2. Soldering the headers
Before using your click board™, make sure
to solder 1x8 male headers to both left
and right side of the board. Two 1x8 male
headers are included with the board in
the package.
Accel
click
1. Introduction
1
3
4. Essential features
Accel Click™ with it’s
ADXL345
module
supports several sensing functions such as
single/double tap detection, activity/inactivity
monitoring, free-fall detection etc. It has
memory management system with a 32-level
FIFO buffer to store data with minimized host
processor activity. All these features make
this board ideal for mobile devices, medical
and industrial instrumentation, navigation
devices, hard drive protection and more.
2
Turn the board upside down so that
bottom side is facing you upwards. Place
shorter parts of the header pins in both
soldering pad locations.
Turn the board upward again. Make sure
to align the headers so that they are
perpendicular to the board, then solder the
pins carefully.
Accel Click™ is an accessory board in
mikroBUS™
form factor. It’s a compact
and easy solution for adding accelerometer
functionality to your device. It features
ADXL345
3-axis accelerometer module with
ultra-low power and high resolution (13-bit)
measurement. Accel Click™ communicates
with target board via I
2
C or SPI interface. The
Board is designed to use 3.3V power supply
only. It has a LED diode (GREEN) which
indicates the presence of power supply.
3. Plugging the board in
Once you have soldered the headers your
board is ready to be placed into desired
mikroBUS™ socket. Make sure to align the
cut in the lower-right part of the board with
the markings on the silkscreen at the
mikroBUS™ socket. If all of the pins
are aligned correctly, push the
board all the way into the socket.
click
www.mikroe.com
Accel click Manual
ver. 1.00
BOARD
0 100000 020968
5. Accel Click™ Board Schematic
6. SMD Jumpers
The Accel Click™ board communicates
with the main board via I
2
C or SPI interface
depending on the position of the
J1, J2
and
J3
SMD jumpers. These jumpers are soldered in
I
2
C interface position by default. There is an
option to select the alternate address with
jumper
J4
in the case of I
2
C interface (default
position is logic 1).
VCC-3.3
R2
10K
SCK
SCK/SCL
SCL
SDI
SDI/SDA
SDA
SDO
SDO/ADD
VCC-3.3
J3
SPI
I2C
J1
SPI
I2C
J2
1
0
J4
R3
10K
SPI
I2C
VCC-3.3
VCC-3.3
VCC-3.3
VCC-3.3
14
SCK/SCL
U1
SDA
ADD
Res
NC
INT2
INT1
13
12
11
10
9
8
SDI/SDA
SDO/ADD
1
2
3
4
5
6
VCC-3.3
7. Code Examples
AN
RST
CS
SCK
MISO
MOSI
+3.3V
GND
PWM
INT
TX
RX
SCL
SDA
+5V
GND
INT
SCL
SDA
C1
100nF
C2
100nF
LD1
CS
VCC
GND
Res
GND
GND
VCC
SCL
R1
2K2
INT
R4 220
CS
CS
SCK
SDO
SDI
ADXL345
MIKROBUS DEVICE CONN.
R5100K
Once you have done all the necessary
preparations, it’s time to get your click
board™ up and running. We have provided
the examples for mikroC, mikroBasic and
mikroPascal compilers on our
Libstock
website. Just download them and you are
ready to start.
7
.com
8. Support
MikroElektronika offers
Free Tech Support
(www.mikroe.com/esupport)
until the
end of product lifetime, so if something goes
wrong, we are ready and willing to help!
MikroElektronika assumes no responsibility or liability for any errors or inaccuracies that may appear in the present document.
Specification and information contained in the present schematic are subject to change at any time without notice. Copyright © 2012 MikroElektronika. All rights reserved.
微控制器 MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
