Cannon VG/CA-Bayonet
Introduction
Connector Design
Due to the rugged shell made of an aluminium alloy, these
connectors withstand most severe conditions. Olive drab
chromate coating over cadmium plating protects the surface of
the shell.
Cannon offers two plating solutions to customers refusing
cadmium plating. Zinc cobalt green offers similar properties like
cadmium plating while zinc cobalt black is RoHS compliant.
Over 180 contact arrangements are available for 1 to 65 circuits
and up to 245 A per unit.
The insulators are made of high quality polychloroprene and
withstand temperatures from -67°/+257°F (-55/125°C). This
material is self-extinguishing, resistant against hydraulic fluids,
jet fuel, diesel fuel, gasolines, lubricants, brake and fire
extinguisher fluids (short wetting only). In case of lifetime
moistening ITT Cannon offers FKM insulators as an alternative.
The contacts are made of copper alloy plated with a hard silver
finish guarantee at least 500 mating cycles. There are solder,
crimp and PCB contacts in place. The crimp contacts offer a
comprehensive range of termination reductions. All solder
contacts feature a special passivation to comply with ROHS
requirements. The crimp contacts allow highly reliable crimping
with wires when using the recommended tools according to
VG95234. Crimp contacts can be exchanged at least five times
still preserving specified contact retention.
The coupling unit is featured by the Cannon roller bolts made
of stainless steel actually rolling down the mating ramps, thus
reducing coupling force by the operator. In addition, the
Cannon design employs two coupling nut versions for different
application cases, with and without wavespring and washer.
The version without wavespring guarantees perfect sealing
while the other version stands up to high vibration levels.
The bayonet design allows fast and easy coupling and
uncoupling. An audible control by metallic sound and
visual control by colour-marked snap-in position offer
additional coupling security.
VG connectors are basically designed for single wire harnessing.
For full environmental sealing each conductor is sealed com-
pletely within the grommet. However, Cannon offers as an
alternative O-ring sealed PG and
metric gland adaptors for faster
harnessing standing up to the same
sealing level than the VG types.
A
Cannon CA-Bayonet series was designed in accordance with
the VG95234 specification. This versatile and highly reliable
connector series is an improvement on the well established
MIL-C-5015 series. CA-Bayonet has a proven “reverse bayonet”
coupling design that offers exceptional vibration protection, by a
simple 120° turn.
Initially designed for aircraft and airborne applications, these
rugged connectors are used in the electrical equipment of vari-
ous off-road vehicles, construction machinery, industrial devices,
railroad and military wheelers.
Connectors in accordance with VG95234 are interchangeable
with the corresponding MIL-C-5015 connectors. Both connector
lines feature the same shell dimensions and contacts layouts.
However, due to the different coupling systems (MIL-C-5015
threaded coupling, VG95234 bayonet coupling) they are not
intermateable.
Circular
Advantages
– rugged shell design
– environmental
– bayonet coupling for easy mating and unmating
– vibration proof
– waterproof up to 1 bar (35 feet of water)
Cannon has the complete VG95234 program available and, in ad-
dition, many other types which exceed the requirements of
VG95234 and MIL-C-5015.
Attention:
Metal shell connectors which may be touched are not
suitable for mains power.
Restrictions:
* European Community “Old Car” directive (2000/53/EG)
* European Community Waste Electrical and Electronic Equipment (WEEE)
2000/0158
* European Community restrictions of use of certain hazardous substances
in WEEE (ROS) (2000/0159)
Dimensions shown in inches (mm)
Specifications and dimensions subject to change
A-130
www.ittcannon.com
Cannon VG/CA-Bayonet
Electrical Data
Contact rating at 68 °F (+20 °C)
Contact size
10
16S/15S
16/15
12/25
8/60/100
4/160
0/500
Current rating
depending on ambient temperature
Derating Curves according to VG 95234
250
240
230
220
210
200
190
180
170
160
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
20
30
40
50
60
70
80
90
100
110
Contact resistance
(Millivolt test)
max. current
A
8
22
22
41
74
135
245
The contact resistance has to be tested according to VG95234
part 2, test no. 5.10.1 and VG 95210, part 37. The measuring
points are indicated in the illustration.
