Soft Termination Chip Multilayer Ceramic Capacitors for General Purpose
GRJ155R60J106ME11_ (0402, X5R:EIA, 10uF, DC6.3V)
_: packaging code
1.Scope
This product specification is applied to Soft Termination Chip Multilayer Ceramic Capacitors used for General Electronic equipment.
Reference Sheet
2.MURATA Part NO. System
(Ex.)
GRJ
15
(1)L/W
Dimensions
5
(2)T
Dimensions
R6
(3)Temperature
Characteristics
0J
(4)Rated
Voltage
106
(5)Nominal
Capacitance
M
(6)Capacitance
Tolerance
E11
(7)Murata’s Control
Code
D
(8)Packaging Code
3. Type & Dimensions
(1)-1 L
1.0±0.2
(1)-2 W
0.5±0.2
(2) T
0.5±0.2
e
0.15 to 0.35
(Unit:mm)
g
0.3 min.
4.Rated value
(3) Temperature Characteristics
(Public STD Code):X5R(EIA)
Temp. coeff
Temp. Range
or Cap. Change
(Ref.Temp.)
(4)
Rated
Voltage
(6)
(5) Nominal
Capacitance
Capacitance
Tolerance
Specifications and Test
Methods
(Operating
Temp. Range)
-15 to 15 %
-55 to 85 °C
(25 °C)
DC 6.3 V
10 uF
±20 %
-55 to 85 °C
5.Package
mark
D
J
(8) Packaging
f180mm
Reel
PAPER W8P2
f330mm
Reel
PAPER W8P2
Packaging Unit
10000 pcs./Reel
40000 pcs./Reel
Product specifications in this catalog are as of Apr.3,2018,and are subject to change or obsolescence without notice.
Please consult the approval sheet before ordering.
Please read rating and !Cautions first.
GRJ155R60J106ME11-01
1
■
Specifications and Test Methods (Only for mobile devices)
No
1
Item
Rated Voltage
Shown in Rated value.
Specification
Test Method
(Ref. Standard:JIS C 5101, IEC60384）
The rated voltage is defined as the maximum voltage
which may be applied continuously to the capacitor.
When AC voltage is superimposed on DC voltage,
V
P-P
or V
O-P
, whichever is larger, should be maintained
within the rated voltage range.
2
3
4
Appearance
Dimension
Voltage proof
No defects or abnormalities.
Within the specified dimensions.
No defects or abnormalities.
Visual inspection.
Using Measuring instrument of dimension.
Measurement Point :
Test Voltage
:
Applied Time
:
Between the terminations
250% of the rated voltage
1 to 5 s
Charge/discharge current : 50mA max.
5
Insulation Resistance(I.R.)
More than 2000MΩ or 50Ω ∙ F (Whichever is smaller)
Measurement Point
:
Measurement Voltage :
Charging Time
:
Between the terminations
DC Rated Voltage
1 min
Charge/discharge current : 50mA max.
Measurement Temperature: Room Temperature
6
7
Capacitance
Dissipation Factor (D.F.)
Shown in Rated value.
B1,R1,B3,R6,R7,C6,C7,C8,D7 : 0.1 max.
D8
:
0.15 max
Measurement Temperature: Room Temperature
Capacitance
C≦10μF
(10V min.)
C≦10μF
(6.3V max.)
C＞10μF
Frequency
1.0+/-0.1kHz
1.0+/-0.1kHz
120+/-24Hz
Voltage
1.0+/-0.2Vrms
0.5+/-0.1Vrms
0.5+/-0.1Vrms
8
Temperature
Characteristics
of Capacitance
No bias
B1,B3 : Within +/-10%
R1,R7 : Within +/-15%
R6
C6
C7
C8
D7
D8
: Within +/-15%
: Within +/-22%
: Within+/-22%
: Within +/-22%
: Within +22/-33%
: Within +22/-33%
(-25°C to +85°C)
(-55°C to +125°C)
(-55°C to +85°C)
(-55°C to +85°C)
(-55°C to +125°C)
(-55°C to +105°C)
(-55°C to +125°C)
(-55°C to +105°C)
The capacitance change should be measured after 5 min.
at each specified temp. stage.
In case of applying voltage, the capacitance change should be
measured after 1 min. with applying voltage in equilibration of
each temp. stage.
Capacitance value as a reference is the value in step 3.
