SIL40C2 Series
DC-DC CONVERTERS
•
•
•
•
•
•
•
C Class Non-isolated
4.5-13.8 Vin Single Output
March 15, 2006
1
NEW Product
•
40 a current rating
Input voltage range: 4.5-13.8 V
Output voltage: 0.6-5 V
Industry leading value
•
Cost optimized design
excellent transient response
Output enable
Output voltage adjustability
•
Pathway for future upgrades
•
Supports silicon voltage migration
•
resulting in reduced design-in and qual time
roHS compliant
The SIL40C2 series is a new high density open frame non-isolated converter
for space sensitive applications. This model has a wide input range (4.5-13.8
Vdc) and offers a wide 0.6-5 V output voltage range with 40 A load capability.
An external resistor adjusts the output voltage from its pre-set value of 0.6 V to
any value up to the 5 V maximum. Typical efficiencies for the models are 91%
for the 12 V input version. The SIL40C2 series offers remote ON/OFF and
over-current protection as standard.
2 year warranty
All specifications are typical at nominal input, full load at 25 °C unless otherwise stated
OUTPUT SPECIFICATIONS
Output voltage
Output setpoint
accuracy
Line regulation
Load regulation
Min/max load
Overshoot
Undershoot
Ripple and noise
5 Hz to 20 MHz
Transient response
At turn-on
At turn-off
(See Note 1)
(See Notes 1, 2)
(See Note 5)
0.1% trim resistors
Low line to high line
Full load to min. load
0.6-5 V
±1.0%
±0.2%
±0.5%
0 A/40 A
0.5% max.
100 mV max.
25 mV
Vin = 5 V, Vout = 2.5 V
150 mV max. deviation
30 µs recovery within
regulation band
Coplanarity
ENVIRONMENTAL SPECIFICATIONS
Thermal performance
(See Note 5)
Operating ambient,
temperature
Non-operating
0 °C to +70 °C
-40 °C to +125 °C
GENERAL SPECIFICATIONS
Efficiency
Switching frequency
Approvals and
standards (pending)
Material flammability
Weight
MTBF
12 V @ 40 °C
100% load
Bellcore 332
Vin=5 V, Vo=2.5 V, lo=20 A
Fixed
94% Typ.
500 kHz
EN60950
UL/cUL60950
UL94V-0
17 g/0.06 oz.
6,749,409 hours
SPECIFICATIONS
150 µm
INPUT SPECIFICATIONS
Input voltage range
Input current
Input current (max.)
Start-up time
Minimum load
Remote OFF
(See Note 3)
Remote ON/OFF
4.5-13.8 Vdc
50 mA
5 mA
25 A @ Io max.
3 ms
PROTECTION
Short-circuit
Over voltage
RECOMMENDED SYSTEM
CAPACITANCE
Input capacitance
(See Note 6)
(See Note 7)
0 µF
0 µF
Hiccup, non-latching
Hiccup, non-latching
International Safety Standard Approvals
UL/cUL CAN/CSA 22.2 No. E139421
UL60950 File No. TBD
TÜV Product Service (EN60950) Certificate No. TBD
CB report and certificate to IEC60950
Output capacitance
File Name: sil40c2.pdf Rev: 15 Mar 2006
SIL40C2 Series
DC-DC CONVERTERS
C Class Non-isolated
OUTPUT
POWER
(MAX.)
200 W
INPUT
VOLTAGE
4.5-13.8 Vdc
OVP
N/A
OUTPUT
VOLTAGE
0.6-5 Vdc
OUTPUT
CURRENT
(MIN.)
0A
4.5-13.8 Vin Single Output
March 15, 2006
2
NEW Product
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
OUTPUT
CURRENT
(MAX.)
40 A
EFFICIENCY
(TYP.)
94%
REGULATION
LINE
±0.2%
LOAD
MODEL
NUMBER
(8, 9)
±0.5% SIL40C2-00SADJ-VJ
Part Number System with Options
SIL40C2-00SADJ-VJ
RoHS Compliance
(8)
J = Pb-free (RoHS 6/6 compliant)
Mounting Option
V = Vertical
H = Horizontal
Output Voltage
Single Adjustable Output
Input Voltage
00 = 4.5-13.8 V
Product Family
SIL = Single In Line
SMT = Surface Mount
Rated Output Current
06 = 6 A
15 = 15 A
20 = 20 A
30 = 30 A
40 = 40 A
Performance
C = Cost Optimized
Generation
Blank = Standard Part
2 = Increased Current Density
Output Voltage Adjustment of the SIL40C2 Ser
ies
The ultra-wide output voltage trim range offers major advantages to users
who select the SIL40C2. It is no longer necessary to purchase a variety of
modules in order to cover different output voltages. The output voltage can
be trimmed in a range of 0.6-5 V. When the SIL40C2 converter leaves the
factory the ouput has been adjusted to the default voltage of 0.6 V.
