金 龙 机 电 股 ½ 有 限 公 司
JINLONG MACHINERY & ELECTRONICS CO., LTD.
sales@jinlong-machinery.com
www.jinlong-machinery.com
产
品
规
格
书
PRODUCT SPECIFICATION
客户名称/Customer
客户料号/Part
No.
客户承认签章
Customer Approved
Signatures
品名/Description
型号/Part
No.
设计/
Designed by
水平线性振动电机
Horizontal linear vibration motor
LVM061530
审核/Verified
by
批准/Approved
by
Yu haijiang
James
产
品
规
格
书
LVM061530
Page： 1 / 9
PRODUCT SPECIFICATION
重要提示
IMPORTANCE NOTES:
1.
如对电机的性½和/或寿½有任½争议，仅基于此规格书做出判断。
If there is any argument on motor performance and/or life, judgment is to be made based on this
specification only.
2.
客户方有责任确认该电机½满足您的½用要求。
Customer has the responsibility to verify that the motor can meet the requirement of your application.
3.
如果贵公司未提供技术规格，该文件将详细叙述与贵公司商定的技术规格。
In the event that an official specification is not being presented by customer; this document will
specify the agreed technical specification.
4.
收到此规格书后，贵司应于下订单之前将规格书副本签回以示贵司已确认。如贵司未½在规定
时间内签回副本，我司将认为贵司已收到并承认该规格书。
After the receipt of this specification, customer has to send a signed copy to KOTL as a confirmation
before placing purchase order In the event of no receipt of signed copy before required date, the
specification will suppose being received and acknowledged.
更 改 记 ½
Revision History
版次
Rev.
01
02
日期
Date
2015/03/28
2015/04/16
变更内容
Description of the Change
Initial Release
Modified Input Voltage Range
Rate Power, Internal
Resistances, Resonant
Frequency and Acceleration
Modified
Rated Power,
编制
Designed by
Yuyu
Yuyu
审核
Verified by
批准
Approved by
James
James
Internal Resistances,
03
2015/05/28
Resonant Frequency
Acceleration specification
Add Rise time and brake
time
Yu Haijiang
James
www.jinlong-machinery.com
产
品
规
格
书
LVM061530
Page： 2 / 9
PRODUCT SPECIFICATION
1.
适用范围/Application
本说明书适用于线性电机LVM061530
This specification applies to Linear Motor LVM061530
2.
结构/Configuration
序号
NO.
2-1
2-2
项目
Item
外½尺寸
Motor structure
重量
Weight
内容
Contents
15mm×
6mm×
3mm（长×
高）
½×
15mm×
6mm×
3mm（Length × Width × Height）
约
2.0
克
2.0g（Approx.）
3.
基本规格/Basic
Specifications
序号
NO.
3-1
项目
Item
操½驱动
Operation driver
额定电压
Rated voltage
额定功率
Rated Power
内阻
Internal Resistances
Insulation Resistance
绝缘阻值
Operating conditions
½用环境
Storage conditions
贮存环境
规格
Specification
可扫频信号发生器
signal generator
with sweep
frequency
2.0 Vrms
条件/备注
Condition / Remark
频率为F0 点，范围参见共振频率
@ F0，refer to resonant frequency
3-2
3-3
3-4
3-5
正弦波或方波
Sinewave or square wave
输入额定电压
~300mW@ 2.0Vrms
With rated voltage
11±1.5Ω
Min 10 MΩ
20℃常湿常压
在端子和外壳之间通
100V DC
100V DC between terminal and
housing
常规湿度，无水½凝结
ordinary humidity ,no condensation of
moisture
常规湿度，无水½凝结
ordinary humidity ,no condensation of
moisture
3-6
-20℃~70℃
3-7
-40℃~80℃
4.
性½/Performance
序号
项目
NO.
Item
共振频率
4-1
Resonant frequency
加速度
4-2
Acceleration
4-3
Rise time启动时间
4-4
Brake time停止时间
规格
Specification
200Hz ±
10Hz
≥0.8Grms
@ 100g
Jig@F0
<100ms
<120ms
条件/备注
Condition / Remark
参考性½测试条件
Refer to test conditions
参考性½测试条件
Refer to test conditions
0→90% of Acceleration加速度
100%→10% of Acceleration加速度
www.jinlong-machinery.com
产
品
规
格
书
LVM061530
Page： 3 / 9
PRODUCT SPECIFICATION
序号
NO.
4-5
噪音
Noise
项目
Item
规格
Specification
≤45dBA
条件/备注
Condition / Remark
距离电机
10cm处测量
10cm from vibrator
5. Test Conditions/性½测试条件
序号
项目
NO.
Item
温度
5-1
Temperature
湿度
5-2
Humidity
驱动信号
5-3
Test Driver
驱动电压
5-4
Input Voltage Range
测试工装材质及重量
5-5
Material & weight of jig
测试条件
Test Conditions
25±
2℃
65±20％ RH
BAKO以F0
频率驱动
BAKO tester frequency @ F0
2.0Vrms
铝合金
100
克
Aluminum 100g
传感器在测试工装的左侧壁上，并½其½于测试工装的中
心½线上。
The sensor is on the left wall of the testing jig, also is at the
center axis.
电机在测试工装中的½½需与传感器在同一½线上，电机
中心与传感器的距离为
69.5mm。
The location of the motor in test jig should be at the same
axis with sensor, and the distance between motor canter and
sensor is 69.5mm.
5-7
电机及传感器相对测试
工装的½½
Position of vibrator and
sensor in test jig
www.jinlong-machinery.com
产
品
规
格
书
LVM061530
Page： 4 / 9
PRODUCT SPECIFICATION
序号
NO.
项目
Item
测试条件
Test Conditions
传感器/
Sensor:
通过石蜡粘结
bonding with paraffin
电机/
Motor：
通过双面胶将电机底部固定在工装表面。双面胶型号为
Nitto Denko 5603BN
Fixing the motor bottom on the jig face with double-sided
glue tape. (Model of the tape: Nitto Denko 5603BN)
通过电机上方和工装间的泡棉，压紧电机。泡棉型号为：
3M 467MP
Tighten the motor with the foam between motor and jig.
Model of the foam: 3M 467MP
将测试工装½于鸡蛋棉表面的正中间。信号源输出信号½
电机振动，传感器接受振感，并将信号传至接收器
Place the testing jig at the right center of eggs cotton. Signal
from the signal source vibrates motor, and sensor receive the
vibration and send the signal to receiver.
5-8
固定方式
Fix method
5-9
测试方法
Test method
egg crate foam
鸡蛋棉规格为：
20cm×20cm×6.5cm
（长度×½度×高度）
Size of the egg crate foam:20cm×
20cm×
6.5cm（L× H）
W×
6. Reliability Test/可靠性试验
每项试验测试
16
只电机，可靠性试验后，所有样品必须符合以下标准：
Test 16 pcs for each test. After reliability test, all sample must be meet the requirement as below:
a)
频率变化量在原始频率±
5%以内/Resonant frequency: within±5% of original
b)
加速度/Acceleration: ≥0.75
Grms@2Vrms
c) Rise time:
≤130ms启动时间
d) Break time:
≤170ms停止时间
e)
噪音/Noise: ≤50dBA噪音
备注：试验后，需常温下至少放½四小时后测试电机性½。
NOTE:
Test the function after at least 4 hours exposure in ordinary temperature.
www.jinlong-machinery.com
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