· Measurement Voltage : Less than 1.0Vrms
(Refer to the individual data sheet)
Step
1
2
Temperature(C)
Reference Temp.+/-2
Min.Operating Temp. +/-3
Reference Temp.+/-2
Max.Operating Temp. +/-3
Reference Temp.+/-2
Min.Operating Temp. +/-3
Reference Temp.+/-2
Max.Operating Temp.+/-3
50% of
the rated voltage
(For B1,R1)
Applying Voltage(VDC)
50% of
the rated
voltage
B1: Within +10/-30%
R1: Within +15/-40%
(-25°C to +85°C)
(-55°C to +125°C)
3
4
5
6
7
8
No bias
½Initial
measurement
Perform a heat treatment at 150+0/-10°C for 1h and then
let sit for 24+/-2h at room temperature,then measure.
9
Adhesive Strength
of Termination
No removal of the terminations or other defect
should occur.
GRJ03
GRJ15/GRJ18
GRJ21/GRJ31/GRJ32
Solder the capacitor on the test substrate shown in Fig.3.
Type
Applied Force(N)
2
5
10
Holding Time
:
10+/-1s
Applied Direction : In parallel with the test substrate and vertical with the
capacitor side.
10 Vibration
Appearance
Capacitance
D.F.
No defects or abnormalities.
Within the specified initial value.
Total amplitude
Within the specified initial value.
:
Solder the capacitor on the test substrate shown in Fig.3.
Kind of Vibration
:
A simple harmonic motion
10Hz to 55Hz to 10Hz (1min)
1.5mm
This motion should be applied for a period of 2h in each 3 mutually
perpendicular directions(total of 6h).
JEMCGS-05913
2
No
11 Substrate
Bending test
Item
Appearance
Specification
No defects or abnormalities.
Test Method
(Ref. Standard:JIS C 5101, IEC60384）
Solder the capacitor on the test substrate shown in Fig.1.
Pressurization method :
Flexure
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Shown in Fig.2
3mm(GRJ18/21/31/32)
5mm(GRJ03/15)
Holding Time
Soldering Method
5+/-1s
Reflow soldering
Solder bath method
Solution of rosin ethanol 25(mass)%
80℃ to 120℃ for 10s to 30s
Sn-3.0Ag-0.5Cu
245+/-5℃
2+/-0.5s
Solder bath method
Sn-3.0Ag-0.5Cu
270+/-5℃
10+/-0.5s
24+/-2h
GRJ31 size max.: 120℃ to 150℃ for 1 min
GRJ32 size : 100℃ to 120℃ for 1 min
and 170℃ to 200℃ for 1 min
· Initial measurement
Perform a heat treatment at 150+0/-10°C for 1h and then
let sit for 24+/-2h at room temperature,then measure.
Capacitance
Change
Within +/-10%
12 Solderability
95% of the terminations is to be soldered evenly and
continuously.
Test Method
Flux
Preheat
Solder
Solder Temp.
Immersion time
13 Resistance
to
Soldering
Heat
Appearance
Capacitance
Change
D.F.
I.R.
No defects or abnormalities.
Within +/-7.5%
Test Method
Solder
Solder Temp.
Immersion time
Exposure Time
Within the specified initial value.
Within the specified initial value.
Preheat
Voltage proof No defects.
14 Temperature
Sudden Change
Appearance
No defects or abnormalities.
Solder the capacitor on the test substrate shown in Fig.3.
Perform the 100 cycles according to the four heat treatments
shown in the following table.
Capacitance
Change
Within +/-7.5%
Step
1
Temp.(C)
Min.Operating Temp.+0/-3
Room Temp
Max.Operating Temp.+3/-0
Room Temp
Time
(min)
30+/-3
2 to 3
30+/-3
2 to 3
2
D.F.
Within the specified initial value.
3
4
I.R.
Within the specified initial value.
Exposure Time
· Initial measurement
:
24+/-2h
Voltage proof No defects.
Perform a heat treatment at 150+0/-10°C for 1h and then
let sit for 24+/-2h at room temperature,then measure.
15
High
Temperature
High
Humidity
(Steady)
Appearance
No defects or abnormalities.
Solder the capacitor on the test substrate shown in Fig.3.
Test Temperature
Test Humidity
:
:
:
:
40+/-2℃
90%RH to 95%RH
500+/-12h
DC Rated Voltage
Capacitance
Change
D.F.
Within +/-12.5%
Test Time
Test Voltage
Charge/discharge current : 50mA max.
0.2 max.
· Initial measurement
Perform a heat treatment at 150+0/-10°C for 1h and then
I.R.
More than 5Ω
∙
F
let sit for 24+/-2h at room temperature,then measure.
