FUJITSU SEMICONDUCTOR
DATA SHEET
DS07-12538-1E
8-bit Proprietary Microcontroller
CMOS
F MC-8L MB89990 Series
MB89997
s
OUTLINE
The MB89990 series microcontrollers contain various resources such as timers, external interrupts, and remote-
control functions, as well as an F
2
MC*-8L CPU core for low-voltage and high-speed operations. These single-
chip microcontrollers are suitable for small devices such as remote controllers incorporating compact packages.
*: F
2
MC stands for FUJITSU Flexible Microcontroller.
2
s
FEATURES
• Minimum execution time: 0.95
µs
at 4.2 MHz (V
CC
= 2.7 V)
• F
2
MC-8L family CPU core
• Two timers
8/16-bit timer/counter
20-bit timebase counter
(Continued)
s
PACKAGE
28-pin Plastic SOP
28-pin Plastic SH-DIP
48-pin Ceramic MQFP
(FPT-28P-M17)
(DIP-28P-M03)
(MQP-48C-P01)
MB89990 Series
(Continued)
• External interrupts
Edge detection (Edge selection enabled): 3 channels
Low-level interrupt (Wake-up function): 8 channels
• Internal remote-control transmission frequency generator
• Low-power consumption modes
Stop mode (Almost no current consumption occurs because oscillation stops.)
Sleep mode (The current consumption is about 1/3 of that during normal operation because the CPU stops.)
• Packages
SOP-28 and SH-DIP-28
s
PRODUCT LINEUP
Part number
MB89997
Item
Classification
ROM size
32 K
×
8 bits
(internal mask ROM)
RAM size
CPU functions
128
×
8 bits
The number of basic instructions:
Instruction bit length:
Instruction length:
Data bit length:
Minimum execution time:
Interrupt processing time:
I/O port (N channel open drain):
I/O port (CMOS):
Total:
Mass-produced products
(mask ROM products)
One-time PROM product
16 K
×
8 bits
(internal PROM, to be
programmed with general-
purpose EPROM
programmer)
256
×
8 bits
136
8 bits
1 to 3 bytes
1, 8, and 16 bits
0.95
µs
at 4.2 MHz
8.57
µs
at 4.2 MHz
6
16 (13 serves as resources)
22
For development and
evaluation
32 K
×
8 bits
(external ROM)
MB89P195*
1
MB89PV190*
2
Ports
8/16-bit timer/
counter
External interrupt 1
2 channels for 8-bit timer counter or for 16-bit event counter (operation clock: 1.9
µs,
30.4
µs,
and 487.6
µs
at 4.2 MHz, and external clock)
3 independent channels (edge selection, interrupt vector, and interrupt source flag)
Rising edge/falling edge/both edge selectability
Used for wake-up from stop/sleep mode. (Edge detection is also permitted in stop mode.)
8 channels (low-level interrupt only)
External interrupt 2
(Wake-up function)
Remote-control
transmission
frequency
generation
The pulse width and cycle are software-programmable.
(Continued)
2
MB89990 Series
(Continued)
Part number
MB89997
Item
Low-power
consumption
(standby mode)
Process
Power supply
voltage*
3
EPROM for use
2.2 V to 6.0 V
Sleep mode and stop mode
CMOS
2.7 V to 6.0 V
MBM27C256A-20TVM
MB89P195*
1
MB89PV190*
2
*1 : The MB89P195 microtroller is the one-time product for the MB89190 series which can be also be used for the
MB89990 series.
*2 : The MB89PV190 microtroller is the evaluation and development product for the MB89190 series which can
be also be used for the MB89990 series.
*3 : Varies with conditions such as operating frequencies (see “s Electrical Characteristics.”)
s
PACKAGE AND CORRESPONDING PRODUCTS
Package
DIP-28P-M03
FPT-28P-M17
MQP-48C-P01
: Available
×
×
MB89997
MB89P195
×
MB89PV190
×
×
*
×
: Not available
* : A socket (manufacturer: Sun Hayato Co., Ltd.) for pin pitch conversion is available.
480F-28SOP-8L: (MQP-48C-P01)
→
for conversion to FPT-28P-M02
Inquiry: Sun Hayato Co., Ltd.: TEL: (81)-3-3986-0403
FAX: (81)-3-5396-9106
Note: For more information on each package, see “s Package Dimensions.”
3
MB89990 Series
s
DIFFERENCES AMONG PRODUCTS
1. Memory Size
Before evaluating using the piggyback model, verify its difference from the model that will actually be used.
Take particular care on the following points:
• On the MB89997, addresses 0140
H
to 0180
H
cannot be used for register banks.
• The stack area, etc., is set in the upper limit of the RAM.
2. Current Consumption
• In the case of MB89PV190, add the current consumed by the EPROM which is connected to the top socket.
• When operated at low speed, a model with an OTPROM (EPROM) will consume more current than a model
with a mask ROM.
However, current consumption in the sleep/stop mode in the same. (For more information, see “s Electrical
Characteristics.”)
3. Mask Options
Functions that can be selected as options and how to designate these options vary by model.
Before using options check “s Mask Options.”
Take particular care on the following points:
• The power-on reset option is fixed as “enabled” for MB89P195.
• Options are fixed on the MB89PV190.
4
MB89990 Series
s
PIN ASSIGNMENT
(Top view)
P04/INT24
P05/INT25
P06/INT26
P07/INT27
TEST
RST
X0
X1
V
SS
P37/RCO
P36/INT12
P35/INT11
P34/TO/INT10
P33/EC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
V
CC
P03/INT23
P02/INT22
P01/INT21
P00/INT20
P45
P44
P43
P42
P41
P40
P30
P31
P32
(FPT-28P-M17)
(DIP-28P-M03)
5
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
