STMicroelectronics
ST7-EPB
Programming board
UM0028
User manual
Rev 4
June 2006
www.st.com
UM0028
User manual
ST7-EPB
Programming board
Introduction
Thanks for choosing ST7! This manual will help you setup and start using your ST7-EPB programming
board.
ST7-EPB programming boards allow you to program ST7 microcontrollers that have EPROM, EEPROM
and FLASH memories. Your programming board links, via parallel port, to a host PC running ST7 Visual
Programmer (STVP7) software. This software interface allows you to customize and control the
programming of an application to your ST7.
The layout of your programming board varies depending on the type of EPB you have ordered, as each
programming board is designed to program a different sub-family of ST7 MCUs.
Some programming boards also support either In-Circuit Programming (ICP), or In Situ Programming
(ISP) of your ST7 while it is mounted on your application board.
Note:
A complete listing of the ST7 family of programming tools, including the devices and
programming modes that they support is provided in
ST7 Visual Programmer (STVP7°
Release Notes.
Figure 1.
Programming board with ICC cable
Parallel port
(P1 connector)
Programming
sockets
ICC cable
ICC connector
(10-pin, HE-10 connector)
June 2006
UM0028 Rev 4
3/15
www.st.com
Introduction
ST7-EPB
About the user manuals...
This manual will help you setup your ST7-EPB programming board and connect it to your PC. Here, you
will find:
■
■
Setup instructions
Information about in-circuit programming connections
For information about the hardware and software intended for use with your programming board, refer to
the following documents that are included with it:
■
■
■
■
ST7 Visual Programmer online help
- program your MCU
ST7 Programming Board Descriptions
- a complete list of programming boards, including the
devices and programming modes they support
In-Circuit Programming Considerations
- information about setting up your application board for in-
circuit programming
ST7xxxx Datasheet
- programming information that is specific to your MCU
Host PC system requirements
Both the hardware and software that you will use to program your ST7 have been designed to operate
with:
■
■
■
■
Microsoft
®
Windows
®
2000 or XP
®
.
Intel
®
Pentium (or compatible) processor with minimum speed of 133 MHz.
Minimum RAM of 32 MB (64 MB recommended).
60 MB of free hard disk space to install all of the ST7 tools.
Windows
®
2000 and XP
®
users must have administrator privileges to install STVP7.
Note:
Getting assistance
For more information, application notes, FAQs and software updates relevant to all the ST microcontroller
families, check out the CD-ROM or our website:
www.st.com/mcu
For assistance on all ST microcontroller subjects, or for help using your programming board, refer to the
contact list provided in
Product Support
on page 14. We’ll be glad to help you.
4/15
UM0028 Rev 4
ST7-EPB
Contents
1
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1
1.2
1.3
1.4
1.5
Delivery Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Setting up your ST7-EPB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using the programming sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using an in-circuit programming connection . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Additional information about programming in ISP mode . . . . . . . . . . . . . . . . 10
2
Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.1
2.2
Parallel port connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
About jumpers on the ST7 EPB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Appendix A Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Appendix B Safety Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Appendix C Product Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
UM0028 Rev 4
5/15
微控制器 MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
