Swanstrom
STUSA Electronic Tools
•
•
•
•
•
•
•
•
Engineered for small hands and intricate work
Forged steel for strength, durability, and long life
Machined with precision for tight tolerances
Hardened electronically, tempered for toughness
Honed to precise cut requirements
Stainless steel leaf springs welded in place
Cushioned grips for operator comfort
ESD SAFE for component protection
MX54
Oval head semi-flush diagonal cutters
• Strongest tips and beveled edge for long life
• Induction hardened edges optimize cutting ease and life
• OAL 4.25” Jaw 0.60”
MX54-9
Oval head diagonal flush cutters
• Strong tips and long life
• Induction hardened edges optimize cutting ease and life
• Flush cut for a sharper edge requiring less squeeze and reduces
spike
• OAL 4.25” Jaw 0.60”
STUSA Electronic Tools
MX54-3
Oval relieved/slim diagonal flush cutters
• For intricate and repetitive work between and under closely
spaced components
• Induction hardened edges optimize cutting ease and life
• Flush cut for a sharper edge requiring less squeeze and reduces
spike
• OAL 4.25” Jaw 0.60”
MX54-5
Taper head diagonal flush cutters
• For intricate work between closely spaced components
• Induction hardened edges optimize cutting ease and life
• Flush cut for a sharper edge requiring less squeeze and reduces
spike
• OAL 4.25” Jaw 0.60”
EMX54-3
Oval relieved/slim diagonal flush cutters
with ergonomic handles
• For intricate and repetitive work between and under closely
spaced components
• Induction hardened edges optimize cutting ease and life
• E denotes ergonomic (double curve) handles to spread pressure
across the palm and relieve carpal tunnel
pocket pressure
• Most comfortable hand, wrist and arm positions
• Flush cut for a sharper edge requiring minimum squeeze
and reduces spike
• OAL 5.60” Jaw 0.60”
EAX54
Angle end flush cutters with ergonomic handles
• Angled 60º/30º for ergonomic work positions
• Induction hardened edges optimize cutting ease and life
• E denotes ergonomic (double curve) handles to spread pressure
across the palm and relieve carpal tunnel
pocket pressure
• For most comfortable hand, wrist and arm positions
• Flush cut for sharper edge, minimum squeeze, maximum ease
• OAL 5.70” Jaw 0.63”
18
19
AX54
Angle end flush cutters
• Angled 60º/30º for most ergonomic work positions
• Induction hardened edges optimize cutting ease and life
• Flush cut -for a sharp edge requiring less squeeze and reduces
spike
• OAL 4.75” Jaw 0.63”
LX4
Submini needle nose serrated pliers
• Where short handles are a must
• Each jaw has fine parallel serrations and beveled edges
• OAL 4.50” Jaw 0.92”
LX4G
Submini needle nose smooth pliers
• Where short handles are a must
• Each jaw is smooth with beveled edges
• OAL 4.50” Jaw 0.92”
LX54
LX54G
Thin long nose serrated pliers
• Each jaw has fine parallel serrations and beveled edges
• OAL 5.25” Jaw 1.02”
Thin long nose smooth pliers
• Each jaw is smooth with beveled edges
• OAL 5.25” Jaw 1.02”
STUSA Electronic Tools
NX54
NX54G
Slim needle nose serrated pliers
• Each jaw is serrated with beveled edges
• OAL 5.25” Jaw 1.02”
Slim needle nose smooth pliers
• Each jaw is smooth with beveled edges
• OAL 5.25” Jaw 1.02”
DX54G
Flat nose smooth pliers
• Strongest gripping plier
• Ideal for straightening flat leads
• OAL 5.25” Jaw 1.02”
RX54
Round nose smooth jaw pliers
• Used to form perfectly round loops without deformation
• OAL 5.25” Jaw 1.02”
CX54G
Curve nose smooth jaw pliers
•
•
•
•
A very ergonomic alternative to long nose pliers
Each jaw is smooth with beveled edges
Permits most comfortable arm position for working
OAL 5.25” Jaw 1.03”
19
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
