885128
®
2.4 GHz WLAN/BT LTE Co-Existence Filter
General Description
The 885128 is a high-performance, high power Bulk
Acoustic Wave (BAW) band-pass filter with extremely
steep skirts, simultaneously exhibiting low loss in the WiFi
band and high near-in rejection in the approximate LTE
bands.
885128 is specifically designed to enable coexistence of
WiFi and LTE signals within the same device or in close
proximity to one another.
The 885128 uses common module packaging techniques
to achieve the industry leading size 1.1 x 0.9 x 0.50 mm
footprint. The filter exhibits excellent power handling
capabilities.
1.1 X 0.9 X 0.50 mm
Product Features
•
Low Loss in WLAN band with extended upper corner for
inclusion of Bluetooth
•
High Rejection in B30/B38/B7/B41 bands
•
Industry leading small size: 1.1 x 0.9 x 0.5 mm
•
Performance over −40 to +95 ºC
•
Single Ended operation
•
RoHS compliant, Pb-free module package
Functional Block Diagram
Gnd
Output
5
Input
1
2
4
3
Gnd
Applications
•
WiFi bandpass filter that enables the coexistence of
(LTE/TD-LTE) & Wi-Fi
•
Portable Hotspots
•
Wi-Fi Routers and LTE Gateways
•
Smart Meters
•
Wi-Fi Access Points
•
Small Cells
Gnd
Top View
Pin Configuration - Single Ended
Pin No.
1
4
2,3,5
Label
Input
Output
Function label
Note:
1. Pin 1 must be used for input. The large signal
performance of this filter (power handling and nonlinear
response) is not symmetric
Ordering Information
Part No.
885128
885128-EVB
Description
Packaged Part
Evaluation board
Standard T/R size = 15,000 units/reel
Advanced Data Sheet: REV F October 2018
Subject to change without notice
-
1 of 8
-
www.qorvo.com
885128
®
2.4 GHz WLAN/BT LTE Co-Existence Filter
Absolute Maximum Ratings
(1)
Parameter
Storage Temperature
Operating Temperature
RF Input Power
(2)
Rating
-40°C to 125°C
-40°C to +105°C
+36 dBm
Notes:
1. Operation of this device outside the parameter ranges given may
cause permanent damage.
2. Max CW signal applied for up to 500ms with no damage.
Pin 1 must be used for input. The large signal performance of this
filter (power handling and nonlinear response) is not symmetric.
Electrical Specifications
(1)
Test conditions unless otherwise noted:
(2)
−30 °C to +85 °C
Parameter
(3)
Conditions
2402.5 – 2421.5 MHz (WiFi Ch.1)
2407.5 – 2426.5 MHz (WiFi Ch.2)
2412.5 – 2471.5 MHz (WiFi Ch.3-11)
2412.5 – 2471.5 MHz (WiFi Ch.3-11)(19 MHz sliding window)
2457.5 – 2476.5 MHz (WiFi Ch.12)
2462.5 – 2481.5 MHz (WiFi Ch.13)
Min Typ
(5)
Max Units
-
-
-
-
-
-
-
-
-
-
32
32
42
33
31
23
44
41
47
45
27
27
-
-
-
-
1.5
1.3
1.1
1.3
1.3
1.5
0.9
0.7
0.7
0.5
0.9
33
33
47
39
38
38
50
50
50
49
33
31
1.6
24
50
50
1.7
1.5
1.4
1.5
1.6
1.9
1.4
0.9
1.1
1.2
2.0
-
-
-
-
-
-
-
-
-
-
-
-
2.0
-
-
-
Insertion Loss
(6)
dB
2402.5 – 2421.5 MHz (WiFi Ch.1)
2407.5 – 2426.5 MHz (WiFi Ch.2)
Amplitude Variation
2412.5 – 2471.5 MHz (WiFi Ch.3-11)
2457.5 – 2476.5 MHz (WiFi Ch.12)
2462.5 – 2481.5 MHz (WiFi Ch.13)
925 – 960 MHz
1559 – 1606 MHz
2110 – 2170 MHz
2300 – 2370 MHz
(7)
2500 – 2505 MHz (+25 to +85˚C)
(7)
2500 – 2505 MHz (−30 to +25˚C)
(7)
Rejection
2505 – 2570 MHz (+25 to +85˚C)
(7)
2505 – 2570 MHz (−30 to +25˚C)
(7)
2570 – 2620 MHz
(7)
2620 – 2690 MHz
(7)
4800 – 5000 MHz
7200 – 7500 MHz
Input /Output VSWR 2402.5 – 2481.5 MHz
RF Input Power
(8)
2400 – 2483 MHz
Source Impedance
(9)
(single-ended)
Load Impedance
(9)
(single-ended)
dB p-p
dB
-
dBm
Ω
Ω
Notes:
1. All specifications are based on the Qorvo schematic shown on page 5.
2. In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over
temperature.
3. Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances.
4. An external impedance matching network with ±2 % tolerance will be necessary to achieve the stated specifications.
5. Typical values are based on average measurements at room temperature.
6. Data is the integrated value of the linear s-parameter over a 19 MHz range in the indicated band at the specified temperature.
7. Data is the integrated value of the linear s-parameter over 5MHz range at the specified temperature.
8. Input power applied for a minimum of 5,000 hrs. at 55 °C in the frequency band specified.
9. This is the optimum impedance in order to achieve the performance shown.
Advanced Data Sheet: REV F October 2018
Subject to change without notice
-
2 of 8
-
www.qorvo.com
885128
®
2.4 GHz WLAN/BT LTE Co-Existence Filter
Electrical Specifications
(1)
Test conditions unless otherwise noted:
(2)
−40 °C to +95 °C
Parameter
(3)
Conditions
2402.5 – 2421.5 MHz (WiFi Ch.1)
2407.5 – 2426.5 MHz (WiFi Ch.2)
2412.5 – 2471.5 MHz (WiFi Ch.3-11)
2412.5 – 2471.5 MHz (WiFi Ch.3-11)(19 MHz sliding window)
2457.5 – 2476.5 MHz (WiFi Ch.12)
2462.5 – 2481.5 MHz (WiFi Ch.13)
2402.5 – 2421.5 MHz (WiFi Ch.1)
2407.5 – 2426.5 MHz (WiFi Ch.2)
2412.5 – 2471.5 MHz (WiFi Ch.3-11)
2457.5 – 2476.5 MHz (WiFi Ch.12)
2462.5 – 2481.5 MHz (WiFi Ch.13)
925 – 960 MHz
1559 – 1606 MHz
2110 – 2170 MHz
2300 – 2370 MHz
(7)
2500 – 2505 MHz (+25 to +95˚C)
(7)
2500 – 2505 MHz (−40 to +25˚C)
(7)
2505 – 2570 MHz (+25 to +95˚C)
(7)
2505 – 2570 MHz (−40 to +25˚C)
(7)
2570 – 2620 MHz
(7)
2620 – 2690 MHz
(7)
4800 – 5000 MHz
7200 – 7500 MHz
2402.5 – 2481.5 MHz
2400 – 2483 MHz
(single-ended)
(single-ended)
Min Typ
(5)
Max Units
-
-
-
-
-
-
-
-
-
-
32
32
42
33
31
22
44
39
47
45
27
27
-
-
-
-
1.5
1.3
1.1
1.3
1.3
1.5
0.9
0.7
0.7
0.5
0.9
33
33
47
39
38
38
50
50
50
49
33
31
1.6
24
50
50
1.7
1.5
1.3
1.6
1.7
2.0
1.5
0.9
1.1
1.2
2.1
-
-
-
-
-
-
-
-
-
-
-
-
2.0
-
-
-
Insertion Loss
(6)
dB
Amplitude Variation
dB p-p
Rejection
dB
Input /Output VSWR
RF Input Power
(8)
Source Impedance
(9)
Load Impedance
(9)
-
dBm
Ω
Ω
Notes:
1. All specifications are based on the Qorvo schematic shown on page 5.
2. In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over
temperature.
3. Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances.
4. An external impedance matching network with ±2 % tolerance will be necessary to achieve the stated specifications.
5. Typical values are based on average measurements at room temperature.
6. Data is the integrated value of the linear s-parameter over a 19 MHz range in the indicated band at the specified temperature.