· Measurement after test
Perform a heat treatment at 150+0/-10°C for 1h and then
let sit for 24+/-2h at room temperature,then measure.
16 Durability
Appearance
No defects or abnormalities.
Solder the capacitor on the test substrate shown in Fig.3.
Test Temperature
:
:
:
Max. Operating Temp. +/-3℃
1000+/-12h
100% of the rated voltage
Capacitance
Change
Within +/-12.5%
Test Time
Test Voltage
Charge/discharge current : 50mA max.
D.F.
0.2 max.
· Initial measurement
Perform a heat treatment at 150+0/-10°C for 1h and then
let sit for 24+/-2h at room temperature,then measure.
· Measurement after test
I.R.
More than 5Ω
∙
F
Perform a heat treatment at 150+0/-10°C for 1h and then
let sit for 24+/-2h at room temperature,then measure.
JEMCGS-05913
3
Derating conditions on Voltage and Temperature (for Rated Voltage 100Vdc max.)
Derated products*1 are suitable for use in circuits w here continuous
applied voltage and temperature to the capacitor is derated (below
rated voltage and temperature).
A reliability assurance level equivalent to standard products*2 can be
secured by restricting the voltage and temperature according to the
derating conditions in the chart.
*1 Derated Products: The test voltage of these products is less than
150% of the rated voltage in the Durability / Operational Life Test.
*2 Standard Products: The test voltage of these products is 150% of
the rated voltage and over in the Durability / Operational Life Test.
Useful Lifetime for mobile application specific MLCC
100
at rated voltage x 80%
These MLCC products are designed for use in devices w ith a typical lifetime of less than 5 years.
(Examples: Cellular phone, Smartphone, Tablet PC, Digital camera, Watch, Electronics dictionary,
Small-scale server, IPC-9592B class1 equipment, etc.)
These MLCC products are designed so that the useful lifetime can be extended longer than 5 years
under the follow ing conditions:
「80%
of the rated voltage or less, Maximum operating temperature -20 degree C or less
」
Extended useful lifetime, under specific operating conditions, can be estimated from
the chart on the left.
Useful Lifetime [Year]
10
1
105℃ Type
85℃ Type
0.1
40
50
60
70
80
90
100 110 120 130
※The
useful lifetime is the time w hen cumulative failure rate becomes 1%.
※Please
note that the useful lifetime data is for reference only and not guaranteed.
Product Temperture [℃]
JEMCGS-05913
4
Test method : Substrate Bending test
・Test
substrate
Material
: Copper-clad laminated sheets for PCBs
(Glass fabric base, epoxy resin)
Thickness : 1.6mm (GRJ03/GRJ15: t:0.8mm)
Copper foil thickness : 0.035mm
: Solder resist
(Coat with heat resistant resin for solder)
*1,2：2.0±0.05
Land
f4.5
4.0±0.1
＊1
Type
GRJ03
GRJ15
GRJ18
GRJ21
GRJ31
GRJ32
a
100
a
0.3
0.4
1.0
1.2
2.2
2.2
Dimension (mm)
φ1.5
+0.1
-0
b
0.9
1.5
Ａ
3.0
4.0
5.0
5.0
Ｂ
＊2
c
0.3
0.5
1.2
1.65
0.05以下
2.0
2.9
3.5±0.05
40
c
c
1.75±0.1
8.0±0.3
b
t
Fig.1
(in mm)
・Kind
of Solder : Sn-3.0Ag-0.5Cu
・Pressurization
method
20
50 min.
Pressurization
speed
1.0mm/s
Capacitor
R5
Pressurize
45
Support
Capacitance meter
45
45
Flexure
Fig.2
(in mm)
Adhesive Strength of Termination, Vibration, Temperature Sudden Change , High Temperature High Humidity(Steady) , Durability
・Test
substrate
Material
: Copper-clad laminated sheets for PCBs
(Glass fabric base, epoxy resin)
Thickness : 1.6mm or 0.8mm
Copper foil thickness : 0.035mm
・
Kind of Solder : Sn-3.0Ag-0.5Cu
・
Land Dimensions
Chip Capacitor
Land
Type
GRJ03
GRJ15
GRJ18
GRJ21
GRJ31
GRJ32
b
a
Solder Resist
a
0.3
0.4
1.0
1.2
2.2
2.2
Dimension (mm)
b
0.9
1.5
3.0
4.0
5.0
5.0
c
0.3
0.5
1.2
1.65
2.0
2.9
c
Fig.3
JEMCGS-05913
5
下载中心专版
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
