Safety mats & Area guarding
Um Series
Universal Safety mat System
UM
Rev. 5.11
heavy-Duty four-Wire Presence Sensing mats
with integrated (non-removable) cable,
category 3 controllers, and Perimeter trim
System
• When UM series mats are combined with an MC3, MC4 or MC6
controller (with complete diagnostics), the result is a system
that meets the standard EN 1760-1:1998 and is entitled to
display the CE mark. See below for an overview of the various
components.
mat
• Activation force: 30 kg (66 lb.) per ANSI/RIA 15.06-1999,
ISO 13856-1:2001, ANSI B11.19-2003, and CSA Z432-04
• Conductive plates: 24 gauge galvanealed sheet steel
• Contact yield strength in excess of 20,000 lb./sq. in.; Fork lift
traffic of 12,000 lb.
• Mat housing cross section: 13.5 mm (0.54 in.)
• PVC black or yellow covering materials (other colors available
on request)
• Durometer of 80 (±3) shore A
• Single-piece molded construction
• Mat flammability self extinguishing, meets UL94VO
• IP67 rated
• Operating temperature -37 to 66°C (-35 to 150°F)
• Mat cable: 18-gauge, 4-conductor, 16-strand, 300 VAC
• Cable length: Standard 5 m (16 ft.), Optional 10 m (32 ft.)
controllers
• Safety category 3 device
• DIN-rail mount (MC3)
• NEMA controllers (MC4, MC6)
• 24 VDC or with universal power supply 100 to 240 VAC
trim
• Two-part perimeter and joining trim simplifies installation and
provides a custom appearance
• Aluminum base surrounds mat, the safety yellow PVC cover
secures mat in place, an aluminum cover that is installed in
place of the PVC cover is also available
• Two-part active joining trim joins multiple mats together
• Molded inside and outside corners available as an option
f
r
C
US
Description
An Omron STI Universal Mat system (UM series mat combined
with an MC3, MC4 or MC6) offers a simple method for guarding
personnel around hazardous machines. A Universal Mat system
offers freedom, flexibility, and reduced operator fatigue when
compared with traditional guarding methods such as interlocked
fences, pullback restraints or perimeter barriers.
Full visibility of and access to the work area is maintained. There
is no need to worry about personnel forgetting to replace mechani-
cal barriers or close gates.
how the System Works
The operation of a Universal Mat system is easy to understand.
The mat is a simple, normally open switch. When a specified
minimum weight is applied to the mat the "switch" closes. This
sends a signal to the controller which, in turn, sends a stop signal
to the guarded machine.
Each mat presents four wires to the controller. This provides the
redundancy required to monitor the wiring for open circuits due to
incorrect wiring or physical damage to the wires.
In order to meet many national safety regulations, Omron STI
offers trim to secure the mat to the floor so that it cannot be easily
relocated and therefore become ineffective.
f2
OmrOn Scientific technOlOgieS, inc.
USA
Tel. 1/888/510-4357
canada
Tel. 1/866/986-6766
For the Latest Information
On the Internet:
www.sti.com
Um Series
Safety mats & Area guarding
Applications
Presence sensing safety mats are used to monitor an entire
hazardous area. They offer flexibility, quick access and may
frequently be the most economic choice. Other options for
perimeter guarding include interlocked barrier guards and safety
light curtains. However, personnel can become trapped inside a
barrier guard and safety light curtains only monitor the perimeter,
not the hazardous area inside.
Additionally, mats can also simplify routine tasks such as
machine setup, maintenance and repair.
Applications can be
found throughout industry
and typically include the
following areas:
• Welding Robots
• Assembly Machinery
• Material Handling
• Packaging Machinery
• Punches
• Presses
• Robotic Work Cells
mat Specifications
Mat Type:
Mode:
Mat Size:
Normally open SPST, four-wire
Pressure Sensitive
Standard sizes from 12 x 12 in. (305
x 305 mm) to 48 x 72 in. (1219.2 x
1829.8 mm)
Metric sizes from 300 x 300 mm
(11.8 x 11.8 in.) to 1200 x 1800 mm
(47.2 x 70.9 in.)
