Absolute Maximum Ratings (Unless otherwise specified, Tj=25°C)
Inverter Part
Item
Symbol
Ratings
Unit
Supply Voltage
Supply Voltage(Surge)
Collector-Emitter Voltage
Collector Current
DC
PEAK
V
P
V
P(surge)
V
CES
I
C
I
CP
P
C
T
jmax
450
500
600
±10
±30
(Note 1)
(Note 1)
Conditions
Applied between P-NU,NV,NW
Applied between P-NU,NV,NW
T
C
=25°C
T
C
=25°C, less than 1ms
T
C
=25°C, per 1 chip
V
V
V
A
A
W
°C
Collector Power Dissipation
Junction Temperature
(Note 1) Do not, however exceed P
C
, ASO.
33
150
Control part
Item
Control Power Supply
Floating Control Power Supply
Control Input Voltage
Fault Output Supply Voltage
Fault Output Current
Current Sensing Input Voltage
Bootstrap diode part
Item
Reverse Voltage
Junction Temperature
Total system
Item
Self Protection Supply Voltage
(SCP Capability)
Module Case Temperature
Storage Temperature
Isolation Voltage
Symbol
V
P(PROT)
T
C
T
stg
V
iso
Ratings
400
-25 to +100
-40 to +125
1500
Unit
V
°C
°C
V
rms
Sinusoidal, 60Hz, AC 1minute,
between connected all pins and heat sink
plate
Conditions
V
CC
=13.5 to 16.5V, Inverter part
T
j
=125°C, non-repetitive, less than 2µs
Measurement point of T
C
is provided
in Figure 2
Symbol
V
CC
V
BS
V
IN
V
FO
I
FO
V
CIN
Ratings
20
20
-0.5 to V
CC
+0.5
-0.5 to V
CC
+0.5
1
-0.5 to +7.0
Unit
V
V
V
V
mA
V
Conditions
Applied between HVCC-GND, LVCC-GND
Applied between VBU-U, VBV-V, VBW-W
Applied between HINX, LINX-GND
(X=U,V,W)
Applied between FO-GND
Sink current at FO pin
Applied between CIN-GND
Symbol
V
RB
T
jmaxD
Ratings
600
150
Unit
V
°C
Conditions
Thermal resistance
Item
Junction to Case Thermal
Resistance
(Note 2)
Symbol
R
th(j-c)_IGBT
R
th(j-c)_FWD
Limit
Min
-
-
Typ
-
-
Max
3.7
4.5
Unit
°C /W
°C /W
Conditions
Inverter IGBT(1/6 module)
Inverter FWD(1/6 module)
(Note 2) Grease with good conductivity and high reliability should be applied evenly with +100 to +200µm on the contacting surface of IPM and heat sink. Use
a torque wrench to fasten up to the specified torque rating. The contacting thermal resistance between IPM case and heat sink is determined by the
thickness and the thermal conductivity of the applied grease.
Caution:
Operating the IPM over the absolute maximum ratings may damage the IPM. The damage can either be a short circuit between pins or an open
circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IPM is
无线连接
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