--Contact size
metric
10
15S/15
25
60/100
160
500
AWG
–
16S/16
12
8
4
0
Max. contact
resistance
mΩ
12
6
3
1
0,5
0,2
A
Circular
Contact
size
500/ 0,
wire size
50mm²/ AWG0
Contact
size
160/ 4;
wire size
16mm²/ AWG4
Contact
size
60/ 100/ 8;
wire size
60/ 100mm²/
AWG8
Contact
size
25/ 12;
wire size
2,5mm²/ AWG12
Contact
size
15/ 15s/ 16/ 16s;
wire size
1,5mm²/
AWG16
Contact
size
10/ 20;
wire size
0,75/ 1,0mm²
Current [A]
Insulation resistance
Acc. to VG95319, part 2, test no. 5.12 and VG95210, part 32,
test condition B
Standard insulator material
> 1000 MΩ
FKM insulator material (upon request)
> 5000 MΩ
Test voltage
Acc. to VG95319, part 2, test no. 5.13 and VG 95210, part 31
Test voltage for service rating:
Service rating
Instruments
A
B
D
E
Air and creepage paths
(min.)
Test voltage Vrms
1050
1600
4000
2500
3000
120
130
Ambient Temperature [°C]
Derating Curves ITT-Cannon
330
320
310
300
290
280
270
260
250
240
230
220
210
200
190
180
170
160
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
20
30
40
50
60
70
80
90
100
110
120
Voltage class
Contact
size
500;
wire size
50mm²
Contact
size
160,
wire size
16mm²
Contact
size
100;
wire size
10mm²
Contact
size
60;
wire size
6mm²
Instr.
0,7
A
1,1
D
2,8
E
4,8
Air and creepage paths mm
Operating voltage and connector usage
Connectors in equipments must not be separated or mated
under load when used per specifications.
As according to specification the connectors are suitable for an
operating voltage of 50 V (see Product Safety Information).
However, this is only valid, when the connectors are freely
accessible during operation and consequently might be
touchable. When the connectors will be operated with line
voltage, please contact ITT Customer Service for an alternative
connector solution.
Current [A]
130
Ambient Temperature [°C]
Dimensions shown in inches (mm)
Specifications and dimensions subject to change
www.ittcannon.com
A-131
Cannon VG/CA-Bayonet
Mechanical Features
Ambient temperature
Standard insulator material
–55°/125°C (– 67/257°F)
FKM insulator material*
–30°/200°C (– 22/392°F)
Safety provisions**
IP 67 acc. to DIN 40 050
(1 bar pressure after 16 hrs.)
Vibration test
200 m/s2 at 10 to 2000 Hz
Mating cycles
500 min.
Withdrawal force
per contact.
The corresponding withdrawal force has to be measured
according to VG95319, part 2, test no. 5.7. and
DIN EN60512-16-5 using the required test gage.
Contact size
metric
10
15S/15
25
60/100
160
500
Separating force min.
N
Gage
0,3
G 0,99
1,0
G 1,56
1,5
G 2,36
3,0
G 3,58
4,0
G 5,69
8,5
G 9,04
Coupling torque
The allowable coupling torques have to be tested under full
bundle conditions of the connectors to VG95319, part 2, test no.
5.8.2.
Shell
size
10SL
12S
14S
16S/16
18
20
22
24
28
32
36
Allowable coupling torque
closing and opening
Nm max.
1,7
2,5
3,6
5,5
8
9
11
14
17
19
23
A
Circular
Opening
Nm min.
0,15
0,23
0,35
0,46
0,58
0,7
0,8
0,8
0,92
1,03
1,03
AWG
–
16S/16
12
8
4
0
Contact retention
The contact retention has to be tested according to VG95319,
part 2, test no. 5.4. Test force direction = Mating direction.
