Pletronics, Inc.
19013 36 Ave. West PO Box 2607 Lynnwood, Washington
98036 U.S.A.
T: 1-425-776-1880
F: 1-425-776-2760 E: ple-sales@pletronics.com
www.pletronics.com
th
Effective January 1, 2008
The SM11xxB series is discontinued.
This has been discontinued because:
•
the difficulty of the older design to assemble well in the newer RoHS compliant high
temperature reflow processes.
•
the cover assembly was not meeting some of the cleaning and assembly needs of the newer
processes.
•
the components needed to make these parts are no longer available.
This requirement is best met by using an SM77xxD 5x7mm SMD oscillator.
Pl tronics, Inc.
.
19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA
Manufacturer of High Quality Frequency Control Products
SM1145BD CMOS Series
CMOS with Enable/ Disable, 3rd Overtone Crystal Used
Low Jitter
4 Pad Surface Mount Clock Oscillator
Standard Specifications
Overall Frequency Stability
Operating Temperature Range
Supply Voltage (Vcc)
Symmetry (Duty Cycle)
Logic Levels
Jitter
Output Load
Enable/Disable Option (E/D)
SM1145BD: ± 50 PPM, SM1144BD: ± 25 PPM, SM1120BD: ± 20 PPM over Operating Temp. Range
0 to +70°C is standard, but can be extended to
−
40 to +85°C for certain frequencies
5.0 volts, 3.3 volts, and 2.5 volts available, consult factory for 1.8 volts
40/60 to 60/40% is standard, but 45/55% at 50% of Vcc is also available (see Waveform 1)
Logic “1”
90% of Vcc MIN;
Logic “0”
10% of Vcc MAX
1 pS RMS maximum,
from 12 kHz to 20 MHz from carrier
Standard load is 15pF (typ. 1 ASIC) maximum, see Test Circuit 3 (consult factory for
heavier
loads)
Output enabled when Pin #1 is open or at Logic “1”; Output disabled when Pin #1 is at Logic “0”.
70.00 MHz
–
170.00 MHz
Solder Pad Compatible to our SM11 Series, Epson SG615 & SG8002J
Consult factory for
higher
frequencies
See Website for Supply Current (Icc) and Rise and Fall Times
Part Numbering Guide
Portions of the part number that appear after the frequency may not be marked on part (C of C provided)
SM11 45 BD V - 70.0M - 30 - XXX
(Internal Code or blank)
Packaging
Tube or
24mm tape
16mm pitch
Model
Frequency Stability
45 = ± 50 PPM
44 = ± 25 PPM
20 = ± 20 PPM
Non-Std Output Load
Blank = 15 pF max, 30 = 30 pF max
Frequency in MHz
Special Specifications (choose all that apply)
Y: Std Specs (5.0V
± 10%,
0 to +70
°
C, 40/60% Symmetry)
E: Extended Operating Temperature Range (- 40 to +85
°
C)
S: 45/55% Symmetry at 50% of Vcc
V: Supply Voltage of 3.3 volts
± 10%
W: Supply Voltage of 2.5 volts ±
5%
X:
Supply Voltage of 1.8 volts ±
5% (Consult factory)
Consult factory for available frequencies and specs. Not all options available for all frequencies. A special part number may be assigned.
Frequency Stability is inclusive of frequency shifts due to calibration, temperature, supply voltage, shock, vibration and load
Mechanical: inches (mm)
not to scale
Solder Pads
0.200 (5.08)
Due to part size and factory abilities, part marking may vary from lot to lot and may contain our part number or an internal code.
PIN
0.400 (10.16) MAX
0.118 0.228 (5.8)
(3.0)
4
3
SIGNAL
E/D
GND
OUT
Vcc
3
4
1
2
3
4
2
1
1
2
0.560 (14.23) MAX
0.195 (4.95)
MAX
0.200 (5.08)
Pl tronics, Inc.
(425) 776 -1880, Fax: (425) 776-2760, ple-sales@pletronics.com, www.pletronics.com
0.055 0.145
(1.4) (3.68)
Sept 2004
9
CMOS
70 - 170 MHz, 3rd OT
Page 8 - 11
PCB设计
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
