AMPLIMITE* HD-22
Right-Angle Front
Metal Shell Connectors
Application Specification
114-13198
03 MAY 07
Rev A
NOTE
i
All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and
inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2 .
Figures and illustrations are for identification only and are not drawn to scale.
_
1. INTRODUCTION
This specification covers the requirements for application of AMPLIMITE HD 22 Right–Angle Front Metal Shell
Series 350 Connectors. The series designator is the dimension from the front of the connector flange to the
center of the first solder–tail. The connectors are available with boardlocks in the mounting legs and 4–40
threaded inserts or 4–40 female screwlocks in the mounting flanges.
The connectors are available in 15, 26, 44, 62, and 78 positions, with shell sizes of 1 through 5 respectively.
Each connector is marked with position numbers on the mating faces for circuit identification. The connector
plugs contain pin contacts and the receptacles contain socket contacts. These pre–installed right–angle
contacts have precision formed solder–tails. This document supercedes Application Specification 114–40021.
Figure 1 provides connector features and terms used throughout this specification. Use these terms when
corresponding with Tyco Electronics Representatives to facilitate assistance.
Nonremovable
Screwlock (Ref)
Grounding Indents
Mounting
Flange
Housing
Mating Face
Plug
Mounting Leg
Threaded Insert
Series
Designator
Dimension
Boardlock
Solder-Tails
Receptacle
Recessed Cavity
Position Identification
Boardlock
(Ref)
Figure 1
E
2007 Tyco Electronics Corporation, Harrisburg, PA
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at
www.tycoelectronics.com
1
of 11
LOC B
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
AMPLIMITE HD-22 Right-Angle Front Metal Shell Connectors
2. REFERENCE MATERIAL
2.1. Revision Summary
114-13198
This paragraph is reserved for a revision summary covering the most recent additions and changes made to
this specification which include the following:
S
Initial release of document
2.2. Customer Assistance
Reference Base Part Number 5749771 and Product Code 4519 are representative numbers of AMPLIMITE
HD 22 Right–Angle Front Metal Shell Connectors. Use of these numbers will identify the product line and
expedite your inquiries through a service network established to help you obtain product and tooling
information. Such information can be obtained through a local Tyco Electronics Representative or, after
purchase, by calling the Tooling Assistance Center or the Product Information number at the bottom of page 1.
2.3. Drawings
Customer Drawings for each product part number are available from the service network. The information
contained in Customer Drawings takes priority if there is a conflict with this specification or with any technical
documentation supplied by Tyco Electronics.
2.4. Manuals
Manual 402–40 is available upon request and can be used as a guide in soldering. This manual provides
information on various flux types and characteristics along with the commercial designation and flux removal
procedures. A checklist is included in the manual as a guide for information on soldering problems.
2.5. Specifications
Product Specification 108–1092 provides test information and performance requirements.
3. REQUIREMENTS
3.1. Storage
A. Ultraviolet Light
Prolonged exposure to ultraviolet light may deteriorate the chemical composition used in connectors.
B. Shelf Life
The connectors should remain in the shipping containers until ready for use to prevent damage. The
products should be used on a first in, first out basis to avoid storage contamination that could adversely
affect signal transmissions.
C. Chemical Exposure
Do not store connectors near any chemicals listed below, as they may cause stress corrosion cracking in
the components.
Alkalies
Amines
NOTE
Ammonia
Carbonates
Citrates
Nitrites
Phosphates Citrates
Sulfur Nitrites
Sulfur Compounds
Tartrates
Where the above environmental conditions exist, phosphor-bronze contacts are recommended instead of brass if
available.
i
3.2. Connector Shell Size
The AMPLIMITE Metal Shell Connectors shell sizes conform to industry standard sizes. A composite of
comparable receptacle configurations is provided in Figure 2.
2 of 11
Tyco Electronics Corporation
Rev A
AMPLIMITE HD-22 Right-Angle Front Metal Shell Connectors
114-13198
54.84
[2.159]
52.43
[2.064]
38.38
[1.511]
24.66
[.971]
16.33
[.643]
Receptacle Shell Sizes:
Figure 2
3.3. Mounting Panel Cutout
Panel mounting is optional for AMPLIMITE HD 22 Right–Angle Front Metal Shell Connectors. For pc board
connectors, it will provide additional support for the solder joints during mating and unmating. PC board
connectors can ONLY be rear mounted. Either front or rear mounting is acceptable for the cable connector.
The connector mounting flanges may have 4–40 internal threads that will accept screwlocks or panel mounting
hardware. Hardware attached to the connector flange shall be tightened to 0.45 N
D
m (4 in–lb) maximum. See
Figure 3 for panel cutout dimensions.
Screwlocks are designed to secure a connector to a panel 1.58 mm [.062 in.] thick. They can be used with
thinner panels; however, washers are recommended to make up the thickness difference and provide a
bottoming surface for the mating connector flange. Screwlocks should be tightened to a torque of 0.45 N
D
m (4
in–lb) maximum. The 4–40 internal threads in the screwlocks will accept commercially available screws and
jackscrews.