Detects adults > 30 kg. (66 lbs.)
Self extinguishing. Meets UL94VO
13.5 mm (0.54 in.)
PVC
80 (±3) shore A
18-gauge, 4-conductor, 16-strand,
300 VAC, with MC12DC male single
key connector. 5 m (16 ft.) long.
-37 to 66°C (-35 to 150° F)
IP67
ANSI/RIA 15.06-1999, ANSI
B11.19-2003, OSHA 1910.217(b),
CSA Z432-04
When used with an MC3, MC4 or
MC6 controller the UM series safety
mats comprise a system which
has been EC type examined to the
requirements of category 3, EN
954-1 and EN1760-1:1998.
Activation Force:
Mat Flammability:
Mat Housing Cross Section:
Mat Cover Material:
Durometer:
Mat Cable:
Operating Temperature:
Environmental:
Conforming to Standards:
f
mat chemical resistance*
Water
Mineral Acids
Organic Acids
Alcohols
Aldehydes
Caustics
Petroleum Solvents
Organic Solvents
Chlorinated Solvents
*40 minute exposure @ 23°C (74°F)
Excellent
Good/Excellent
Good/Excellent
Good
Good/Excellent
Good/Excellent
Good
Poor
Poor
Approvals:
Specifications are subject to change without notice.
specifications and dimensions on
✎
For MC Controllers, see www.sti.com
the
mat Selection
Multiple UM series mat sizes are offered. A system can easily
be configured to meet almost any guarding requirement.
Standard mat Sizes
Widths
12 to 48 in. (6 in. increments)
Lengths
12 to 72 in. (6 in. increments)
metric mat Sizes
Widths
500 to 1200 mm
Lengths
500 to 1800 mm
custom mat Sizes
Widths
Up to 48 in.
Lengths
Up to 72 in.
OmrOn Scientific technOlOgieS, inc.
USA
Tel. 1/888/510-4357
canada
Tel. 1/866/986-6766
For the Latest Information
On the Internet:
www.sti.com
f3
Um Series
Safety mats & Area guarding
trim Selection
Several choices are available in trim selection and can be
customized to a specific application.
Aluminum Blunt trim
Used to finish off the edge of a mat installation near a wall or
machine. Helps hold mats in place.
two-Part ramp trim with Yellow PVc cover
This trim simplifies routing of cables and replacement of dam-
aged mats. To position the mats correctly, place all of the mats in
the approximate position, place the joining trim between the mats,
then temporarily place the cover on the joining trim. Square the
mats by sliding the ramp trim under the mats. When all of the mats
are correctly positioned, anchor the perimeter trim to the floor.
After the wires have been routed, a rugged cover of highly visible,
safety yellow PVC is snapped into place. Corners can either
be mitered or be Omron STI's exclusive molded corners. (See
illustrations on this page.)
Aluminum ramp trim
This single part aluminum ramp trim is available for areas where
the two part ramp trim may not be suitable.
molded corners
Eliminates the need to miter the corners of perimeter trim.
Designed to mate with Omron STI two-part ramp trim.
two-Part ramp trim with Aluminum cover
f
This trim is the same as above except that the PVC cover is
replaced with an aluminum cover that is attached by screws to the
base. (See the Dimensions Section of this datasheet for details.)
two-Part Active Joining trim
Similar in concept to the two-part ramp trim, this trim provides
an "active" joint where the perimeters of two mats adjoin each
other. When a person steps on the surface cover of the active
joining trim, the Universal Mat system will detect their presence
and send a stop signal to the guarded machine.
PVC Trim Cover
Aluminum
Floor
f4
OmrOn Scientific technOlOgieS, inc.
USA
Tel. 1/888/510-4357
canada
Tel. 1/866/986-6766
For the Latest Information
On the Internet:
www.sti.com
Um Series
Safety mats & Area guarding
trim Dimensions
Outside molded corner trim
Model UMOC
30.58
1.204
58.42
2.300
(mm/in.)
