MEDIUM-VOLTAGE HIGH CURRENT POWER SUPPLIES
HITEK POWER MV3000 SERIES
The HiTek Power MV3000 series high performance,
medium output voltage power supplies feature a wide
output range for OEM and industrial applications. The
MV3000 meets the exacting requirements found in electron
beam, ion beam, chemical purification systems, magnet
drivers, and other 24/7 production processes.
®
PRODUCT HIGHLIGHTS
3 kW output power
Output voltages: 100, 150, 200, 250,
TYPICAL APPLICATIONS
Electron beam
Ion beam
X-ray
Laser diodes
HV pulse generator bias
HV amplifier bias
Magnet bias
Chemical purification
Test and measurement
Automated test
Heating
Semiconductor processing
and 300V
Parallel/series operation
High stability
Exceptional reliability
Full local and remote control
monitoring
Voltage or current control
High packing density: 3 kW in 2U
Stackable, cooling is front to rear
Active power factor correction
CE marked for EU LV Directive
2006/95/EC
Custom options available
©2018 Advanced Energy Industries, Inc.
HITEK POWER MV3000 SERIES
ELECTRICAL SPECIFICATIONS
Output Power
Output Voltage
Output Current
Input Voltage
Input Current
Polarity
3000 W at max output voltage and current
100 to 300 V
10 to 30 A depending on output voltage
185 to 255 VAC 47 to 63 Hz single phase plus protective earth, operation below 185 VAC is possible
with power derating down to 1500 W at 85 VAC
Not exceeding 19 ARMS, harmonics are controlled with active power factor correction
All models provide positive polarity. The output can be isolated from the chassis to provide negative
outputs if required.
Control signals are referenced to the negative output.
Output Ripple
Current Mode
Line Regulation
Load Regulation
Voltage mode: < 0.1% peak to peak of rated output voltage +50 mV peak to peak
< 0.2% peak to peak of rated output current +50 mA peak to peak
< 0.05% deviation in output voltage set point for a 10% change in supply line voltage
Current mode: < 0.1% deviation in output current set point for a 0 to 100% change in output voltage
Voltage mode: < 0.1% deviation in output voltage set point for a 0 to 100% change in load current
Transient Response
Temperature Coefficient
Drift
Protection
Response for a 10% to 90% or 90% to 10% step change in load. Overshoot/undershoot < 2% of rated output.
Recovery to within 0.1% of rated output < 10 ms.
100 ppm/°C
< 0.5% per 8 h after 1 h warmup
Over temperature
Output overvoltage (tracking demand available)
Output overcurrent (tracking demand available)
Fan failure
Input undervoltage
Operating Temperature
Storage Temperature
Humidity
Altitude
Usage
Installation Category
Pollution Degree
Metering
0 to +40°C (32°F to 140°F) ambient and air intake
-20 to +85°C (-4°F to 185°F)
80% max relative humidity up to 31ºC, decreasing linearly to 50% at 40°C
Sea level to 2000 m (6500')
Indoor use only
II (BSEN 61010)
2 (BSEN 61010)
Provided as part of an alphanumeric display.
Voltage meter reads 0 V to full output; resolution is < 0.5% of rated output.
Current meter reads 0 A to full output; resolution is < 1.5% of rated output.
Set point voltage (current) is displayed when the voltage (current) control knob is depressed.
Status Indication
If a trip occurs, the V and A information will be overwritten by the cause of the trip which may be one of:- ‘OVER
VOLTAGE’, ‘OVER TEMPERATURE’, ‘OVER CURRENT, ’USER I/L OPEN’, or ‘LOOP CONTROL’. In addition the
trip LED will illuminate.
Fan assisted with fan fail detection. Air inlets at the front of the unit, exhaust on the rear. Min air flow inlet rate
is 3 ms-1.
For shelf mounting a 25 mm gap must be provided at the front and rear of the unit for air exhaust. No gap above
or below the unit is necessary.
Cooling
2
advanced-energy.com
微控制器 MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
