Datasheet> 器件分类 > 无源元件> MEM2012SC101T001

MEM2012SC101T001: 产品描述EMI Filter Circuits; 产品类别无源元件; 文件大小101KB，共7页; 制造商TDK(株式会社); 官网地址http://www.tdk.com

下载文档详细参数选型对比全文预览

MEM2012SC101T001在线购买

供应商	器件名称	价格	最低购买	库存
	MEM2012SC101T001	-	-	点击查看	点击购买

MEM2012SC101T001概述

EMI Filter Circuits

MEM2012SC101T001规格参数

参数名称	属性值
Product Attribute	Attribute Value
制造商 Manufacturer	TDK(株式会社)
产品种类 Product Category	EMI Filter Circuits
电路类型 Circuit Type	T Filter
电容 Capacitance	100 pF
电压额定值 Voltage Rating	12 V
电流额定值 Current Rating	1 A
最大工作温度 Maximum Operating Temperature	+ 85 C
最小工作温度 Minimum Operating Temperature	- 40 C
系列 Packaging	Cut Tape
系列 Packaging	Reel
Frequency Range	300 MHz to 2000 MHz
高度 Height	0.95 mm
长度 Length	2 mm
宽度 Width	1.25 mm
工厂包装数量 Factory Pack Quantity	4000

文档预览

下载PDF文档

全文
预览

E M C

C o m p o n e n t s

September 2015

3-terminal Filters

For signal line

MEM Series

MEM2012SC

Type

MEM2012SC

2012[0805 inch]*

Dimensions Code JIS[EIA]

(2/7)

E M C

C o m p o n e n t s

REMINDERS FOR USING THESE PRODUCTS

Before using these products, be sure to request the delivery specifications.

SAFETY REMINDERS

Please pay sufficient attention to the warnings for safe designing when using these products.

REMINDERS

The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH

or less).

If the storage period elapses, the soldering of the terminal electrodes may deteriorate.

Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).

Before soldering, be sure to preheat components.

The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature

does not exceed 150°C.

Soldering corrections after mounting should be within the range of the conditions determined in the specifications.

If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.

When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to

the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.

Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal

design.

Carefully lay out the coil for the circuit board design of the non-magnetic shield type.

A malfunction may occur due to magnetic interference.

Use a wrist band to discharge static electricity in your body through the grounding wire.

Do not expose the products to magnets or magnetic fields.

Do not use for a purpose outside of the contents regulated in the delivery specifications.

The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications

equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement

equipment, industrial robots) under a normal operation and use condition.

The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or

quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to

society, person or property.

If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions

set forth in the each catalog, please contact us.

(1) Aerospace/Aviation equipment

(2) Transportation equipment (cars, electric trains, ships, etc.)

(3) Medical equipment

(4) Power-generation control equipment

(5) Atomic energy-related equipment

(6) Seabed equipment

(7) Transportation control equipment

(8) Public information-processing equipment

(9) Military equipment

(10) Electric heating apparatus, burning equipment

(11) Disaster prevention/crime prevention equipment

(12) Safety equipment

(13) Other applications that are not considered general-purpose

applications

When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing

protection circuit/device or providing backup circuits in your equipment.

