8
7
6
5
4
3
ZONE
REV.
2
REVISIONS
DESCRIPTION
1
DATE
APPROVED
DETAIL 1
D
ALL
A
B
C
D
TABLE REDRAWN ECO 3290
REMOVED UNUSED P/N#
ADDED TS209N
ADDED TS-425
12/10/86
02/10/09
03/04/11
09/13/12
D
1.000
.180
A
.291
DETAIL A
SCALE 2 : 1
.100±.010
DETAIL 2
C
+.015
.115
- .000
.210
C
1.000
A
.500
1.000 2 PL.
.281 .093
.291
2.000
A
B
DETAIL 3
B
1.000
1.000
A
.291
UNLESS OTHERWISE SPECIFIED:
NAME
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
THIRD ANGLE PROJECTION
TRUSHAR
DATE
02/06/09
A
5.
4.
3.
2.
1.
DEGREASE
STRAIGHT WITHIN .015/10" IN LENGTH
CUT ENDS TO BE SQUARE WITHIN .0025/INCH IN WIDTH
REMOVE ALL BURRS
MAT'L: AL. EXTRUSION, 6063-T6, PRE-ANOD., P/N TS100
8
7
6
5
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: 1
TWO PLACE DECIMAL
.03
THREE PLACE DECIMAL .010
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
VECTOR ELECTRONICS & TECH., INC. ANY MATERIAL
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
FINISH
VECTOR ELECTRONICS & TECH., INC. IS
PROHIBITED.
DO NOT SCALE DRAWING
T-STRUT
W/O INSERTS
SIZE DWG. NO.
11115 VANOWEN ST.,
NORTH HOLLYWOOD,
CA 91605
A
1
B
NOTES: UNLESS OTHERWISE SPECIFIED.
SCALE: 1:1 WEIGHT:
2
5280006
1
REV
SHEET 1 OF 1
D
4
3
8
7
6
5
4
3
ZONE
REV.
2
REVISIONS
DESCRIPTION
1
DATE
APPROVED
ALL
-
A1
RELEASED FOR PROTOTYPE
100 UNITS OF CCK13S
50 CCM14S & 50 CCK13S
P/N TS81-5 NO. OF HOLES WAS 30
ACTUAL STOCK PARTS HAVE 31
P/N TS81-5 "B" DIM. WAS 7.500
NO. OF HOLES WERE 31/ ECO2013
MOVED 1.000 DIM. LOCATION
CALLOUT FOR CLARITY NO ECO
ADDED TS81-6 &-7
INC ECO 2628
INC ECO 3924
REMOVED P/N# TS81-6, -7
TS169-5,TS209-5
ADDED P/N TS169-5/90
02/14/80
07/31/80
03/26/81
D
B
C
D
D
A
B .002
.250 TYP.
E
C
D
E
F
12/17/84
02/10/09
02/13/13
C
.250±.002 TYP.
4
.500±.015
G
.156 .060 +.030/-.000
6
7
1.000±.015
C
1.000±.060 TYP.
.291±.008 REF.
DETAIL E
SCALE 2 : 1
B
+.015
.115
- .000
B
.180
.100±.010
.210
UNLESS OTHERWISE SPECIFIED:
NAME
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
THIRD ANGLE PROJECTION
TRUSHAR
DATE
02/10/09
A
7.
6.
5.
4.
3.
2.
1.
TOOLING MARK MAY APPEAR
USE .1565 DIA. PUNCH TO FORM RADIUS EQUAL WITHIN .005 FROM C OF SLOT
L
PART TO BE FREE OF BURRS AND SURFACE SCRATCHES
NON CUMULATIVE TOLERANCE
PART TO BE STRAIGHT WITHIN .015/10 INCHES IN LENGTH
CUT ENDS TO BE SQUARE WITHIN .0025/INCH IN WIDTH
MAT'L: AL. EXTRUSION, 6063-T6, PRE-ANOD., P/N TS100
8
7
6
5
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: .X
TWO PLACE DECIMAL
.03
THREE PLACE DECIMAL .005
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
VECTOR ELECTRONICS & TECH., INC. ANY MATERIAL
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
FINISH
VECTOR ELECTRONICS & TECH., INC. IS
PROHIBITED.
DO NOT SCALE DRAWING
11115 VANOWEN ST.,
NORTH HOLLYWOOD,
CA 91605
T-STRUT
FOR SNAP-IN CARD GUIDE
SIZE DWG. NO.
A
1
B
NOTES: UNLESS OTHERWISE SPECIFIED.
M6336D4.2
1
REV
SCALE: 1:1 WEIGHT:
2
SHEET 1 OF 1
G
4
3
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