Contact
size
10
15S/15
25
60/100
160
500
AWG
–
16S/16
12
8
4
0
Test force
N
30
35
55
80
90
95
Gage
(see also VG 95234, Part 1)
Materials
Shell
Standard finish
Alternative finish
Gage
G 0,99
G 1,56
G 2,36
G 3,58
G 5,69
G 9,04
Contact diameter d
+0,01
0,99
1,56
2,36
3,58
5,69
9,04
L
–1
7
9
12
13
13
13
Insulator
and grommets
Contacts
Standard finish
Special finish
**
upon request
**
Longitudinal sealing:
The connector is not sealed against fluids entering
through the cable, as the sealing lips of the single wire sealing are pressing
against the jacket of the individual conductors.
Aluminum alloy
Olive drab chromate coating over
cadmium plating
Zinc cobalt (see page A-134
Modification)
Polychloroprene (Standard)
FKM (High temperature and
aggressive oils)*
Copper alloy
Hard silver
A176 nickel and hard gold plating
Dimensions shown in inches (mm)
Specifications and dimensions subject to change
A-132
www.ittcannon.com
Cannon VG/CA-Bayonet
How to order
VG Order reference
VG 95234 A
Series
Shell style
Dash
Shell size
Contact arrangement
Contact type
Contact termination
Insulator position
–
32 – 6
S
1 N
Series
Cannon Order reference
CA 3106 E 18 – 1
S
X
B
– ***
A
Circular
Shell style
Class
Shell size
Contact arrangement
Contact type
Insulator position
Connectors with bayonet coupling
Dash
VG 95234
N1, N2 – wall mounting receptacle
A, B1, B2 – box mounting receptacle
D, G, H, M – straight plug
10SL, 14S, 16S, 16, 18, 20, 22,
24, 28, 32 and 36
see pages A-135 and A-136
P – Pin contact
S – Socket contact
without identification –
contacts for metric wire sizes
identification 1* –
contact for AWG wire sizes
See CA-Bayonet Catalog
Modification
Explanation
Series
Shell style
Explanation
Series
Shell style
CA
– Circular connectors with bayonet
coupling
Waåll mounting receptacle
Cable connecting plug
Box mounting receptacle
Dummy receptacle for front and
panel mounting
3106 – Plug, straight
3108 – Plug, 90°
TBF – Bulkhead receptacle
– environmental with resilient
insulators and endbell with clamp
and bushing
F
– environmental with resilient
insulator and endbell for flex tube
R
– environmental with resilient
insulator and shortened light-weight
endbell without cable clamp
10SL, 12S, 14S, 16S, 16, 18, 20,
22, 24, 28, 32 and 36
See 5015 section plus full CA-B catalog
P
S
PS
– Pin
– Socket
– one side pin, one side socket
(only for TBF)
E
3100 –
3101 –
3102 –
3105 –
Shell size
Contact arrangement
Contact type
Contact termination
Class
Insulator position
Accessories acc. to VG
Dummy receptacles
Gaskets, front mount
Gaskets, rear mount
Protecting caps
Protecting caps
Cabel caps
Bushing
VG95234 BOD
VG95234 DA
VG95234 DH
VG95234 KR
VG95234 KB
VG95234 KK
VG95234 KT
Shell size
Contact
arrangement
Contact type
Insulator position
Besides the normal position further insulator
positions are possible for Cannon connectors
(see CA-Bayonet Catalog) to prevent mismat-
ing. Polarization is achieved by turning the pin
contact insulator clockwise towards the shell,
the socket insulator, however, in opposite
clockwise direction. This information refers to
the mating side of the contact insulator.
Modification
see next page A-134
Dimensions shown in inches (mm)
Specifications and dimensions subject to change
www.ittcannon.com
A-133
模拟与混合信号
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