A
C
F
D
10
_
+2
_
(2 Places)
E
3.35 [.132]
Radius (4 Places)
B
G + 0.05 [.002]
(2 Places)
CONN
SHELL
SIZE
1
2
3
4
5
24.99
DIMENSIONS
G
A
B
C
D
E
F
WITH
SCREWLOCKS
WITHOUT
SCREWLOCKS
[.984]
12.50
16.66
23.52
[.492]
[.656]
[.926]
20.47
[.806]
10.24
14.40
21.26
[.403]
[.567]
[.837]
11.40 [.449]
11.40 [.449]
11.40 [.449]
11.40 [.449]
14.10 [.555]
5.72 [.225]
5.72 [.225]
5.72 [.225]
5.72 [.225]
7.06 [.278]
5.74 [.226]
3.05 [.120]
33.32 [1.312]
47.04 [1.852]
63.50 [2.500]
61.11 [2.406]
28.80 [1.134]
42.52 [1.674]
59.08 [2.326]
56.34 [2.218]
31.75 [1.250]
30.56 [1.203]
29.54 [1.163]
28.17 [1.109]
Figure 3
Rev
A
Tyco Electronics Corporation
3
of 11
AMPLIMITE HD-22 Right-Angle Front Metal Shell Connectors
3.4. Mating Dimension
A. Pin-to-Socket
114-13198
The mating pin configuration must be in accordance with Military Specification MIL–C–39029. See
Figure 4, View A, for dimensions.
B. Connector-to-Connector
The dimension in Figure 4, View B, is required to ensure full mating of connectors. This dimension must
be considered when determining the method of mounting and the thickness of a panel when the connector
is to be panel–mounted.
0.76 + 0.04
[.030 +.002]
(Dia.)
0.20 [.008]
R (Min.)
Free-Hanging
Plug (Ref)
6.73 + 0.38 [.265 +.015]
(For 15- and 26-Position)
or 6.50 + 0.38 [.256 +.015]
(For 44-, 62-, and 78-Position)
PC Board
Receptacle
(Ref)
0.38 [.015] Flat
View A
(Contact Pin Tip Shown
Enlarged for Clarity)
(Max.)
PC Board
View B
(Mated Connectors)
Figure 4
3.5. Connector Spacing
Care must be used to avoid interference between adjacent connectors and/or other components. The
dimension is dependent on variable hardware used and the clearance required for mating connectors. The
information provided in Figure 5 is to ensure proper mating for manual placement of connectors.
Mounting Hole
PC Board
(Ref)
Dimension (Variable)
Figure 5
3.6. PC Boards
A. Material and Thickness
1. Board material will be glass epoxy (FR–4, G–10).
2. Board thickness shall be 1.57 mm [.062 in.] for AMPLIMITE HD 22 Right–Angle Front Metal Shell
Connectors with boardlocks.
Contact the Product Information Center or the Tooling Assistance Center number listed at the bottom of
page 1 for suitability of other board materials or thicknesses.
B. Tolerance
Maximum allowable bow of the pc board shall be 0.03 mm [.001 in.] over the length of the connector.
4
of 11
Tyco Electronics Corporation
Rev
A
AMPLIMITE HD-22 Right-Angle Front Metal Shell Connectors
C. PC Board Layout
114-13198
The mounting and contact holes in the pc board must be precisely located to ensure proper placement and
optimum performance of the connector. The connectors can be placed on the pc board manually. The
following dimensions must be observed when preparing a pc board for AMPLIMITE HD 22 Right–Angle
Front Metal Shell Connectors. See Figure 6.
-Y-
-X-
Posn 1
Connector Mating Face on this Side
62
44
PC Board
Edge
A
15
2.54
[.100]
26
B
(Typ)
D
1.19 +0.05 [.047 +.002] (Typ)
2.54
[.100]
0.15 [.006] M
X
Y
C
3.18 +0.08 [.125 +.003] (Typ)
0.10 [.004] M
X
Y
Layout for 15, 26, 44, and 62 Position Connectors
-Y-
-X-
Connector Mating Face on this Side
Posn 1
78
A
D
PC Board
Edge
2.54
[.100]
B
(Typ)
2.54
2.54
[.100]
[.100]
1.19 +0.05 [.047 +.002] (Typ)
0.15 [.006] M
X
Y
C
3.18 +0.08 [.125 +.003] (Typ)
0.10 [.004] M
X
Y
Layout for 78 Position Connectors
CONNECTOR
SHELL SIZE
1
2
3
4
5
NOTE:
DIMENSIONS
A
7.04 [.277]
6.88 [.271]
6.88 [.271]
7.01 [.276]
7.65 [.301]
POSITIONS
15
26
44
62
78
B
2.29 [.090]
2.29 [.090]
2.29 [.090]
2.41 [.095]
2.41 [.095]
C
24.99 [.984]
33.32 [1.312]
47.04 [1.852]
63.50 [2.500]
61.11 [2.406]
D
1.14 [.045]
1.14 [.045]
1.14 [.045]
1.22 [.048]
1.22 [.048]
The pc board layout shown is for receptacle connectors. The pc board layout for plug connectors is a mirror image of the layout shown.
Figure 6
Rev
A
Tyco Electronics Corporation
5
of 11
下载中心专版
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
