SMD POWER RESISTORS AEC-Q200 QUALIFIED
Type 3521 Series
Key Features
2 Watts at
70°C
Small size to
power ratio
Supplied on
tape
Value marked
on resistor
500 volt
maximum
overload
250 volt
maximum
working
voltage
Terminal finish
matte Sn over
Ni
AEC-Q200
Qualified
TE Connectivity is pleased to announce that our 3521 series high power Thick Film
Chip Resistor is now AEC-Q200 Qualified. This low cost device, suitable for auto
placement in volume, and for most applications, including high frequency
operations, owing to the short lead structure, is attractively priced and available on
7" reels of 4000 pieces.
Characteristics
–
Electrical
Power Rating
Resistance Range
Tolerance
Max. Working Voltage
Max. Overload Voltage
Dielectric Withstanding Voltage
Temperature Range
Ambient Temperature
2W
0.1Ω ~ 10MΩ
±1% ±5%
250V
500V
500V
-55°C
½
+155°C
70°C
Resistors shall have a power rating based on continuous load operation at an
ambient temperature of 70
℃
. For temperature in excess of 70
℃
, The load shall be
derated as shown below:
9-1773463-5 Rev G 02/2020
Dimensions in
millimetres unless
otherwise specified
Dimensions Shown for
reference purposes only.
Specifications subject to
change
For Email, phone or live chat,
go to: www.te.com/help
SMD POWER RESISTORS AEC-Q200 QUALIFIED
Voltage Rating:
Resistors shall have a rated direct-current (DC) continuous working voltage or
an approximate sine-wave root-mean-square (RMS) alternating-current (AC)
continuous working voltage at commercial line frequency and waveform
corresponding to the power rating , as determined from the following formula:
RCWV
Where:
RCWV =
Rated DC or RMS AC continuous working voltage at
commercial-line frequency and waveform (volt)
P
R
=
=
Power Rating (watt)
Nominal Resistance (ohm)
=
√P
x R
In no case shall the rated DC or RMS AC continuous working voltage be greater
than the applicable maximum value.
Construction & Dimensions:
Dimensions: (mm)
L
W
6.35±0.10
3.20±0.20
H
0.55±0.10
ℓ
0.60±0.25
ℓ
0.50±0.20
9-1773463-5 Rev G 02/2020
Dimensions in
millimetres unless
otherwise specified
Dimensions Shown for
reference purposes only.
Specifications subject to
change
For Email, phone or live chat,
go to: www.te.com/help
SMD POWER RESISTORS AEC-Q200 QUALIFIED
Recommended solder pad
A
Width
(mm)
3.0
B
Pad (mm)
1.5
C
Spacing
(mm
5.0
4 layers PCB specification:
1) Outside 2 layers (Top and Bottom) with copper foil thickness at 2oz.
2) Inside 2 layers (Middle layers) with copper foil thickness at 4 oz.
Marking:
For E24 series Values three digit marking, the first two digits are significant
figures and the third denoting number of zeros.
E.G.
333
Ω
KΩ
For Oh i Values elo
E.G.
3R3
. Ω
For E96 Values four digit marking, the first three showing significant figures
and the fourth showing number of zeros. As previously letter R is for decimal
point.
E.G.
4992
49K9Ω
9-1773463-5 Rev G 02/2020
Dimensions in
millimetres unless
otherwise specified
Dimensions Shown for
reference purposes only.
Specifications subject to
change
For Email, phone or live chat,
go to: www.te.com/help
SMD POWER RESISTORS AEC-Q200 QUALIFIED
Performance Specification:
Characteristics
Operational life
Limits
± %+ . Ω
<
Ω
a
Test Methods
125°C, at 35% of operating power, 1000H
. hours ON , . hour OFF .
(MIL-STD-202)
Apply to rate current for 0Ω
Parametrically test per lot and sample size
requirements, summary to show Min, Max,
Mean and Standard deviation at room as
well as Min and Max operating
temperatures. (User Spec)
Electrical test not required. Inspect device
construction, marking and workmanship
(MIL-STD-883 Method 2009)
Verify physical dimensions to the applicable
device detail specification.
Note: User(s) and Suppliers spec. Electrical
test not required.
(JESD22 MH Method JB-100)
Note: Add Aqueous wash chemical
–
OKEM
Clean or equivalent.
Do not use banned solvents.
( MIL-STD-202 Method 215)
Force of 1.8kg for 60 seconds.
(JIS-C-6429)
1000hrs. @T=155°C.Unpowered.
Measurement at 24±2 hours after test
conclusion.
