Obsolescence Notice
This product is obsolete.
This information is available for your
convenience only.
For more information on
Zarlink’s obsolete products and
replacement product lists, please visit
http://products.zarlink.com/obsolete_products/
APRIL 1995
MA5104
DS3580-3.2
MA5104
RADIATION HARD 4096 x 1 BIT STATIC RAM
The MA5104 4k Static RAM is configured as 4096 x 1 bits and
manufactured using CMOS-SOS high performance, radiation hard,
3µm technology.
The device has separate input and output terminals controlled by
Chip Select and Write Enable. The design uses a 6 transistor cell and
has full static operation with no clock or timing strobe required.
Address input buffers are deselected when Chip Select is in the HIGH
state.
Operation Mode
Read
Write
Standby
CS
L
L
H
WE
H
L
X
I/O
D OUT
D IN
High Z
ISB2
Power
ISB1
FEATURES
s
3µm CMOS-SOS Technology
s
Latch-up Free
s
Fast Access Time 90ns Typical
s
Total Dose 10
6
Rad(Si)
s
Transient Upset >10
10
Rad(Si)/sec
s
SEU <10
-10
Errors/bitday
s
Single 5V Supply
s
Three State Output
s
Low Standby Current 10µA Typical
s
-55°C to +125°C Operation
s
All Inputs and Outputs Fully TTL or CMOS
Compatible
s
Fully Static Operation
Figure 1: Truth Table
Figure 2: Block Diagram
1
MA5104
CHARACTERISTICS AND RATINGS
Symbol
V
CC
V
I
T
A
T
S
Parameter
Supply Voltage
Input Voltage
Operating Temperature
Storage Temperature
Min.
-0.5
-0.3
-55
-65
Max.
7
V
DD
+0.3
125
150
Units
V
V
°C
°C
Stresses above those listed may cause permanent
damage to the device. This is a stress rating only and
functlonal operation of the device at these condltions,
or at any other condition above those indicated in the
operations section of this specification, is not Implied
Exposure to absolute maxlmum rating conditions for
extended perlods may affect device reliability.
Figure 3: Absolute Maximum Ratings
Notes for Tables 4 and 5:
1. Characteristics apply to pre radiation at T
A
= -55°C to +125°C with V
DD
= 5V
±10%
and to post 100k Rad(Si) total dose
radiation at T
A
= 25°C with V
DD
= 5V
±10%
(characteristics at higher radiation levels available on request).
2. Worst case at T
A
= +125°C, guaranteed but not tested at T
A
= -55°C.
GROUP A SUBGROUPS 1, 2, 3.
Symbol
V
DD
V
lH
V
lL
V
OH
V
OL
I
LI
I
LO
I
PUI
I
PDI
I
DD
I
SB1
I
SB2
Parameter
Supply voltage
Input High Voltage
Input Low Voltage
Output High Voltage
Output Low Voltage
Input Leakage Current (note 2)
Output Leakage Current (note 2)
Input Pull-Up Current
Input Leakage Current
Power Supply Current
Selected Supply Current
Standby Supply Current
Conditions
-
-
-
I
OH1
= -1mA
I
OL
= 2mA
All inputs except
CS
Output disabled, V
OUT
= V
SS
or V
DD
V
IN
= V
SS
on
CS
input only
V
IN
= V
SS
on
CS
input only
f
RC
= 1MHz,
CS
= 50% mark:space
CS
= V
SS
Chip disabled
Min.
4.5
V
DD
/2
V
SS
2.4
-
-
-
-
-
-
-
-
Typ.
5.0
-
-
-
-
-
-
-
-
12
25
50
Max.
5.5
V
DD
0.8
-
0.4
±10
±20
-100
5
16
35
3000
Units
V
V
V
V
V
µA
µA
µA
µA
mA
mA
µA
Figure 4: Electrical Characteristics
Symbol
V
DR
I
DDR
Parameter
V
CC
for Data Retention
Data Retention Current
Conditions
CS
= V
DR
CS
= V
DR
, V
DR
= 2.0V
Min.
2.0
-
Typ.
-
30
Max.
-
2000
Units
V
µA
Figure 5: Data Retention Characteristics
2
MA5104
AC CHARACTERISTICS
Conditions of Test for Tables 5 and 6:
1. Input pulse = V
SS
to 3.0V.
2. Times measurement reference level = 1.5V.
3. Transition is measured at
±500mV
from steady state.
4. This parameter is sampled and not 100% tested.
Notes for Tables 6 and 7:
Characteristics apply to pre-radiation at T
A
= -55°C to +125°C with V
DD
= 5V±10% and to post 100k Rad(Si) total dose radiation
at T
A
= 25°C with V
DD
= 5V
±10%.
GROUP A SUBGROUPS 9, 10, 11.
Symbol
T
AVAVR
T
AVQV
T
ELQV
T
ELQX
(4)
T
ELQZ
(4)
T
AXQX
Parameter
Read Cycle Time
Address Access Time
Chip Select to Output Valid
Chip Select to Output Active
Chip Select to Output Tri State
Output Hold from Address Change
Min
135
-
-
10
10
10
Max
-
135
135
-
50
-
Units
ns
ns
ns
ns
ns
ns
Figure 6: Read Cycle AC Electrical Characteristics
Symbol
T
AVAVW
T
AVWL
T
WLWH
T
WHAV
T
DVWH
T
NHDX
T
WLQZ
(4)
T
ELWL
T
ELWH
T
AVWH
T
WHQX
(4)
Parameter
Write Cycle Tlme
Address Set Up Time
Write Pulse Width
Write Recovery Time
Data Set Up Time
Data Hold Time
Write Enable to Output Tri State
Chip Selection to Write Low
Chip Selection to End of Write
Address Valid to End of Write
Output Active from End to Write
Min
135
10
50
5
35
5
10
25
85
80
5
Max
-
-
-
-
-
-
50
-
-
-
-
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Figure 7: Write Cycle AC Electrical Characteristics
Symbol
C
IN
C
OUT
Parameter
Input Capacitance
Output Capacitance
Conditions
V
l
= 0V
V
O
= 0V
Min.
-
-
Typ.
6
8
Max.
10
12
Units
pF
pF
Note: T
A
= 25°C and f = 1MHz. Data obtained by characterisation or analysis; not routinely measured.
Figure 8: Capacitance
3
MA5104
Symbol
F
T
Parameter
Basic Functionality
Conditions
V
DD
= 4.5V - 5.5V, FREQ = 1MHz
V
IL
= V
SS
, V
IH
= V
DD
, V
OL
≤
1.5V, V
OH
≥
1.5V
TEMP = -55°C to +125°C, GPS PATTERN SET
GROUP A SUBGROUPS 7, 8A, 8B
Figure 9: Functionality
Subgroup
1
2
3
7
8A
8B
9
10
11
Definition
Static characteristics specified in Tables 4 and 5 at +25°C
Static characteristics specified in Tables 4 and 5 at +125°C
Static characteristics specified in Tables 4 and 5 at -55°C
Functional characteristics specified in Table 9 at +25°C
Functional characteristics specified in Table 9 at +125°C
Functional characteristics specified in Table 9 at -55°C
Switching characteristics specified in Tables 6 and 7 at +25°C
Switching characteristics specified in Tables 6 and 7 at +125°C
Switching characteristics specified in Tables 6 and 7 at -55°C
Figure 10: Definition of Subgroups
4
开关电源学习小组
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
