Double Coated Tape with
Quick Bonding
Adhesive 360
9628B
•
9628FL
•
9629PC
•
9629B
•
9629FL
Technical Data
September, 2009
Product Description
3M™ Double Coated Tapes with 3M™
Quick Bonding
Adhesive 360 provides high
bond strength to
most surfaces, including many low surface energy plastics such
as polypropylene and
powder coated paints.
Construction
Product
Number
Faceside
1
Adhesive
Type/
Thickness
Carrier
Type/
Thickness
0.0005”
(0.013 mm)
Black PET
0.0005"
(0.013 mm)
Clear PET
0.0005”
(0.013 mm)
Clear PET
0.0005”
(0.013 mm)
Black PET
0.0005”
(0.013 mm)
Clear PET
Backside
2
Adhesive
Type/
Thickness
0.00075"
(0.019 mm)
Liner
Color, Type,
Print
Natural, 60#
Glassine
Liner
Caliper
3
0.0032"
(0.08 mm)
Total Tape
Thickness
(w/o liner)
0.002"
(0.05 mm)
3M™ Double 0.00075"
Coated Tape (0.019 mm)
9628B
3M™ Double 0.00075"
Coated Tape (0.019 mm)
9628FL
3M™ Double
Coated Tape
9629PC
0.00175"
(0.04 mm)
0.00075"
(0.019 mm)
Clear,
Polyester
0.002"
(0.05 mm)
0.002"
(0.05 mm)
0.00175"
(0.04 mm)
Tan, 58#
Polycoated
0.0042"
(0.11 mm)
0.004"
(0.10 mm)
3M™ Double 0.00175"
Coated Tape (0.04 mm)
9629B
3M™ Double 0.00175"
Coated Tape (0.04 mm)
9629FL
0.00175"
(0.04 mm)
Natural, 60#
Glassine
0.0032"
(0.08 mm)
0.004"
(0.10 mm)
0.00175"
(0.04 mm)
Clear,
Polyester
0.002"
(0.05 mm)
0.004"
(0.10 mm)
Note 1:
Faceside (FS) adhesive is on the interior of the roll, exposed when unwound.
Note 2:
Backside (BS) adhesive is on the exterior of the roll, exposed when liner is removed.
Note 3:
The caliper listed is based on a calculation from manufacturing controlled adhesive coat
weights using a density of 1.071 g/cc.
3M
™
Double Coated Tape with
Quick Bonding
Adhesive 360
9628B • 9628FL • 9629PC • 9629B • 9629FL
Typical Physical
Properties and
Performance
Characteristics
Note: The following technical information and data should be considered representative
or typical only and should not be used for specification purposes.
2.0 mil (0.05 mm)
3M™ Double Coated Tape
9628B • 9628FL
Oz/in
(N/25 mm)
Faceside / Backside
60 (17) / 60 (17)
65 (18) / 65 (18)
90 (25) / 90 (25)
Oz/in
(N/25 mm)
Faceside / Backside
90 (25) / 90 (25)
115 (32) / 115 (32)
100 (28) / 100 (28)
50 (14) / 50 (14)
60 (17) / 60 (17)
4.0 mil (0.10 mm)
3M™ Double Coated Tape
9629PC • 9629B • 9629FL
Oz/in
(N/25 mm)
Faceside / Backside
100 (28) / 100 (28)
120 (34) / 120 (34)
150 (42) / 150 (42)
Oz/in
(N/25 mm)
Faceside / Backside
160 (45) / 150 (42)
170 (48) / 160 (45)
170 (48) / 160 (45)
65 (18) / 65 (18)
75 (21) / 65 (18)
Product Number
Adhesion to Polypropylene
ASTM D3330 – 180 degree,
2 mil al foil
- 30 seconds RT
- 15 minutes RT
- 72 hours RT
Adhesion to other surfaces
ASTM D3330 – 180 degree,
2 mil al foil, 72 hour RT
ABS
Polycarbonate
Stainless Steel
LDPE
HDPE
Shear Strength - ASTM D3654
Modified – (.5 inch
2
sample size)
1000 grams at 72°F (22°C)
500 grams at 158°F (70°F)
Relative High Temperature
Operating Ranges:
Long Term (days, weeks)
Short Term (minutes, hours)
Relative Solvent Resistance:
>10,000 minutes
>10,000 minutes
>10,000 minutes
>10,000 minutes
200°F (93°C)
350°F (177°C)
Very Good
200°F (93°C)
350°F (177°C)
Very Good
Available Sizes
Roll length, width, slitting tolerance, core size.
Product
Maximum Length in.:
1/2" to 1/2"
1/2" to 1"
1" to 6"
6" to 27"
27" to 54"
Normal Slitting Tolerance
Core Size (ID)
Minimum length
3M™ Double Coated Tape
9628B • 9628FL
9629PC • 9629B
72 yds. (66 m)
360 yds. (329 m)
540 yds. (494 m)
900 yds. (823 m)
540 yds. (494 m)
72 yds. (66 m)
252 yds. (230 m)
540 yds. (494 m)
720 yds. (658 m)
540 yds. (494 m)
± 1/32 in. (0.08 mm)
3.0 in. (76.2 mm)
72 yds. (66 m).
