3KP5.0 thru 3KP220CA
Transient Voltage Suppressors
Peak Pulse Power 3000W Stand-off Voltage 5.0 to 220V
Features
Plastic package has Underwriters Laboratory Flammability
Classification 94V-O
Glass passivated chip junction in P-600/R-6 package
3000W Peak Pulse Power capability at on 10/1000uS waveform
Excellent clamping capability
Low zener impedance
Repetition rate(Duty Cycle):.05%
Fast response time: typically less than 1.0 ps from 0 volts to BV
min
Typical I
R
less than 1uA above 10V
High temperature soldering guaranteed: 260
o
C/10 seconds/
.375",(9.5mm) lead length/5lbs., (2.3kg) tension
Mechanical Data
Case: JEDEC P600 molded plastic
Terminals: Axial leads, solderable per MIL-STD-750, Method
2026
Polarity: Color band denoted cathode except Bipolar
Mounting Position: Any
Weight: 0.07 ounce, 2.1 grams
For Bidirectional use C or CA Suffix for types 3KP5.0 thru types 3KP220
Electrical characteristics apply in both directions.
Maximum Ratings and Thermal Characteristics
Ratings at 25
o
C ambient temperature unless otherwise specified.
Parameter
Peak Power Dissipation at T
A
=25
o
C, T
P
=1ms
(1)
Symbol
P
PPM
I
PPM
P
M(AV)
(3)
Value
Minimum 3000
See Next Table
8.0
250
-55 to +175
Unit
W
A
W
Amps
o
Peak pulse current with a 10/1000
u
s waveform
(1)
Steady state power dissipation
at T
L
=75
o
C, lead lengths 0.375" (9.5mm)
(2)
Peak forward surge current, 8.3ms single half sine-wave
Operating junction and storage temperature range
I
FSM
T
J
, T
STG
C
Notes:
1. Non-repetitive current pulse, per Fig.3 and derated above T
A
=25
o
C per Fig. 2
2. Mounted on copper pad area of 0.79 x 0.79" (20 x 20 mm) per Fig. 5.
3. Measured on 8.3ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum.
606
Notes:
1. V
(BR)
measured after I
T
applied for 300us, I
T
=square wave pulse or equivalent
2. Surge current waveform per Fig. 3 and derate per Fig. 2
Application:
The 3KP series of high power transient voltage suppressors were designed to be used on the output of switching power supplies. These devices may be used to
replace crowbar circuits. Both the 5 and 10 percent voltage tolerances are referenced to the power supply output voltage level.
They are able to withstand high levels of peak current while allowing a circuit breaker to trip or a fuse blow before shorting. This will enable the user to reset the
breaker or replace the fuse and continue operation. For this type operation, it is recommended that a sufficient mounting surface be used for dissipating the heat
generated by the Transient Voltage Suppressor during the transient or over-voltage condition.
Transient Voltage Suppressors are Silicon PN Junction devices designed for absorption of high voltage transients associated with power disturbances, switching and
induced lighting effects. This series is available from 5.0 volts thru 220 volts.
RATINGS AND CHARACTERISTIC CURVES
(T
A
= 25
o
C unless otherwise noted)
609
DSP 与 ARM 处理器
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