20150908 / 3tf_commercial_signal_mem2012sc_en.fm

MEM2012SC101T001相似产品对比

	MEM2012SC101T001	MEM2012SC220T001	MEM2012SC100	MEM2012SC100T001	MEM2012SC101	MEM2012SC220	MEM2012SC151
描述	EMI Filter Circuits	EMI Filter Circuits 12V 1A	EMI Filter Circuits 10pF 12V 1A 0.12ohms	EMI Filter Circuits	EMI Filter Circuits 100pF 12V 1A .12ohms	EMI Filter Circuits 22pF 12V 1A 0.12ohms	EMI Filter Circuits 150pF 12V 1A .12ohms
Product Attribute	Attribute Value	Attribute Value	-	Attribute Value	Attribute Value	Attribute Value	Attribute Value
制造商 Manufacturer	TDK(株式会社)	TDK(株式会社)	-	TDK(株式会社)	TDK(株式会社)	TDK(株式会社)	TDK(株式会社)
产品种类 Product Category	EMI Filter Circuits	EMI Filter Circuits	-	EMI Filter Circuits	EMI Filter Circuits	EMI Filter Circuits	EMI Filter Circuits
电容 Capacitance	100 pF	22 pF	-	10 pF	100 pF	22 pF	150 pF
电压额定值 Voltage Rating	12 V	12 VDC	-	12 V	12 VDC	12 VDC	12 VDC
电流额定值 Current Rating	1 A	1 A	-	1 A	1 A	1 A	1 A
最大工作温度 Maximum Operating Temperature	+ 85 C	-	-	+ 85 C	+ 85 C	+ 85 C	+ 85 C
最小工作温度 Minimum Operating Temperature	- 40 C	-	-	- 40 C	- 40 C	- 40 C	- 40 C
系列 Packaging	Reel	Reel	-	Reel	Reel	Reel	Reel
高度 Height	0.95 mm	0.8 mm	-	0.95 mm	0.8 mm	0.8 mm	0.8 mm
长度 Length	2 mm	2 mm	-	2 mm	2 mm	2 mm	2 mm
宽度 Width	1.25 mm	1.25 mm	-	1.25 mm	1.25 mm	1.25 mm	1.25 mm
工厂包装数量 Factory Pack Quantity	4000	4000	-	4000	4000	4000	4000
RoHS	-	Details	-	Details	Details	Details	Details
端接类型 Termination Style	-	SMD/SMT	-	-	SMD/SMT	SMD/SMT	SMD/SMT
封装 / 箱体 Package / Case	-	0805 (2012 metric)	-	-	0805 (2012 metric)	0805 (2012 metric)	0805 (2012 metric)
类型 Type	-	Three Terminal Filters	-	-	Three Terminal Filter for Signal Line	Three Terminal Filter for Signal Line	Three Terminal Filter for Signal Line
单位重量 Unit Weight	-	0.000194 oz	-	0.000282 oz	0.000194 oz	0.000194 oz	0.000194 oz

推荐资源

STM32CubeMX里如何打开官方代码BLUEMICROSYSTEM1: 看到论坛里有人使用STM32CubeMX开发，几经折腾，STM32CubeMX也装好了，STM32L4的库也装好了，忽然发现无法打开官方代码BLUEMICROSYSTEM1 ！一个一个的再去编写传感器读写代码不现实啊，请问哪 ......; dwwzl MEMS传感器

超声波传感资料: 超声波传感资料...; feifei 嵌入式系统

TMS3705应用: 手上有个TMS3705的RF头,不知道该怎么操作它,查阅资料说:将TXCT引脚拉低50ms然后拉高,3ms后SCIO就会输出数据,可是我这边按照这个方法测得,SCIO只输出一个短暂的脉冲,后面啥都没有了有用过的 ......; pic16F77 无线连接

imx6ull移植alsa: EK140P-6y-256m 内核版本：linux-4.1.15 交叉编译链：arm-poky-linux-gnueabi 文件系统：my_rootfs=L4115-core-image-base-myimx6a7.tar.bz2 下载： https://www.alsa-project.org/ ......; 明远智睿Lan 模拟电子

IAR EWARM 6.30 keymaker: 使用IAR EWARM 开发的各位童鞋们，这个是我历尽艰苦找到的Crack，绝对能用。...; liyuyao001 ARM技术

IC贴片转接板、USB转TTL空板完全免费赠送，是工程、采购人员不二之选: http://bbs.jjj8.cn/attachment/photo/Mon_1307/11883_4e311373864470633b9b479c9789e.jpg 新注册用户赠送20元现金券（12元体验券+领取体验券转发到微博额外8元），用20元现金券可以得到以下全 ......; yangmi88 单片机

器件捷径: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

热门器件

开源项目推荐更多

热门活动更多

热门文章更多

技术资料推荐更多