7. Data is the integrated value of the linear s-parameter over 5MHz range at the specified temperature.
8. Input power applied for a minimum of 5,000 hrs. at 55 °C in the frequency band specified.
9. This is the optimum impedance in order to achieve the performance shown.
Advanced Data Sheet: REV F October 2018
Subject to change without notice
-
3 of 8
-
www.qorvo.com
885128
®
2.4 GHz WLAN/BT LTE Co-Existence Filter
Electrical Specifications
(1)
Test conditions unless otherwise noted:
(2)
0 °C to +70 °C
Parameter
(3)
Conditions
2402.5 – 2421.5 MHz (WiFi Ch.1)
2407.5 – 2426.5 MHz (WiFi Ch.2)
2412.5 – 2471.5 MHz (WiFi Ch.3-11)
2412.5 – 2471.5 MHz (WiFi Ch.3-11)(19 MHz sliding window)
2457.5 – 2476.5 MHz (WiFi Ch.12)
2462.5 – 2481.5 MHz (WiFi Ch.13)
2402.5 – 2421.5 MHz (WiFi Ch.1)
2407.5 – 2426.5 MHz (WiFi Ch.2)
2412.5 – 2471.5 MHz (WiFi Ch.3-11)
2457.5 – 2476.5 MHz (WiFi Ch.12)
2462.5 – 2481.5 MHz (WiFi Ch.13)
925 – 960 MHz
1559 – 1606 MHz
2110 – 2170 MHz
2300 – 2370 MHz
(7)
2500 – 2505 MHz (+25 to +70˚C)
(7)
2500 – 2505 MHz ( 0 to +25˚C)
(7)
2505 – 2570 MHz (+25 to +70˚C)
(7)
2505 – 2570 MHz ( 0 to +25˚C)
(7)
2570 – 2620 MHz
(7)
2620 – 2690 MHz
(7)
4800 – 5000 MHz
7200 – 7500 MHz
2402.5 – 2481.5 MHz
2400 – 2483 MHz
(single-ended)
(single-ended)
Min Typ
(5)
Max Units
-
-
-
-
-
-
-
-
-
-
-
32
32
43
33
31
26
44
44
47
46
27
27
-
-
-
-
1.5
1.3
1.1
1.3
1.3
1.5
0.9
0.7
0.7
0.5
0.9
33
33
47
39
38
38
50
50
50
49
33
31
1.6
24
50
50
1.6
1.3
1.2
1.3
1.6
1.7
1.2
0.9
0.9
0.9
1.6
-
-
-
-
-
-
-
-
-
-
-
-
1.9
-
-
-
Insertion Loss
(6)
dB
Amplitude Variation
dB p-p
Rejection
dB
Input /Output VSWR
RF Input Power
(8)
Source Impedance
(9)
Load Impedance
(9)
-
dBm
Ω
Ω
Notes:
1. All specifications are based on the Qorvo schematic shown on page 5.
2. In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over
temperature.
3. Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances.
4. An external impedance matching network with ±2 % tolerance will be necessary to achieve the stated specifications.
5. Typical values are based on average measurements at room temperature.
6. Data is the integrated value of the linear s-parameter over a 19 MHz range in the indicated band at the specified temperature.
7. Data is the integrated value of the linear s-parameter over 5MHz range at the specified temperature.
8. Input power applied for a minimum of 5,000 hrs. at 55 °C in the frequency band specified.
9. This is the optimum impedance in order to achieve the performance shown.
Advanced Data Sheet: REV F October 2018
Subject to change without notice
-
4 of 8
-
www.qorvo.com
885128
®
2.4 GHz WLAN/BT LTE Co-Existence Filter
Evaluation Board – 885128-EVB
Notes:
1. Matching component values shown are for the specified TriQuint evaluation board. Value adjustment may be required in end user product circuits
depending on component manufacturer and PCB material.
2. PCB: .500 x.500 x .062; Construction: ½ oz
Cu
Top Layer;
TLY-5A
(.0075) ½ oz
Cu
Middle Layer,
FR4;
½ oz
Cu
Bottom Layer. (dimensions are in
inches)
Bill of Material – 885128-EVB
Reference Des.
U1
L1
L2
SMA
PCB
Value
N/A
10 nH
10 nH
N/A
N/A
Description
2.4 GHz WLAN/BT filter
Chip Inductor, 0201, ± 2 %
Chip Inductor, 0201, ± 2 %
SMA connector
3 Layer
Manuf.
Qorvo
Murata
Murata
Radiall
Multiple
Part Number
885128
LQP03TH10NH02D
LQP03TH10NH02D
9602-1111-018
961094-04
PCB Mounting Pattern
0.975
3X
0.18
Notes:
1. All dimensions are in millimeters. Angles are in degrees.
2. This drawing specifies the mounting pattern used on the Qorvo evaluation
board for this product. Some modification may be necessary to suit end user
assembly materials and processes.
2X 0.225
0.775
5X 0.275
5X
0.205
Advanced Data Sheet: REV F October 2018
Subject to change without notice
-
5 of 8
-
www.qorvo.com
模拟电子
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
