REVISIONS
LTR
B
DESCRIPTION
Change to military drawing format. Add case outline 2. Inactivate G and P
case outlines for device types 01 and 02 for new design. Delete vendor
CAGE 34371. Editorial changes throughout.
Add three vendors, CAGE 07933, CAGE 64155, and CAGE 54186. Make
changes to paragraphs 1.2.2, 4.2, and 4.3. Make changes to table I, table II,
and figure 1. Editorial changes throughout.
Changes in accordance with NOR 5962-R062-93.
Make correction to marking paragraph 3.5. Drawing updated to reflect current
requirements. Redrawn. -rrp
DATE (YR-MO-DA)
87-07-24
APPROVED
M. A. FRYE
C
89-01-24
M. A. FRYE
D
E
93-07-13
06-03-01
M. A. FRYE
R. MONNIN
CURRENT CAGE CODE 67268
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
REV
SHEET
PREPARED BY
RICK OFFICER
E
1
E
2
E
3
E
4
E
5
E
6
E
7
E
8
E
9
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
WILLIAM J. JOHNSON
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
APPROVED BY
MICHAEL A. FRYE
MICROCIRCUIT, LINEAR, LOW OFFSET
OPERATIONAL AMPLIFIERS, MONOLITHIC
SILICON
DRAWING APPROVAL DATE
83-04-15
AMSC N/A
REVISION LEVEL
E
SIZE
A
SHEET
CAGE CODE
14933
1 OF
9
82036
DSCC FORM 2233
APR 97
5962-E102-06
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
82036
01
G
X
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
02
Generic number
OP-07A
OP-07
Circuit function
Operational amplifier, ultra low offset
Operational amplifier, low offset
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
G
P
2
Descriptive designator
MACY1-X8
GDIP1-T8 or CDIP2-T8
CQCC1-N20
Terminals
8
8
20
Package style
Can
Dual-in-line
Square leadless chip carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
Supply voltage (V
CC
) .......................................................
Input voltage range (V
IN
) ...............................................
Differential input voltage range .......................................
Output short circuit duration ...........................................
Lead temperature (soldering, 60 seconds) .....................
Storage temperature range ............................................
Thermal resistance, junction-to-case (θ
JC
) ......................
Thermal resistance, junction-to-ambient (θ
JA
):
Cases P and 2 .............................................................
Case G ........................................................................
Maximum power dissipation (P
D
): 2/
Case G ........................................................................
Cases P and 2 .............................................................
1.4 Recommended operating conditions.
Supply voltage range (V
CC
) ..........................................................
±5.0
V dc to
±20.0
V dc
Ambient operating temperature range (T
A
) ................................... -55°C to +125°C
±22
V dc
±V
CC
±30
V dc
1/
+300°C
-65°C to +150°C
See MIL-STD-1835
120°C/W
150°C/W
330 mW at T
A
= +125°C
400 mW at T
A
= +125°C
1/ Output may be shorted to ground indefinitely at V
S
=
±15
V, T
A
= +25°C. Temperature and supply voltages must be limited
to ensure dissipation rating is not exceeded.
2/ Must withstand the added P
D
due to short circuit test, e.g., I
OS
.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
82036
SHEET
E
2
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 -
MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at
http://assist.daps.dla.mil/quicksearch/
or
http://assist.daps.dla.mil
or
from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections and logic diagrams. The terminal connections and logic diagrams shall be as specified on figure
1.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed
in 1.2 herein. In addition, the manufacturer's PIN may also be marked.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
82036
SHEET
E
3
TABLE I. Electrical performance characteristics.
Conditions
-55°C
≤
T
A
≤
+125°C
V
CC
=
±15
V, unnuled,
V
CM
= 0
unless otherwise specified
Test
Symbol
Group A
subgroups
Device
type
Limits
Unit
Min
Input offset voltage
V
IO
1/ 2/
2/
1/ 2/
2/
Input offset voltage
temperature sensitivity
Input bias current
dV
IO
/dT
3/
1
2, 3
1
2, 3
2, 3
01
02
+I
IB
1
2, 3
1
2, 3
-I
IB
1
2, 3
1
2, 3
Input offset current
+I
IO
1
2, 3
1
2, 3
Power supply rejection ratio
+PSRR
V
CC
+ = 20 V to 5 V,
V
CC
- = -15 V
V
CC
+ = 15 V,
V
CC
- = -20 V to -5 V
V
CM
=
±10
V
V
CM
=
±13
V
Output short circuit current
I
OS(+)
I
OS(-)
Supply current
I
CC
t
≤
25 ms 4/
1
2, 3
-PSRR
1
2, 3
Common mode rejection
ratio
CMRR
1
2, 3
1, 2
3
1, 2
3
1
2, 3
See footnotes at end of table.
01, 02
01, 02
01, 02
110
106
-65
-70
01, 02
02
01
02
01
02
01
02
01
-25
-60
-75
-200
-0.6
-1.3
-2
-4
-3
-6
-2
-4
-3
-6
-2
-4
-2.8
-5.6
Max
25
60
75
200
0.6
1.3
2
4
3
6
2
4
3
6
2
4
2.8
5.6
10
20
10
20
dB
µV/V
nA
nA
µV/°C
µV
mA
65
70
4
5
mA
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
82036
SHEET
E
4
TABLE I. Electrical performance characteristics - Continued.
Conditions
-55°C
≤
T
A
≤
+125°C
V
CC
=
±15
V, unnuled,
V
CM
= 0
unless otherwise specified
Test
Symbol
Group A
subgroups
Device
type
Limits
Unit
Min
Output voltage swing
(minimum)
Open loop voltage gain
(single ended)
V
OP
R
L
= 1 kΩ
R
L
= 2000
Ω
A
VS
T
A
= +25°C
5/
T
A
= +25°C
5/
1/
2/
3/
4/
5/
5/
5/
4
5, 6
4
5, 6
02
01
4, 5, 6
01, 02
-10
-12
300
200
200
150
Max
10
12
V/mV
V
Users are cautioned to use the group C end-point limits for design purposes due to drift experienced with this parameter
during steady-life test (see table III).
Testing will occur at least 250 ms after application of power.
Shall be guaranteed if not tested, to the specified parameters.
Continuous short circuit limits are considerably less than the indicated test limits since maximum power dissipation cannot
be exceeded.
V
OUT
= 0 V to +10 V for A
VS
(+) and V
OUT
= 0 to -10 for A
VS
(-). R
L
= 2000
Ω.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-38535,
appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
82036
SHEET
E
5
测试/测量
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