2-Part Joining trim (Base and cover)
1.02
0.040
14.1
0.555
17.02
0.670
35.81
1.410
72.39
2.850
94.62
3.725
58.42
2.300
101.6
4.000
23.1
0.910
94.62
3.725
72.39
2.850
30.58
1.204
2-Part Joining Trim: PN 43222-0096
Joining Trim Aluminum Base: PN 32592
Joining Trim Cover Black: PN 32591
Joining Trim Cover Yellow: PN 32591-0010
Molded Outside Corner: PN 25836
2-Part ramp trim with PVc cover (tKm)
58.9
2.32
11.8
0.47
f
inside molded corner trim
Model UMIC
21.89
0.862
57.48
2.263
72.39
2.850
94.62
3.725
57.48
2.263
91.4
3.60
18.4
0.72
Aluminum Base & PVC Cover: PN 43123-0096
Aluminum Base: PN 32667
PVC Cover: PN 32668
2-Part ramp trim with Aluminum cover (tKAt)
72.39
2.850
21.89
0.862
58.9
2.32
94.62
3.725
Molded Inside Corner: PN 25837
Blunt trim
10.8
0.425
13.72
Ref
0.540
25.4
Ref
1.00
13.72
0.540
Aluminum Base & Aluminum Cover: PN 43123-1096
Aluminum Base: PN 32667
Aluminum Cover: PN 26441
Aluminum Single Part ramp trim (tKA)
10.64
0.419
19° Ref
13.72
Ref
0.540
19.53
0.769
63.50
Ref
2.500
9.35
0.367
7.59
Ref
0.299
Blunt Trim: PN 43223-0096
Aluminum Ramp Trim: PN 43224-0096
OmrOn Scientific technOlOgieS, inc.
USA
Tel. 1/888/510-4357
canada
Tel. 1/866/986-6766
For the Latest Information
On the Internet:
www.sti.com
f5
Um Series
Safety mats & Area guarding
two-Part trim with PVc cover and mitered corners (tKm)
PVC Trim Cover
Safety Mat
Aluminum Trim Base
12.7
0.50
(Ref)
56.79
2.236
50.8
2.00
Anchor
Slide Alum Base Under Mat
MAT FASTENING DETAIL
Screw
4-Cond Cable with
MC12DC Male Single Key
4-Term Connector
25.4
1.00
45°
f
L = Mat Length
(PVC Trim Cvr) A = L +
(Aluminum
137.4
B=L+
Trim Base)
5.41
609.6 Shown
24.0
114.8
4.52
724.4 Shown
28.52
104.5
4.115
(Ref)
Cable
Conduit
Drill Holes
in Groove
on Boss
(#8 x 1.25"
Screw)
746.8 Shown. TOL = - 0.381 / +0
29.41
- 0.015 / +0
STI To Cut Alum Trim "Rib"
25.4 (1.00) Section Here
two-Part trim with PVc cover and molded corners (tKc)
Safety Mat
Slide Alum Base Under Mat
PVC Trim Cover
Aluminum Trim Base
Corner
MAT FASTENING DETAIL
Screw
Anchor
12.7
0.50
(Ref)
56.79
2.236
50.8
2.00
4-Cond Cable with
MC12DC Male Single Key
4-Term Connector
25.4
1.00
(PVC Trim Cvr) A = L -
50.8 TOL = - 0.381 / +0
2.00
- 0.015 / +0
50.8 TOL = - 0.381 / +0
(Alum Base) B = L -
2.00
- 0.015 / +0
L = Mat Length
138.2
(Overall Length) C = L +
5.44
104.5
4.115
(Ref)
Cable
Conduit
Drill Holes
in Groove
on Boss
(#8 x 1.25"
Screw)
STI To Cut Alum Trim "Rib"
25.4 (1.00) Section Here
f6
OmrOn Scientific technOlOgieS, inc.
USA
Tel. 1/888/510-4357
canada
Tel. 1/866/986-6766
For the Latest Information
On the Internet:
www.sti.com
工作这点儿事
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
