MDT2005
MDT2005
1. General Description
This EPROM-Based 8-bit micro-controller uses a fully static CMOS design technology
combines higher speeds and smaller size with the low power and high noise immunity of
CMOS.
On chip memory system includes 0.5 K(for MDT2005) bytes of ROM, and 32 bytes of static
RAM.
2. Features
The followings are some of the features on the hardware and software :
u
Fully COMS static design
u
8-bit data bus
u
On chip ROM size : 512 words for MDT2005
u
Internal RAM size : 32 bytes
(25 general purpose registers, 7 special registers)
u
36 single word instructions
u
14-bit instructions
u
2-level stacks
u
Operating voltage : 2.3V ~ 6.3 V
u
Operating frequency : 0 ~ 20 MHz
u
The most fast execution time is 200 ns under 20 MHz in all single cycle instructions except
the branch instruction
u
Addressing modes include direct, indirect and relative addressing modes
u
Power-on Reset
u
Power edge-detector Reset
u
Sleep Mode for power saving
u
8-bit real time clock/counter(RTCC) with 8-bit programmable prescaler
u
4 types of oscillator can be selected by programming option:
RC－Low cost RC oscillator
LFXT－Low frequency crystal oscillator
XTAL－Standard crystal oscillator
HFXT－High frequency crystal oscillator
u
4 oscillator start-up time can be selected by programming option:
150
µs,
20 ms, 40 ms, 80 ms
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw
P. 1
VER1.1
MDT2005
u
On-chip RC oscillator based Watchdog Timer(WDT) can be operated freely
u
12 I/O pins with their own independent direction control
3. Applications
The application areas of this MDT2005 range from appliance motor control and high speed
automotive to low power remote transmitters/receivers, pointing devices, and
telecommunications processors, such as Remote controller, small instruments, chargers, toy,
automobile and PC peripheral … etc.
4. Pin Assignment
PA2
PA3
RTCC
/MCLR
V
ss
PB0
PB1
PB2
PB3
1
2
3
4
5
6
7
8
9
18
17
16
15
14
13
12
11
10
PA1
PA0
OSC1
OSC2
V
dd
PB7
PB6
PB5
PB4
5. Pin Function Description
Pin Name
PA0~PA3
PB0~PB7
RTCC
/MCLR
OSC1
OSC2
V
dd
V
ss
I/O
I/O
I/O
I
I
I
O
Function Description
Port A, TTL input level
Port B, TTL input level
Real Time Clock/Counter, Schmitt Trigger input levels
Master Clear, Schmitt Trigger input levels
Oscillator Input
Oscillator Output
Power supply
Ground
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw
P. 2
VER1.1
MDT2005
6. Memory Map
(A) Register Map
Address
00
01
02
03
04
05
06
07~1F
Description
Indirect Addressing Register
RTCC
PC
STATUS
MSR
Port A
Port B
Internal RAM, General Purpose Register
(1) IAR ( Indirect Address Register) : R0
(2) RTCC (Real Time Counter/Counter Register) : R1
(3) PC (Program Counter) : R2
Write PC, CALL --- always 0
LJUMP, JUMP, LCALL --- from instruction word
RTIW, RET --- from STACK
A9
A8
A7~A0
Write PC, JUMP, CALL --- always 0 (ROM 0.5K)
LJUMP, LCALL --- from instruction word
RTIW, RET --- from STACK
Write PC --- from ALU
LJUMP, JUMP, LCALL, CALL --- from instruction word
RTIW, RET --- from STACK
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw
P. 3
VER1.1
MDT2005
(4) STATUS (Status register) : R3
Bit
0
1
2
3
4
5-7
Symbol
C
HC
Z
PF
TF
——
Carry bit
Half Carry bit
Zero bit
Power loss Flag bit
Time overflow Flag bit
General purpose bit
Function
(5) MSR (Memory Select Register) : R4
(6) PORT A : R5
PA3~PA0, I/O Register
(7) PORT B : R6
PB7~PB0, I/O Register
(8) TMR (Time Mode Register)
Bit
Symbol
Prescaler Value
Function
RTCC rate
WDT rate
0 0 0
1:2
1:1
0 0 1
1:4
1:2
0 1 0
1:8
1:4
0 1 1
1 : 16
1:8
1 0 0
1 : 32
1 : 16
1 0 1
1 : 64
1 : 32
1 1 0
1 : 128
1 : 64
1 1 1
1 : 256
1 : 128
Prescaler assignment bit :
0
—
RTCC
1
—
Watchdog Timer
RTCC signal Edge :
0
—
Increment on low-to-high transition on RTCC pin
1
—
Increment on high-to-low transition on RTCC pin
RTCC signal set :
0
—
Internal instruction cycle clock
1
—
Transition on RTCC pin
2—0
PS2—0
3
PSC
4
TCE
5
TCS
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw
P. 4
VER1.1
MDT2005
(9) CPIO A, CPIO B (Control Port I/O Mode Register)
The CPIO register is “write-only”
＝“0”,
I/O pin in output mode;
＝“1”,
I/O pin in input mode.
(10) EPROM Option by writer programming :
Oscillator Type
RC
Oscillator
Oscillator Start-up Time
150
µs,20ms,40ms,80ms
20 ms,40ms,80ms
20ms,40 ms,80ms
40 ms,80 ms
HFXT Oscillator
XTAL Oscillator
LFXT Oscillator
Watchdog Timer control
Watchdog timer disable all the time
Watchdog timer enable all the time
Power Edge Detect
PED
Disable
Security bit
Security weak Disable
Security Disable
Security Enable
PED Enable
The default EPROM security is weak disable. Once the IC was set in enable or disable, it’s
forbidden to set in disable or enable again.
(B) Program Memory
Address
000-1FF
1FF
Description
Program memory for MDT2005
The starting address of the power on, external reset
or WDT for MDT2005
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw
P. 5
VER1.1
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
