.8 V (min - 0.2 V).
2
See Figure 1 for safe operating curve.
3
A 100 µF electrolytic input capacitor is required for proper operation. The
capacitor must be rated for a minimum of 750 mA rms of ripple current.
C2 = 10 µF ceramic capacitor, required for output voltages of 3.3 V and
higher.
4
An external output capacitor is not required for basic operation. Adding
100 µF of distributed capacitance at the load will improve the transient
response.
5
1 A/µs load step, 50 to 100% Iomax, Cout = 100 µF.
6
If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point).
7
Tape and reel packaging only available on the surface-mount versions.
8
The pk-pk output ripple voltage is measured with an external 10µF
ceramic capacitor. See Figure 3 Standard application schematic.
9
To order Pb-free (RoHS compatible) surface-mount parts replace the
mounting option ‘S’ with ‘Z’, e.g. PTH12050WAZ. To order Pb-free
(RoHS compatible) through-hole parts replace the mounting option ‘H’
with ‘D’, e.g. PTH12050WAD.
10
NOTICE: Some models do not support all options. Please contact your
local Artesyn representative or use the on-line model number search tool at
http://www.artesyn.com/powergroup/products.htm to find a suitable
alternative.
1
EFFICIENCY TABLE - PTH12050W (I
O
= 5 A)
OUTPUT VOLTAGE
Vo = 5.0 V
Vo = 3.3 V
Vo = 2.5 V
Vo = 2.0 V
Vo = 1.8 V
Vo = 1.5 V
Vo = 1.2 V
EFFICIENCY
93%
91%
89%
88%
87%
86%
84%
EFFICIENCY TABLE - PTH12050L (I
O
= 5 A)
OUTPUT VOLTAGE
Vo = 1.8 V
Vo = 1.5 V
Vo = 1.2 V
Vo = 1.0 V
Vo = 0.8 V
EFFICIENCY
88%
87%
85%
83%
81%
File Name: pth12050.pdf Rev: 6 Nov 2006
12 Vin single output
DC-DC CONVERTERS
POLA Non-isolated
NEW Product
3
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
PTH12050W Characteristic Data
PTH12050
90
80
TEMPERATURE (ºC)
100
70
EFFICIENCY (%)
95
90
85
80
75
70
65
60
60
50
40
30
20
0
1
2
3
4
5
6
OUTPUT CURRENT (A)
Nat Conv
100 LFM
200 LFM
400 LFM
Vout
5.0V
3.3V
2.5V
2.0V
1.8V
1.5V
1.2V
0
1
2
3
4
5
6
OUTPUT CURRENT (A)
Figure 2 - Efficiency vs Load Current for PTH12050W
Vin = 12 V (See Note B)
Figure 1 - Safe Operating Area for PTH12050W
Vin = 12 V, Output Voltage = 3.3 V (See Note A)
PTH12050L Characteristic Data
90
TEMPERATURE (ºC)
100
90
EFFICIENCY (%)
80
70
60
50
40
30
20
0
1
2
3
4
5
6
Nat Conv
100 LFM
80
70
60
50
0
1
2
3
4
5
6
Vout
1.8V
1.5V
1.2V
1.0V
0.8V
OUTPUT CURRENT (A)
OUTPUT CURRENT (A)
Figure 4 - Efficiency vs Load Current for PTH12050L
Vin = 12 V (See Note B)
Figure 3 - Safe Operating Area for PTH12050L
Vin = 12 V, Output Voltage ≤ 1.8 V (See Note A)
Notes
Auto-track
1
2
Vin
3
4
C
in
100µF
(Required)
+
6
Vout
A
SOA curves represent the conditions at which internal components are
within the Artesyn derating guidelines.
B
Characteristic data has been developed from actual products tested at
25 °C. This data is considered typical data for the converter.
PTH12050
(Top View)
5
+
C
out
100µF
(Optional)
Inhibit
R
SET
0.5%, 0.1W
(Required)
GND
GND
Figure 5 -
Standard Application - All Models
File Name: pth12050.pdf Rev: 6 Nov 2006
12 Vin single output
DC-DC CONVERTERS
POLA Non-isolated
NEW Product
4
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
PTH12050
0.140
(3.55)
0.870 (22.10)
0.060
(1.52)
1
0.125
(3.18)
0.125
(3.18)
0.125
(3.18)
2
3
5
4
0.070 (1.78)
(Standoff Shoulder)
0.750 (19.06)
6
0.060
(1.52)
0.040 (1.02)
6 Places
0.375 0.495
(12.57)
(9.52)
Lowest Component
0.010 min. (0.25)
Bottom side Clearance
PIN CONNECTIONS
PIN NO.
FUNCTION
Ground
Track
Vin
Inhibit*
Vo adjust
Vout
TOP VIEW
0.335 (8.50)
MAX.
Dimensions in Inches (mm)
Tolerances (unless otherwise specified)
2 Places
±0.030
(±0.76)
3 Places
±0.010
(±0.25)
SIDE VIEW
1
2
3
4
5
6
Host Board
Figure 6 - Plated Through-Hole Mechanical Drawing
*Denotes negative logic:
Open = Normal operation
Ground = Function active
0.870 (22.10)
0.060
(1.52)
1
2
3
5
4
SIDE VIEW
0.750 (19.06)
0.060
(1.52)
6
0.495
0.375 (12.57)
(9.52)
Solder Ball
0.040 (1.02)
6 Places
0.335 (8.50)
max.*
*After solder reflow
on customer board
0.125
(3.18)
0.125
(3.18)
0.125
(3.18)
TOP VIEW
Dimensions in Inches (mm)
Tolerances (unless otherwise specified)
2 Places ±0.030 (±0.76)
3 Places ±0.010 (±0.25)
Figure 7 - Surface-Mount Mechanical Drawing
Datasheet © Artesyn Technologies® 2006
The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising
from printing errors or inaccuracies. The information and specifications contained or described herein are subject to change in any manner at any time without notice. No rights under any patent
accompany the sale of any such product(s) or information contained herein.
Please consult our website for the following items:
Application Note
www.artesyn.com
File Name: pth12050.pdf Rev: 6 Nov 2006
电子竞赛
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
