10.2kVDC Isolated 6W Gate Drive SM DC-DC Converters
Output 1
Rated Output Current
Rated Output Voltage
Rated Output Voltage
Output 2
Rated Output Current
Output Power
Order Code
1
Input
Voltage
Range
Typical
Application
See page 3
IGBT
IGBT
IGBT
SiC
SiC
SiC
MOSFET
MOSFET
MOSFET
FEATURES
Patents protected
No opto feedback
Optimised bipolar output voltages for IGBT/
SiC & MOSFET gate drives
Configurable dual outputs for all gate drive
applications:
+15V/-5V, +15V/-10V & +20V/-5V outputs
UL60950 Reinforced isolation to 690Vrms
Recognition pending
IEC 61800-5-1 recognition pending
Characterised dv/dt immunity 80kV/
μ
s at
1.6kV
Characterised partial discharge performance
14mm Creepage and clearance
Ultra low coupling capacitance 13pF
DC link voltage 3kVDC
5V, 12V & 24V input voltages
105°C operating temperature
Order Code
1
MGJ6D051510WMC
MGJ6D121510WMC
MGJ6D241510WMC
MGJ6D052005WMC
MGJ6D122005WMC
MGJ6D242005WMC
MGJ6D051505WMC
MGJ6D121505WMC
MGJ6D241505WMC
V
4.5 - 9
9 - 18
18 - 36
4.5 - 9
9 - 18
18 - 36
4.5 - 9
9 - 18
18 - 36
V
+15
+15
+15
+20
+20
+20
+15
+15
+15
mA
240
240
240
240
240
240
300
300
300
W
3.6
3.6
3.6
4.8
4.8
4.8
4.5
4.5
4.5
V
-10
-10
-10
-5
-5
-5
-5
-5
-5
mA
240
240
240
240
240
240
300
300
300
W
2.4
2.4
2.4
1.2
1.2
1.2
1.5
1.5
1.5
SELECTION GUIDE (Continued)
Output 1
Load Regulation (Max)
Load Regulation (Typ)
Load Regulation (Typ)
Ripple & Noise (Max)
2
Ripple & Noise (Typ)
2
Output 2
Load Regulation (Max)
Ripple & Noise (Max)
2
120
120
120
120
120
120
120
120
120
Ripple & Noise (Typ)
2
80
80
80
80
80
80
80
80
80
Input
Voltage
Range
V
MGJ6D051510WMC
MGJ6D121510WMC
MGJ6D241510WMC
MGJ6D052005WMC
MGJ6D122005WMC
MGJ6D242005WMC
MGJ6D051505WMC
MGJ6D121505WMC
MGJ6D241505WMC
4.5 - 9
9 - 18
18 - 36
4.5 - 9
9 - 18
18 - 36
4.5 - 9
9 - 18
18 - 36
Typical
Application
See page 3
IGBT
IGBT
IGBT
SiC
SiC
SiC
MOSFET
MOSFET
MOSFET
PRODUCT OVERVIEW
With 14mm creepage and clearance distances and
reinforced insulation rating of 690VAC, the MGJ6
14mm is ideally suited for use in higher efficiency
690VAC industrial electrical distribution systems.
Offering configurable dual output voltages of +15V/-
10V, +20V/-5V and +15V/-5V, the MGJ6 series of
DC-DC converters is ideal for powering ‘high side’
and ‘low side’ gate drive circuits for IGBTs, Silicon
and Silicon Carbide MOSFETs in bridge circuits.
A choice of asymmetric output voltages allows
optimum drive levels for best system efficiency
and EMI. The MGJ6 series is characterised for high
isolation and dv/dt requirements commonly seen in
bridge circuits used in motor drives and inverters.
%
5
5
5
5
5
5
5
5
5
10
10
10
10
10
10
10
10
10
mVp-p
105
105
105
105
105
105
105
105
105
160
160
160
160
160
160
160
160
160
5
5
5
5
5
5
5
5
5
%
10
10
10
10
10
10
10
10
10
mVp-p
For full details go to
www.murata-ps.com/rohs
1. Components are supplied in tape and reel packaging, please refer to package specification section. Orderable part numbers are
MGJ6DXXXXXXWMC-R7 (25 pieces per reel), or MGJ6DXXXXXXWMC-R13 (140 pieces per reel).
2. See ripple & noise test method.
All specifications typical at T
A
=25°C, nominal input voltage and rated output current unless otherwise specified.
www.murata-ps.com/support
KDC_MGJ6-14mm.A04
Page 1 of 12
Output Power
MGJ6 14mm Series
10.2kVDC Isolated 6W Gate Drive SM DC-DC Converters
SELECTION GUIDE (Continued)
Isolation Capacitance
MTTF
1
Nominal Input
Voltage
Input Current
at Rated Load
Efficiency
(Min)
Efficiency
(Typ)
Order Code
V
MGJ6D051510WMC
MGJ6D121510WMC
MGJ6D241510WMC
MGJ6D052005WMC
MGJ6D122005WMC
MGJ6D242005WMC
MGJ6D051505WMC
MGJ6D121505WMC
MGJ6D241505WMC
5
12
24
5
12
24
5
12
24
mA
1500
620
300
1500
620
300
1500
620
300
74
76.5
78
74
76.5
78
74
76.5
78
%
77.5
80
81.5
77.5
80
81.5
77.5
80
81.5
pF
13
13
13
13
13
13
13
13
13
669
789
784
669
789
784
669
789
784
kHrs
21.388
19,546
19,570
21.388
19,546
19,570
21.388
19,546
19,570
INPUT CHARACTERISTICS
Parameter
Voltage range
Conditions
5V input types
12V input types
24V input types
Turn on threshold MGJ6D05
Turn off threshold MGJ6D05
Turn on threshold MGJ6D12
Turn off threshold MGJ6D12
Turn on threshold MGJ6D24
Turn off threshold MGJ6D24
5V input types
Min.
