P-NUCLEO-IOD01A1
Data brief
STM32 Nucleo pack for IO-Link device fully compatible with IO-Link v1.1 (PHY
and stack)
Features
•
Equipped with Arduino UNO R3 connectors and compatible with
STM32 Nucleo
boards:
–
STEVAL-IOD003V1
◦
IO-Link (PHY) device layer based on
L6362A
◦
Operating voltage range 6.5 to 35 V
◦
Dedicated CQ overload pin (wake-up)
◦
Diagnostics pin (UVLO, over-temperature and cut-off)
◦
UART interface
◦
Linear regulators for independent supply from +24 V bus (12 mA 3.3 V
and 100 mA 12 V)
◦
LEDs for status and diagnostics
◦
Overload and overheating protections with non-dissipative cut-off
function
◦
Full reverse polarity on IO-Link interface pins
◦
EMC protections according to IO-Link v1.1 and IEC 60947-5-2
◦
Ground and V
CC
wire break protections
X-NUCLEO-IKS01A2
◦
LSM6DSL 3D accelerometer and 3D gyroscope
◦
LSM303AGR 3D accelerometer and 3D magnetometer
◦
LPS22HB pressure sensor
◦
HTS221 capacitive digital relative humidity and temperature
◦
DIL24 socket for additional MEMS adapters and other sensors
◦
Free comprehensive development firmware library and samples for all
sensors compatible with STM32Cube firmware
NUCLEO-L073RZ
–
–
–
–
–
STM32L073RZT6
32-bit microcontroller based on ARM
®
Cortex
®
-M0+ core
Pre-programmed IO-Link device stack (v1.1 compatible)
Arduino UNO R3 connectivity and ST morpho extension pin headers
Mbed-enabled (http://mbed.org)
On-board ST-LINK/V2-1 debugger/programmer with SWD connector
–
Product summary
STM32 Nucleo
pack for IO-Link
(PHY) device
fully compatible
with IO-Link v1.1
(PHY and stack)
P-NUCLEO-IOD01A1
•
IO-Link device
evaluation board
based on L6362A
STEVAL-IOD003V1
with Arduino
connectors for
STM32 Nucleo
IO-Link
communication
transceiver
device IC
Description
L6362A
Motion MEMS
and
environmental
X-NUCLEO-IKS01A2
sensor expansion
board for STM32
Nucleo
The
P-NUCLEO-IOD01A1
is an
STM32 Nucleo
pack composed of the
NUCLEO-
L073RZ
development board, the
STEVAL-IOD003V1
evaluation board and the
X-
NUCLEO-IKS01A2
expansion board.
The STEVAL-IOD003V1 offers an IO-Link device PHY layer (L6362A) while the
NUCLEO-L073RZ runs an IO-Link demo stack (developed by and property of
TEConcept Gmbh) compatible with rev 1.1 and firmware controlling the X-NUCLEO-
IKS01A2 sensors.
The STM32 Nucleo pack provides an affordable and easy-to-use solution for the
development of IO-Link and SIO applications, L6362A communication features and
robustness, together with the
STM32L073RZT6
computation performance.
DB3635
-
Rev 2
-
July 2018
For further information contact your local STMicroelectronics sales office.
www.st.com
P-NUCLEO-IOD01A1
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST
products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST
products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2018 STMicroelectronics – All rights reserved
DB3635
-
Rev 2
page 4/4
模拟电子
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
