characteristics. The use of piezoelectric polymer film in
the ACH-01 provides many cost/performance advantages
that allow it to be used in a wide range of applications
where the use of traditional accelerometer technology is
impractical. It is specifically designed for high volume
applications which require the permanent installation of
an accelerometer.
FEATURES
Wide Frequency Response
Excellent Phase Response
Small Temperature Dependence
Wide Supply Voltage Range
Excellent Linearity
Very High Resonant Frequency
Wide Dynamic Range
Low Transverse Sensitivity
Wide Temperature Range
Low Impedance Output
Ultra Low Power
APPLICATIONS
Machine Health Monitoring
Model Analysis
Automotive Sensors
Appliances
Feedback Control Systems
SENSOR SOLUTIONS
/// ACH 01 Rev 1
07/2017
Page 1
ACCELEROMETER ACH-01
PERFORMANCE SPECIFICATIONS
PERFORMANCE (T=25C)
Sensitivity
Lower Frequency Limit (1)
Upper Frequency Limit(1)
Equivalent Noise Floor
10Hz
100Hz
1kHz
Dynamic Range
Linearity
Transverse Sensitivity
Resonant Frequency
Phase Deviation (5 Limit)(6)
Drain Voltage (6)
Supply Current (6)
Output Impedance (6)
--
--
M
t
f
o
θ
V+
l
dss
--
Symbol
M
o
f
l
f
u
Min
7
--
10
--
--
--
150
--
--
--
10
3
30
--
Typ
9
2
20
130
20
6
--
0.1
2.0
35
--
--
--
20
Max
11
5
--
--
--
--
--
1.0
5
--
10
40
90
--
Units
mV/g
Hz
kHz
g/ Hz
g
%
%
kHz
kHz
Volts
μA
kΩ
ENVIRONMENTAL CHARACTERISTICS
Operating Temperature (2)
Storage Temperature
Maximum Shock Level
Base Strain Sensitivity (3)
Transient Temp Sensitivity (4)
PHYSICAL CHARACTERISTICS
Weight (5) Cable
(1)
3
dB limit
(2)
2
dB from nominal M
o
at 1kHz
W
--
(3) @ 250με in base plane
(4) @ 3Hz LLF
8
--
grams
T
o
T
s
A
m
--
--
-40
-40
1000
--
--
--
--
--
0.3
0.35
85
85
--
--
--
C
C
g
g/με
g/C
(5) Includes 40" cable and connector
(6) Typical Value
SENSOR SOLUTIONS
/// ACH 01 Rev 1
07/2017
Page 2
ACCELEROMETER ACH-01
Mounting methods play a critical role in determining the overall performance of any accelerometer. The ACH-01 is
no exception. An improperly mounted accelerometer can give erroneous results. We recommend using an Adhesive
Mounting Method.
The surface should be flat. The area where the ACH-01 is to be mounted should be thoroughly cleaned to remove
any dirt or oil present on the surface. Use a quick setting, viscous methyl cyanoacrylate adhesive such as Loctite's
Black MaxJ or any epoxy such as Devcon's 5-Minute epoxy. Apply the adhesive sparingly to one surface following
the manufacturer's directions. Apply pressure and allow the adhesive to set. Soft adhesives, such as double-sided
tape or pressure sensitive adhesives, should not be used since they can adversely affect the ACH-01's
performance. Cable should be adhered to the surface.
There is an interface amplifier available to simplify connection to the ACH-01, the IB-ACH-01. Please see the
appropiate data sheet.
In an effort to keep the product cost low, the ACH-01 uses a ceramic substrate as the mounting base. Because of
this, the ACH-01 is susceptible to base strain and temperature transient effects. A mechanically rigid and thermally
non-conductive mounting surface is highly recommended to limit these effects. MEAS application engineers are
available to recommend various mounting arrangements for your specific application.
ELECTRICAL INTERFACE CIRCUITS
The accelerometer ACH-01 accommodates various electrical interface circuits. A typical example is provided in the
following figure. The ACH-01 equivalent electrical schematic is also shown.
SENSOR SOLUTIONS
/// ACH 01 Rev 1
07/2017
Page 3
ACCELEROMETER ACH-01
The information in this sheet has been carefully reviewed and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Furthermore, this
information does not convey to the purchaser of such devices any license under the patent rights to the manufacturer. Measurement Specialties, Inc. reserves the right
to make changes without further notice to any product herein. Measurement Specialties, Inc. makes no warranty, representation or guarantee regarding the suitability
of its product for any particular purpose, nor does Measurement Specialties, Inc. assume any liability arising out of the application or use of any product or circuit and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications.
All operating parameters must be validated for each customer application by customer’s
technical experts. Measurement Specialties, Inc. does not convey any license
under its patent rights nor the rights of others.
ORDERING INFORMATION
Description
Accelerometer
Interface
Pins
Shielded Cable
Discrete Wires
Model No.
ACH-01-02
ACH-01-03
ACH-01-04
IB-ACH-01
Part No.
0-1000985-0
1-1001220-0
1-1001497-0
1003058
Amplifier
Amplifier Box
NORTH AMERICA
Measurement Specialties, Inc.,
a TE Connectivity Company
Tel: +1-800-522-6752
Email:
customercare.dtmd@te.com
EUROPE
MEAS Deutschland GmbH
a TE Connectivity Company
Tel: +49-800-440-5100
Email:
customercare.dtmd@te.com
ASIA
Measurement Specialties (China), Ltd.,
a TE Connectivity Company
Tel: +86 0400-820-6015
Email:
customercare.chdu@te.com
TE.com/sensorsolutions
Measurement Specialties, Inc., a TE Connectivity company.
Measurement Specialties, TE Connectivity, TE Connectivity (logo) and EVERY CONNECTION COUNTS are trademarks. All other logos, products and/or company names referred to herein
might be trademarks of their respective owners.
The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes
no warranties as to its accuracy or completeness and disclaims any liability in connection with its
use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard
Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse
of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application.
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