Notes
1
2
3
4
5
6
7
8
9
Measured as per recommended system capacitance.
di/dt = 10 A/µs, Vin = Nom, Tc = 25 °C, load change = 0.75 lo to
full lo and full lo to 0.75.
External input fusing is recommended.
Additional part numbers may be available with different output
voltages.
Airflow dependent, 100 LFM minimum required.
No capacitor needed for ripple current capability.
No capacitor needed for stability.
TSE RoHS 5/6 (non PB-free) compliant versions are also available
on special request, please contact your local sales representative
for details.
NOTICE: Some models may not support all options. Please
contact your local Artesyn representative or use the on-line model
number search tool at http://www.artesyn.com/powergroup/
products.htm to find a suitable alternative.
Power Good
6
Enable
5
SIL40C2
V
in
1,2,3
9
V
out
+R
sense
10,11
7,8
C
in
R
trim
(for trim
down)
C
out
4
R
L
O
A
D
GND
Figure 1: Standard Application Drawing
File Name: sil40c2.pdf Rev: 15 Mar 2006
SIL40C2 Series
DC-DC CONVERTERS
C Class Non-isolated
4.5-13.8 Vin Single Output
March 15, 2006
3
NEW Product
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
1.200 (30.48)
0.427 (10.85)
1.100 (27.94)
0.050 (1.27) REF
PIN 1
0.100 (2.54)
0.100 (2.54) TYP
9 PLACES
0.140 (3.56) TYP
0.255 (6.48)
0.062 (1.57) REF
0.110 (2.79)
PIN CONNECTIONS
PIN NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
FUNCTION
Vout
Vout
Vout
Trim
Enable
Power Good
Ground
Ground
(+) Sense
Vin
Vin
*Mech Support
*Mech Support
0.468 (11.89)
0.255 (6.48)
1.050 (26.67)
Dimensions in Inches (mm)
Tolerances (unless otherwise specified)
2 Places ±0.030 (±0.76)
3 Places ±0.010 (±0.25)
0.050 (1.27) TYP
0.025 (0.64) ±.001
SQ PINS TYP
Figure 2: Vertical Mount Mechanical Drawing
1.200 (30.48)
0.062 (1.57) REF
.150 (3.81) TYP
1.100 (27.94)
PIN 1
0.110 (2.79) REF
2X
1.000 (25.40)
0.050 (1.27) REF
* Horizontal and SMT version only
0.120 (3.05) TYP
0.025 (0.64) ±.001
SQ PINS TYP
13 PLACES
0.100 (2.54) TYP
9 PLACES
Dimensions in Inches (mm)
Tolerances (unless otherwise specified)
2 Places ±0.030 (±0.76)
3 Places ±0.010 (±0.25)
2X 1.050 (26.67)
0.050 (1.27)
0.100 (2.54) REF
Figure 3: Horizontal Mount Mechanical Drawing
File Name: sil40c2.pdf Rev: 15 Mar 2006
SIL40C2 Series
DC-DC CONVERTERS
C Class Non-isolated
PIN CONNECTIONS
PIN NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
FUNCTION
Vout
Vout
Vout
Trim
Enable
Power Good
Ground
Ground
(+) Sense
Vin
Vin
*Mech Support
*Mech Support
4.5-13.8 Vin Single Output
March 15, 2006
4
NEW Product
1.200 (30.48)
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
0.442 (11.23)
0.255 (6.48)
0.110 (2.79) REF
0.062 (1.57) REF
0.125 (3.18) TYP
1.100 (27.94)
PIN 1
2X
1.000 (25.40)
0.050 (1.27) REF
0.100 (2.54) TYP
9 PLACES
Dimensions in Inches (mm)
Tolerances (unless otherwise specified)
2 Places ±0.030 (±0.76)
3 Places ±0.010 (±0.25)
2X 1.050 (26.67)
0.050 (1.27)
0.100 (2.54) REF
Figure 4: Surface Mount Mechanical Drawing
* Horizontal and SMT version only
Datasheet © Artesyn Technologies® 2005
The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications
are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein.
Please consult our website for the following items:
Application
Note
Longform
Datasheet
www.artesyn.com
File Name: sil40c2.pdf Rev: 15 Mar 2006
PCB设计
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