(MIL-STD-202 Method 108)
Appl to rate urre t for Ω
1000 Cycles (-55°C to +155°C). Measurement
at 24±2 hours after test conclusion
(JESD22 Method JA-104)
Appl to rate urre t for Ω
Electrical
Characterisation
. Ω<R≤ .
Ω
±100PPM
Ω
≦
R
≤ Ω ≤±
PPM/°C
Ω<R
≦
Ω ≤
±200PPM/°C
Ω<R≦10MΩ ≤
±100PPM/°C
External Visual
No Mechanical Damage
Physical
Dimension
Reference 2.0 Dimension
Standards
Resistance to
Solvent
Terminal Strength
High Temperature
Exposure
(Storage)
Marking Unsmeared
Not broken
Resistance change rate is
± . %+ . Ω Ma .
<
Ω
Temperature
cycling
Resistance change rate is
± . %+ . Ω Ma .
<
Ω
Moisture
Resistance
Resistance change rate is
± . %+ . Ω Ma .
T=24 hours /cycle. Unpowered.
Measurement at 24±2 hours after test
conclusion.
(MIL-STD-202 Method 106)
Appl to rate urre t for Ω
10% rated power, 85°C/85%RH, 1000H.
Measurement at 24 hours after test
conclusion.
(MIL-STD-202 Method 103)
Appl to rate urre t for Ω
Wave Form: Tolerance for half sine shock
pulse. Peak
alue is
g’s. Nor al duratio
(D) is 6.
(MIL-STD-202
Method 213)
g’s for
i .,
le ea h of
orientations.
Note: Use * PCB.
thi k se ure
points (onone) long side and 2 secure points
at corners of opposite sides. Parts mounted
ithi ’ fro a se ure poi t.
Test from 10-2000Hz.
(MIL-STD-202 Method 204)
<
Ω
Biased Humidity
Resistance change rate is
± %+ . Ω Ma
<
Ω
Mechanical Shock
±(1%+0.1Ω) max
Vibration
±(1%+0.1Ω) max
9-1773463-5 Rev G 02/2020
Dimensions in
millimetres unless
otherwise specified
Dimensions Shown for
reference purposes only.
Specifications subject to
change
For Email, phone or live chat,
go to: www.te.com/help
SMD POWER RESISTORS AEC-Q200 QUALIFIED
Performance Specification (continued)
Characteristics
Limits
Test Methods
-55°C/+155°C
Note: Number of cycles required -300,
±(1%+0.1Ω max
Maximum transfer time -20 seconds, Dwell
Thermal Shock
time -15 minutes. Air-Air.
(MIL-STD-202 Method 107)
<50mΩ
Apply to rate current for 0Ω
With the electrometer in direct contact with
the discharge tip, verify the voltage setting
at levels of
ESD
±(10%+0.1W)max
±500V,±1KV, ±2KV, ±4KV, ±8KV,
The electrometer reading shall be within
±10% for voltages from 500V to
≦800V.
(AEC-Q200-002)
For both leaded & SMD. Electrical test not
required
Magnification 50X. Conditions:
a) Method B 4hrs at 155°C dry heat, the dip
Solderability
95% coverage Min.
in bath with 245°C,5s.
b) Method B: at 215°C,5s.
c) Method D: at 260°C, 60s.
( J-STD-002)
V-0 or V-1 are acceptable. Electrical test not
No ignition of the tissue paper or
Flammability
required.
scorching of the pinewood board
(UL-94)
±(1%+0.05W)max
2mm (Min)
(JIS-C-6429)
Board Flex
<50mW
Apply to rate current for 0 W
Temperature sensing at 500, Voltage
power subjected to 32VDC current clamped
Flame Retardance
No flame
up to 500ADC and decreased in
1.0VDC/hour.
( AEC-Q200-001)
Condition B No per-heat of samples. Note:
Single Wave Solder-Procedure 2 for SMD
and Procedure 1 for Leaded with solder
± %+ . Ω a .
Resistance to
within 1.5mm of device body.
soldering Heat
(MIL-STD-202 Method 210)
<50mW
Apply to rate current for 0 W
* Sulfuration test: H2S 3~5PPM 50°C±2°C 91%~93%RH 1000H
Packaging specification
Embossed Taping:
A
±0.2
3.50
B
±0.2
6.70
C
±0.05
2.0
ØD+0.1
-0
1.5
ØD1+0.1
-0
1.5
E
±0.1
1.75
F
±0.05
5.5
G
±0.1
4.0
W
±0.2
12.0
T±
0.1
1.0
9-1773463-5 Rev G 02/2020
Dimensions in
millimetres unless
otherwise specified
Dimensions Shown for
reference purposes only.
Specifications subject to
change
For Email, phone or live chat,
go to: www.te.com/help
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