4.5
9
18
Typ.
5
12
24
4.1
3.0
8.1
7.5
16.7
16.3
20
50
38
Max.
9
18
36
Telcordia
MIL 217
Units
V
Under voltage lock out
V
Input ripple current
12V input types
24V input types
mA
p-p
OUTPUT CHARACTERISTICS
Parameter
Minimum load
Voltage set point accuracy
Line regulation
Total Regulation
Transient response
Conditions
Below 10% load, 5V and 15V outputs are clamped to 6V and 17V respectively
Output 1
Output 2
Low line to high line
Peak deviation (50-100% & 100-50% load swing)
Settling time
Min.
10
Typ.
±3
±5
Max.
Units
%
%
2
15
0.5
0.3
%
%
%V
out
ms
GENERAL CHARACTERISTICS
Parameter
Switching frequency
Conditions
Min.
Typ.
100
Max.
Units
kHz
www.murata-ps.com/support
KDC_MGJ6-14mm.A04
Page 2 of 12
MGJ6 14mm Series
10.2kVDC Isolated 6W Gate Drive SM DC-DC Converters
TEMPERATURE CHARACTERISTICS
Parameter
Operation
Storage
Product temperature rise above ambient
Conditions
See derating graphs
100% Load, Nom V
IN
, Still Air
Min.
-40
-55
Typ.
Max.
105
125
Units
°C
20
ISOLATION CHARACTERISTICS
Parameter
Isolation test voltage
Resistance
Continuous barrier withstand voltage
Conditions
Flash tested for 1 second
Qualification tested for 1 minute
Viso = 1kVDC
Non-safety barrier application
Min.
10200
10200
100
Typ.
Max.
Units
VDC
GΩ
VDC
3000
ABSOLUTE MAXIMUM RATINGS
Short-circuit protection
Input voltage, MGJ6 5V input types
Input voltage, MGJ6 12V input types
Input voltage, MGJ6 24V input types
Continuous
12V
20V
40V
RoHS COMPLIANCE, MSL AND PSL INFORMATION
This series is compatible with RoHS soldering systems with a peak reflow solder temperature of 245ºC and Time Above
Liquidus for 90 seconds. as per J-STD-020D.1. The pin termination finish on this product series is Gold with Nickel
Pre-plate. The series is backward compatible with Sn/Pb soldering systems. The series has a Moisture Sensitivity Level
(MSL) 2. Samples of the product series were tested in accordance with the conditioning described for MSL level 2 in
IPS/J-STD-020D.1. The product series passed electrical tests, co-planarity and visual inspection criteria.
www.murata-ps.com/support
KDC_MGJ6-14mm.A04
Page 3 of 12
MGJ6 14mm Series
10.2kVDC Isolated 6W Gate Drive SM DC-DC Converters
APPLICATION NOTES
Start-up times
Typical start up times for this series, with no additional output capacitance are:
Start-up times
ms
15
15
15
Output capacitance must not exceed:
Output Voltage
V
-5
-10
15
20
Maximum output
capacitance
μF
470
220
220
150
Part No.
MGJ6D051510WMC
MGJ6D121510WMC
MGJ6D241510WMC
Disable/Frequency synchronisation
Please refer to application notes for further information.
Disable/Synch
1
Pull Down Current
Input High
Input Low
Frequency Range
Duty Cycle
Min
2
0
90
25
Typ
0.5
Max
5
0.8
110
75
Units
mA
V
V
kHz
%
Synchronisation
100
The Disable/Synchronization pin has three modes:
1. When a dc logic low voltage is applied to this pin the MGJ6 is disabled and enters a low quiescent current sleep mode.
2. When this pin is left floating or a dc logic high (CMOS/TTL compatible) voltage is applied the MGJ6 is enabled and operates at the programmed frequency of 100kHz.
3. When a square wave of between 90kHz and 110kHz is applied to this pin, the switcher operates at the same frequency as the square wave. The falling edge of the
square wave corresponds to the start of the switching cycle. If the signal is slower than 25Hz, it will be interpreted as enabling and disabling the part. If the MGJ6 is
disabled, it must be disabled for 7 clock cycles before being re-enabled.
Note: The DIS/Sync pin is a high impedance TTL input and can be triggered by noise from external circuits if not treated carefully. It is advised that any pcb traces
connected to the DIS/Sync pin are kept as short as possible and away from other noisy pcb traces. The track should follow a similar route to the return path to avoid
differential noise pick up. If the pin is not used for synchronisation then a 22nF capacitor can be added from DIS/Sync pin to –Vin to suppress noise.
Output configurations for power switches
Terminal
(P5)
15V Output
(P4)
15V Return
5VA Output
(P3)
5VA Return
5VB Output
(P2)
5VB Return
IGBT
+15V
0.24A
0V
SIC
+20V
0.24A
No connection
MOSFET
+15V
0.3A
0V
No connection
-10V
0.24A
0V
-5V
0.24A
-5V
0.3A
No connection
www.murata-ps.com/support
KDC_MGJ6-14mm.A04
Page 4 of 12
MGJ6 14mm Series
10.2kVDC Isolated 6W Gate Drive SM DC-DC Converters
微控制器 MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
