Thick film low ohmic chip resistors for current detection
UCR series
●
Datasheet
Features
1)Very-low ohmic resistance from 11mΩ is in lineup by thick-film resistive element.
2)Resistive element is located at bottom side, which reduces the resistance shift
during mounting process.
3)ROHM's unique structure achieved improvement of heat.
4)ROHM resistors have obtained ISO9001 / ISO / TS16949 certification.
5)Corresponds to AEC-Q200. But UCR006 is preraring.
UCR03 (under 100mΩ or less) are unsupprted.
●
Products list
Size
Part No.
(mm)
(inch)
0201
Rated Power
(70
℃
)
(W)
0.1
Resistance
tolerance
(%)
F ( ±1% )
J ( ±5% )
F ( ±1% )
J ( ±5% )
F ( ±1% )
J ( ±5% )
F ( ±1% )
J ( ±5% )
F ( ±1% )
T
emperature
coefficient
(ppm /
℃
)
0
½
+300
0
½
300
0
½
250
0
½
200
0
½
250
0
½
200
0
½
150
0
½
150
0
½
250
0
½
150
250±200
0
½
250
0
½
150
0
½
350
0
½
200
0
½
150
0.100
≦
R<1
0.068
≦
R<0.100
0.100
≦
R<0.220
0.220
≦
R
≦
0.910
0.020
≦
R<0.050
0.050
≦
R<0.100
0.100
≦
R<0.200
0.220
≦
R
≦
0.910
0.020
≦
R
≦
0.047
0.047
＜
R
＜
0.1
0.011
≦
R
＜
0.020
0.020
≦
R
≦
0.047
0.047
＜
R
＜
0.1
0.011
≦
R<0.020
0.020
≦
R
≦
0.039
0.039
＜
R
＜
0.1
Resistance range
(Ω)
(E24series)
(E24series)
(E24series)
(E24series)
(E24series)
(E24series)
(E24series)
(E24series)
(E24series)
(E24series)
(E24series)
(E24series)
(E24series)
(E24series)
(E24series)
(E24series)
Operating
temperature
range
(
℃
)
-55
½
+155
UCR006
UCR01
0603
1005
0402
0.125
-55
½
+155
0.25
UCR03
1608
0603
0.20
-55
½
+155
UCR10
2012
0805
0.33
J ( ±5% )
-55
½
+155
UCR18
3216
1206
0.5
F ( ±1% )
J ( ±5% )
-55
½
+155
* Design and specifications are subject to change without notice.
Carefully check the specification sheet supplied with the product before using or ordering it.
●
Part Number Description
UCR
Part No.
1 0
Size (mm [inch])
006 (0603 [0201])
01 (1005 [0402])
03 (1608 [0603])
10 (2012 [0805])
18 (3216 [1206])
Part No.
UCR006
UCR01
EVH
Packaging specifications code
Code
YVP
MVP
EWP
UCR03
(20mΩ
½
47mΩ)
J
Resistance
tolerance
F ( ±1% )
J ( ±5% )
L
Special
part code
S
：
0.011
½
0.091Ω
L
：
0.1Ω
R1 0
Nominal resistance
Resistance code,3 or 4 digits.
Resistance
tolerance
+
Specialcode
Resistance
code
：
：
UCR
(Thick film low
ohmic chip
resistors)
Packaging
Quantity
specifications / Reel
Paper tape
( 2mm Pitch)
Paper tape
( 2mm Pitch)
Paper tape
( 4mm Pitch)
Paper tape
( 4mm Pitch)
Paper tape
( 4mm Pitch)
15,000
10,000
FS,FL,JS
JL
4 digits
3 digits
5,000
5,000
5,000
EVP
(51mΩ
½
910mΩ)
UCR10
UCR18
EVH
EVH
www.rohm.com
c 2016 ROHM Co., Ltd. All rights reserved.
1/4
2015.01 - Rev.E
UCR series
●
Datasheet
Derating curve
When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below.
■
UCR006/01/03/10/18
●
Characteristics
(UCR01/03/10/18)
T items
est
Guaranteed value
Resistor type
T conditions
est
20
℃
Measuring method : Measure Bottom termination
by 4 proves.
Resistance
See P.1
Variation of resistance
with temperature
Overload
See P.1
±(2.0
％＋
0.005Ω)
Anew uniform coating of minimum
of 95% of the surface being
immersed and no soldering
damage.
±(1.0
％＋
0.005Ω)
No remarkable abnormality on the appearance.
±(1.0
％＋
0.005Ω)
±(3.0
％＋
0.005Ω)
±(3.0
％＋
0.005Ω)
Measurement
：
+25/-55, +25/+125
℃
Rated voltage(current)×2.5
，
2
Rosin-ethanol solution25% (Wweight)
Soldering condition
：
245±5
℃
Duration of immersion
：
2.0±0.5s
Soldering condition
：
260±5
℃
Duration of immersion
：
10±1s
T temp
：
-55
℃½
+125
℃
5cycle
est
40
℃，
93
％
(Relative humidity)
T time
：
1,000h
est
70
℃
,Rated voltage
1.5h:ON
－
0.5h:OFF
T time
：
1,000h
est
155
℃
T time
：
1,000h
est
23±5
℃
, Immersion cleaning, 5±0.5min
Solvent: 2-propanol
-
Compliance Standard(s) : IEC60115-8
JISC 5201-8
Solderability
Resistance to
soldering heat
Rapid change of
temperature
Damp heat, steady state
Endurance at 70
℃
Endurance
Resistance to solvent
Bend strength of
the end face plating
±(3.0
％＋
0.005)
±(0.5
％＋
0.005Ω)
Without open.
*Please contact us for guarantee of the test conditions other than those described above.
www.rohm.com
c 2016 ROHM Co., Ltd. All rights reserved.
3/4
2015.01 - Rev.E
Datasheet
Notice
Precaution on using ROHM Products
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment
(Note 1)
,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of
any ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASS
Ⅲ
CLASS
Ⅱ
b
CLASS
Ⅲ
CLASS
Ⅲ
CLASS
Ⅳ
CLASS
Ⅲ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities,
adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any
property, which a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3.
Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from
the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use
our Products under any special or extraordinary environments or conditions (as exemplified below), your
independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including
Cl2, H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue
of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for
cleaning residue after soldering
[h] Use of the Products in places subject to dew condensation
The Products are not subject to radiation-proof design.
Please verify and confirm characteristics of the final or mounted products in using the Products.
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively
affect product performance and reliability.
De-rate Power Dissipation (Pd) depending on Ambient temperature (T When used in sealed area, confirm the
a).
actual ambient temperature.
Confirm that operation temperature is within the specified range described in the product specification.
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined
in this document.
4.
5.
6.
7.
8.
9.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect
product performance and reliability.
2.
In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
c 2016 ROHM Co., Ltd. All rights reserved.
Rev.001
工业自动化与控制
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
