100 Series
Media Converter &
Industrial Ethernet Switches
User Manual &
Installation
Guide
(Revised 9/23/2009)
1
Industrial Media Converter Installation Guide
102MC-XX
102MCE-XX-YY
104TX
105TX
105FX-XX
105FXE-XX-YY
106FX2
108TX
108TX-HV
Where: XX = ST or SC and YY = -15, -40, or -80
(Revised 9/23/2009)
2
Copyright, © N-TRON Corp., 2008
820 S. University Blvd., Suite 4E
Mobile, AL USA 36609
All rights reserved. Reproduction, adaptation, or translation without prior written permission from N-TRON
Corp. is prohibited, except as allowed under copyright laws.
Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos
or other designations mentioned herein are trademarks of their respective owners.
The information contained in this document is subject to change without notice. N-TRON Corp. makes no
warranty of any kind with regard to this material, including, but not limited to, the implied warranties of
merchantability or fitness for a particular purpose. In no event shall N-TRON Corp. be liable for any
incidental, special, indirect or consequential damages whatsoever included but not limited to lost profits
arising out of errors or omissions in this manual or the information contained herein.
Contact Information
N-TRON Corp.
820 South University Blvd.
Suite 4E
Mobile, AL 36609
TEL: (251) 342-2164
FAX: (251) 342-6353
Website:
www.n-tron.com
Email:
N-TRON_Support@n-tron.com
(Revised 9/23/2009)
3
GENERAL SAFETY WARNINGS
WARNING:
Do not operate the equipment in the presence of flammable gasses or fumes. Operating
electrical equipment in such an environment constitutes a definite safety hazard.
WARNING:
If the equipment is used in the manner not specified by N-TRON Corp., the protection provided
by the equipment may be impaired.
WARNING:
Do not perform any services on the unit unless qualified to do so. Do not substitute
unauthorized parts or make unauthorized modifications to the unit.
WARNING:
hazard.
Do not operate the unit with the end plates removed, as this could create a shock or fire
WARNING:
Do not operate the equipment in a manner not specified by this manual.
ENVIRONMENTAL SAFETY WARNINGS
WARNING:
Disconnect the power and allow to cool 5 minutes before touching.
ELECTRICAL SAFETY WARNINGS
WARNING:
Disconnect the power cable before removing the end plates.
WARNING:
Do not operate the unit with the end plates removed.
WARNING:
Do not work on equipment or cables during periods of lightning activity.
WARNING:
Do not perform any services on the unit unless qualified to do so.
WARNING:
Observe proper DC Voltage polarity when installing power input cables. Reversing voltage
polarity can cause permanent damage to the unit and void the warranty.
(Revised 9/23/2009)
4
HAZARDOUS LOCATION INSTALLATION REQUIREMENTS
1. This equipment is suitable for use in Class I, Div 2, Groups A, B, C, and D, or unclassified or non-
hazardous locations only.
2.
WARNING:
Explosion Hazard - Substitution of components may impair suitability for Class I,
Division 2.
3.
WARNING:
Explosion hazard, do not disconnect while the circuit is live or unless the area is known to be
non-hazardous.
4.
WARNING:
Explosion Hazard - Do not remove or replace the device unless power has been switched off
or the area is known to be non-hazardous.
5. Use 60/75ºC rated Copper wire, (0.22Nm) 2 inch-lbs Tightening torque for field installed connectors.
6.
WARNING:
Install only in accordance with Local & National Codes of Authorities Having Jurisdiction.
7. Class I, Div 2 Installations require that power connections must be current limited at the power source with
an in-line fuse rated at 0.5A.
8. Class I, Div 2 installations require that all devices connected to this product must be UL listed for the area in
which it is installed.
9. Limited Operating Voltage: 12-30V for Class I, Div 2 installations.
(Revised 9/23/2009)
5
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