9629FL
72 yds. (66 m)
360 yds. (329 m)
540 yds. (494 m)
900 yds. (823 m)
540 yds. (494 m)
-2-
3M
™
Double Coated Tape with
Quick Bonding
Adhesive 360
9628B • 9628FL • 9629PC • 9629B • 9629FL
Features
• Excellent adhesion to difficult to bond to surfaces such as HDPE, LDPE, and PP.
• Super quick stick.
• Higher adhesion from a thinner tape.
• Excellent solvent resistance.
• High temperature performance.
• This tape has a film carrier which can add dimensional stability to foam and
other substrates and also make it easier to handle the tape during slitting and
die-cutting.
Application
Techniques
Bond strength is dependent upon the amount of adhesive-to-surface contact
developed. Firm application will assist the adhesive in developing intimate contact
with the bonding surface. To accelerate the adhesion process, additional heat, up to
130°F (54°C), may be used.
To obtain optimum adhesion, the bonding surfaces must be clean, dry, and well
unified. Some typical surface cleaning solvents are isopropyl alcohol or heptane.*
Ideal tape application temperature range is 70°F to 100°F (21°C to 38°C). Initial
tape application to surfaces at temperatures below 50°F (10°C) is not recommended
because the adhesive becomes too firm to adhere readily. However, once properly
applied, low temperature holding is generally satisfactory.
*When
using solvents, extinguish all ignition sources, including pilot lights, and
follow the manufacturers precautions and directions for use. These cleaning
recommendations may not be compliant with the rules of certain Air Quality
Management Districts in California; consult applicable rules before use.
Environmental
Performance
Humidity Resistance:
High humidity has minimal effect on adhesive performance.
No significant reduction in bond strength is observed after exposure for 7 days at
90°F (32°C) and 90% relative humidity.
UV Resistance:
When properly applied, nameplates and decorative trim parts are
not adversely affected by exposure.
Water Resistance:
Immersion in water has no appreciable effect on the bond
strength. After 100 hours at room temperature, the high bond strength is maintained.
Temperature Cycling Resistance:
High bond strength is maintained after cycling
four times through:
8 hours at 194°F (90°C)
16 hours at -40°F (-40°C)
8 hours at 100.4°F (38°C/100% RH)
16 hours at -40°F (-40°C)
Chemical Resistance:
When properly applied, nameplate and decorative trim parts
will hold securely after exposure to numerous chemicals including oil, mild acids,
and alkalis.
Application Ideas
• Foam to powder coated painted surfaces.
• Low surface energy plastic adhesion.
-3-
3M
™
Double Coated Tape with
Quick Bonding
Adhesive 360
9628B • 9628FL • 9629PC • 9629B • 9629FL
Application Equipment
To apply adhesives in a wide web format, lamination equipment is required to
ensure acceptable quality. To learn more about working with pressure-sensitive
adhesives please refer to technical bulletin,
3M™ Lamination Techniques for
Converters of Laminating Adhesives
(70-0704-1430-8).
For additional dispenser information, contact your local 3M sales representative, or
the toll free 3M sales assistance number at 1-800-362-3550.
Storage
Store in original cartons at 70°F (21°C) and 50% relative humidity.
Shelf Life
If stored under proper conditions, product retains its performance and properties for
two years from date of manufacture.
Technical Information
The technical information, recommendations and other statements contained in this document are
based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such
information is not guaranteed.
Product Use
Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use
and performance of a 3M product in a particular application. Given the variety of factors that can affect
the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and
determining whether it is fit for a particular purpose and suitable for user’s method of application.
Warranty,
Limited Remedy,
and Disclaimer
Unless an additional warranty is specifically stated on the applicable 3M product packaging or product
literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time
3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY
OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE.
If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s
option, replacement of the 3M product or refund of the purchase price.
Limitation of Liability
Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M
product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory
asserted, including warranty, contract, negligence or strict liability.
ISO 90 01 2000
:
This Industrial Adhesives and Tapes Division product was manufactured under a 3M quality system registered to ISO 9001: 2000 standards.
Industrial Adhesives and Tapes Division
Converter Markets
3M Center, Building 225-3S-06
St. Paul, MN 55144-1000
800-223-7427 • 651-778-4244 (fax)
www.3M.com/converter
Recycled Paper
40% pre-consumer
10% post-consumer
3M is a trademark of 3M Company.
Printed in U.S.A.
©3M 2009 70-0713-4544-4 (9/09)
-4-
/201809304025888_pdf/pg_0001.png)
电子竞赛
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界/201809304025888_pdf/1.png)
/201809304025888_pdf/2.png)
/201809304025888_pdf/3.png)
/201809304025888_pdf/4.png)
/201809304025888_pdf/pg_0002.png)
/201809304025888_pdf/pg_0003.png)
/201809304025888_pdf/pg_0004.png)
