3M
™
Mini D Ribbon (MDR) Cable Assembly
.050” High Speed Digital CameraLink
™
Cable – Right Angle
14H26-SZ3X-XXX-0LC
• Supports Industrial CameraLink
™
standard for camera to
frame grabber communications
• Space-saving right angle cable exit
• 11 shielded twin-ax pairs and four drain wires
• Entire cable bundle is shielded with foil and braid for
additional signal protection
• Rugged MDR ribbon type contact
• Rugged thumbscrew retention
• EMI shielded junction shell on straight end
• EMI shielded overmolded shell on right-angle end
• See Regulatory Information Appendix (RIA) for chemical
compliance information
Date Modified: January 24, 2008
TS-2262-A
Sheet 1 of 3
Physical
Connector Contact Plating
Wiping Area: 30 µ ” [0.76 µm] Min. Gold (RIA E1 & C1 apply)
Overmolded Shell:
Color: Black
Material: Polyvinyl Chloride (PVC)
Shell:
Color: Beige
Material: Polyester Elastomer
Cable:
Color: Beige
Jacket Material: Polyvinyl Chloride (PVC)
Flammability: AWM VW-1
Electrical
Voltage Rating:
30V
Current Rating:
1 A
Insulation Resistance:
> 1 x 10
8
Ω
at 100 V
DC
Withstanding Voltage:
350 V
RMS
for 1 minute
Individually Shielded Twisted Pairs
Characteristic Impedance:
100 ± 10
Ω
Conductor Size:
28 AWG Stranded
Propagation Velocity:
1.25 ns/ft [4.1 ns/m ]
Skew (within pair):
50 ps/meter maximum
Skew (channel skew per chipset):
50 ps/meter maximum
Environmental
Temperature Rating:
-20 °C to +75 °C
UL File No.: E86982
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M
™
Mini D Ribbon (MDR) Cable Assembly
.050” High Speed Digital CameraLink
™
Cable – Right Angle
Right-Angle End
14H26-SZ3X-XXX-0LC
Straight End
39.7
[1.56]
19.4
[0.76]
#4-40
Thumbscrews
39.7
[1.56]
2X 26 Position High Density
Mini D Ribbon (MDR) Male Plug
12.8
[0.51]
Cable Length
42.4
[1.67]
32.5
[1.28]
Cable Length Tolerance is
the Larger of +50mm / -0mm
or +3% / -0%
MDR 26 Position Plug
Right-Angle End
MDR 26 Position Plug
Straight End
1
13
14
26
mm
[inch]
Tolerance Unless
Noted
14H26-SZ3M-XXX-0LC
14H26-SZ3S-XXX-0LC
mm
Use 3M
™
Jacksocket 3341-31 for mounting receptacle to panel.
[ ] Dimensions for
Reference Only
.0
±.1
.00
±.10
Ordering Information
14H26-SZ3X-XXX-0LC
Right Angle Orientation
M = Position 1 opposite cable
S = Position 1 on cable side
050
100
150
200
250
=
=
=
=
=
50 cm
100 cm
150 cm
200 cm
250 cm
Cable Length
300
350
400
450
500
=
=
=
=
=
300 cm
350 cm
400 cm
450 cm
500 cm
600
700
800
900
A00
=
=
=
=
=
600 cm
700 cm
800 cm
900 cm
1000 cm
For lengths greater than 1000 cm refer to Table 2
TS-2262-A
Sheet 2 of 3
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M
™
Mini D Ribbon (MDR) Cable Assembly
.050” High Speed Digital CameraLink
™
Cable – Right Angle
Table 1. Cable Assembly and Camera Link Pinouts
Medium and Full Configurations
Two Channel Link Chips
Camera
Connector
1
14
2
15
3
16
4
17
5
18
6
19
7
20
8
21
9
22
13
23
11
24
12
15
13
26
Right Angle
Frame Grabber
1
14
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
13
26
Channel Link
Signal
inner shield
inner shield
Y0-
Y0+
Y1-
Y1+
Y2-
Y2+
Yclk-
Yclk+
Y3-
Y3+
100 ohm
terminated
Z0-
Z0+
Z1-
Z1+
Z2-
Z2+
Zclk-
Zclk+
Z3-
Z3+
inner shield
inner shield
Cable Name
(Reference only)
inner shield
inner shield
Pair 1
Pair 1
Pair 2-
Pair 2+
Pair 3-
Pair 3+
Pair 4-
Pair 4+
Pair 5-
Pair 5+
Pair 6+
Pair 6-
Pair 7-
Pair 7+
Pair 8-
Pair 8+
Pair 9-
Pair 9+
Pair 10-
Pair 10+
Pair 11-
Pair 11+
inner shield
inner shield
Base Configuration
One Channel Link Chip + Camera Control +
Serial Communication
Camera
Connector
1
14
2
15
3
16
4
17
5
18
6
19
7
20
8
21
9
22
13
23
11
24
12
15
13
26
Table 2
Length Codes
First 2
Digits
10
11
12
13
14
15
16
Alpha
Code
A
B
C
D
E
F
G
First 2
Digits
17
18
19
20
21
22
23
Alpha
Code
H
J
K
L
M
N
P
First 2
Digits
24
25
26
27
28
29
30
Alpha
Code
R
S
T
V
W
Y
Z
Right Angle
Frame Grabber
1
14
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
13
26
Channel Link
Signal
inner shield
inner shield
X0-
X0+
X1-
X1+
X2-
X2+
Xclk-
Xclk+
X3-
X3+
SerTC+
SerTC-
SerTFG-
SerTFG+
CC1-
CC1+
CC2+
CC2-
CC3-
CC3+
CC4+
CC4-
inner shield
inner shield
14H26-SZ3X-XXX-0LC
Notes:
1. All pairs are individually shielded with aluminum foil.
2. Pair shields are wrapped aluminum out and are in
contact with four internal drains (logic ground).
3. Outer braid and foil (chassis ground) are isolated
from inner drains (logic ground).
4. Cable assembly compatible with both CameraLink
configurations.
For lengths in excess of 1000 cm substitute the corresponding alpha code for the first 2 digits. Example: the code for 1160 cm is B60.
TS-2262-A
Sheet 3 of 3
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/717/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217B-D
Appendix E5: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under
Item 6 of the Annex to the Directive.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means
that the product or part
does not
contain any of the following substances in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part
does
contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
RIA-2217B-D
模拟与混合信号
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
